Vax V-008T User Manual

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 1

Bagless upright

Vax model number:

V-008T

Vax careline

0870 6061248

www.vax.co.uk

Please read carefully before using this cleaner.

Always fully extend the mains cable before use.

or future reference.

tain f

e

R

instruction manual

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 2

www.vax.co.uk

1. Diagram

V-008T

1

2

3

4

5

6

1

14

15

16

3

7

8

9

10

11

12

Fig.1/1

1 Handle grip
2 TurboTool
3

Hose
4 Dirt container release button
5 Crevice tool

Ext

6

- inside extension tube

ension tube

7 Dirt container

Air Directors

8

17

18

19

20

21

9 Centre dirt path
10 Clean release empty button
11

Carpet height adjuster
12 Scuff guard bumper
13 Cord grip

Hose guide

14
15 Cord wrap with quick release

Long power cord

16

17 Carry handle
18 Dust brush
19

Handle release pedal
20 On/Off pedal
21 Wheels

21

2

parts overview

!!!

!

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 3

Vax Careline 0870 606 1248

2. Safety Information

FOR HOUSEHOLD USE ONLY.

When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:

1. Only use the vacuum cleaner indoors on dry surfaces.

2. Turn off the vacuum cleaner controls before
connecting to or disconnecting from the mains
supply.

3. Always unplug the vacuum cleaner before connecting or
disconnecting the vacuum hose.

4. Close attention is necessary when used by or near
children. Do not allow children to use as a toy.

5. Use only as described in this manual. Use only the
manufacturer’s recommended attachments.

6. Do not use the vacuum cleaner with a damaged cord
or plug. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified person
for examination, repair or adjustment.

Call 0870 6061248 for your nearest service centre.

7. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.

8. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.

9. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.

10. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.

11. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.

12. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.

Do not vacuum up harmful or toxic material

13.
(chlorine bleach, ammonia, drain cleaner, etc).

14. Do not vacuum up hard or sharp objects such as glass,
nails, screws, coins, etc.

t use without the filt

Do no

15.

16. Use extra care when vacuuming on stairs.

17. Keep vacuuming area well lit.

acuum cleaner indoors in a c

e the v

or

t

S

18.

ers in place.

ool, dry area.

19. Turn off the switch before unplugging.

20. Use only CE-approved 13 amp extension cords. Non­approved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.

WARNING: Always switch off and unplug the

vacuum cleaner from the electrical outlet before
assembling, opening or emptying the dirt container, or
before connecting/disconnecting the attachments.

CAUTION: The vacuum cleaner is a very powerful

unit. Before plugging the cord into the outlet make
sure the switch is in the ‘off’ position. Hold the vacuum
cleaner firmly when starting and in use.

IMPORTANT: If the inlet or hose is blocked, switch

off the vacuum cleaner and remove the blockage(s)
before re-starting the vacuum cleaner.

IMPORTANT: Cleaning filters improves vacuum

performance. Make sure all filters are replaced back
into the vacuum cleaner before using.

This vacuum cleaner is intended for household use only
and not for commercial or industrial use.

PLEASE KEEP THESE INSTRUCTIONS
FOR FURTHER USE.

Motor Thermostat

IMPORTANT: The motor is equipped with a thermal

cut-out. If for any reason, the vacuum cleaner should

ver-heat, the thermostat will automatically turn the

o
unit off. Should this occur, unplug the vacuum cleaner
from the electrical outlet and turn off the switch.

e the dirt c

v

emo

R
filters. Allow the cleaner to cool for approximately one
(1) hour. To re-start, plug into an electrical outlet and
switch back on.

tainer and empty. Clean the

on

safety information

3

FRONTBACK

a

b

SIDE

c

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 4

www.vax.co.uk

3. How to Assemble

Handle Assembly: Tool required: Phillips screwdriver

Detach dirt container from back panel of cleaner by
pressing dirt container release button and tilting forward.

Fig.3/1

Slide handle through top of back panel. Insert carry handle
through holes in back panel (see Fig.3/2).

Re-attach dirt container by aligning bottom of dirt container
to bottom of cleaner and push forward to snap into place.

Fig.3/4

Secure Back Hose:

Wrap hose around back of hose caddy. Push hose wand
down into the right side of cleaner and push the handle
flat against the cleaner (Fig.3/5).

Fig.3/5

Fig.3/2

Insert one (1) screw through front of cleaner to secure handle.
Secure carry handle with two (2) 1” screws through front of
cleaner (see Fig.3/3).

Fig.3/3

4

assembly

Tool Storage:

Attach tools: (a) Slide the dust brush onto post on the
lower tool caddy with the bristles facing out. (b) Clip Turbo
Tool into the caddy on the front of the handle. (c) Slide the
extension tube / crevice tool into the round slot on the left
side of the cleaner (Fig.3/6).

Fig.3/6

a

b

c

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 5

4. How to Operate

Cord Release:

Turn Quick Cord Release for easy cord removal. Store cord
in cord grip (see page 2 - parts overview) to keep out of
the way while vacuuming (Fig.4/1).

Fig.4/3

Handle Release Pedal:

To release handle, push the handle release pedal located

Fig.4/1

Turn the carpet height adjuster to match the surface being
cleaned (Fig.4/2).

on the lower left side of the cleaner (Fig.4/4).

Vax Careline 0870 606 1248

IMPORTANT: For easiest adjustment, place cleaner in full
upright position.

Fig.4/2

CAUTION: Brush agitator continues to rotate while the
hose is removed or in use and at all times while cleaner is
on. Keep hair, loose clothing, fingers and all parts of the
body away from brush area while cleaner is on. Cleaner
must be in the upright position to lift rotation brush off
the carpet when cleaning above the floor.

On/Off P

Plug cord into electrical outlet. Turn cleaner on by
depressing foot pedal located on the back left side of the
cleaner (Fig.4/3).

edal:

Fig.4/4

Floor/Carpet Cleaning:

Move the handle and adjust it to the desired position for
(a) storing the upright, (b) operating the cleaner, and (c) de­press the handle release pedal again to clean under
furniture (see Fig.4/5).

Fig.4/5

operation

5

!

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 6

www.vax.co.uk

OTE:Rotating brush could cause area rug fringe to

N

become tangled within cleaner. Use caution when

vacuuming throw rugs with fringe..

Above Floor Cleaning:

Cleaner must be in its upright position to raise brushbar.

Fig.4/6

Remove the hose from the tool caddy (Fig.4/7).

xtension Tube:

E

If additional length is needed, use the extension tube and
crevice tool. Pull crevice tool out of extension tube. Use
extension tube and crevice tool together or separately.

Fig.4/9

Carry Handle:

Use the carry handle on the back of the cleaner to move it
from room to room (Fig.4/10).

Fig.4/7

Choose any of the handy accessories or use the hose
alone. Simply push the attachment firmly into the end of
the extension tube or hose handle. To remove tool, twist
and pull apart gently.

Fig.4/8

6

operation

Fig.4/10

!

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 7

5. Dirt Container & Filters:
Removal and Replacement

WARNING: To reduce the risk of injury from moving
parts, unplug before servicing.

Emptying the dirt container:

Press dirt container release button and remove dirt
container from cleaner (Fig.5/1).

Fig.5/3

Lift filter cartridge out of base of cleaner (Fig.5/4).

Vax Careline 0870 606 1248

Fig.5/1

Hold dirt container over dustbin and press clean release
dirt container button to empty. Snap dirt container back
into place after emptying (Fig.5/2).

Fig.5/2

Click buttons on the base of the cleaner towards the
outside edges to unlock filter cartridge (Fig.5/3).

Fig.5/4

Remove foam filter:

Remove the foam filter from the filter cartridge (Fig.5/5).

Fig.5/5

Clean pleated filter:

o remove

tbin t

er on the inside o

ed filt

ap the plea

T
excess dust and dirt from filter. If filter is still clogged, rinse
under (Fig.5/6).

t

f a dus

dirt container & filters

7

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 8

www.vax.co.uk

eplace filter cartridge:

R

Return filter cartridge to base of cleaner (Fig.5/9).

Fig.5/6

Wash foam filter:

Hold foam filter under running water to wash (Fig.5/7).
Ring excess water out of filter. Allow filter to dry for at
least 24 hours before replacing in filter cartridge.

Fig.5/9

Click buttons back into place to lock filter cartridge in base
of cleaner (Fig.5/10).

Fig.5/7

Replace foam filter:

Return the foam filter to the filter cartridge (Fig.5/8).

Fig.5/8

8

cleaning filters

Fig.5/10

To clean the air directors:

To remove Air Directors, rotate 1/4 turn counterclockwise
(Fig.5/11).

Fig.5/11

!

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 9

Pull out and wipe with a damp cloth to clean (Fig.5/12).

Regular Maintenance

Each time the dirt container is emptied, the filter
should be cleaned. Tap the filter firmly against the
inside of a dustbin until the dirt stops falling from the
filter.

The filter will be discoloured after use, but this will
not affect the filter’s performance.

Do not brush the filter.

The cleaning instructions may vary depending on the
dirt conditions. In some cases, more or less cleaning
of the filter may be required.

Fig.5/12

Vax Careline 0870 606 1248

Dry and return the air directors to the dirt container. Rotate
1/4 turn clockwise to lock in place (Fig.5/13).

Fig.5/13

Replace dirt container:

Return dirt container to cleaner. Align slot on bottom of
dirt container with tab on cleaner. Push to snap into place
(Fig.5/14).

6. Belt or Brushbar: Removal
and Replacement

Tool required: Phillips screwdriver

WARNING: To reduce the risk of injury from moving

parts, unplug cleaner before changing belt or
brushbar

.

To remove belt:

Lay cleaner flat and flip cleaner to expose nozzle base.
Base should lay flat and face up. The remove nozzle guard,
use Phillips screwdriver to remove the three (3)screws.
Arrows show location of screws (Fig.6/1).

Fig.6/1

Pull and lift nozzle guard off (Fig.6/2).

Fig.5/14

belt or brushbar replacement

9

MOTOR SHAFT

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 10

www.vax.co.uk

Place new belt in area of brushbar without bristles (Fig.6/5).

Fig.6/2

Lift and remove brushbar (Fig.6/3). Dispose of old belt.

Fig.6/5

With new belt in place, pull and slide brushbar into nozzle
making sure that the brushbar end caps are in the correct
orientation (inset). Rotate brushbar manually to make sure
belt is properly aligned (Fig.6/6).

Fig.6/3

To replace belt or brushbar:

Slide belt onto motor shaft (see Fig.6/4).

Fig.6/4

10

belt or brushbar replacement

Fig.6/6

Re-attach nozzle guard (Fig.6/7).

Fig.6/7

SLOTS

TABS

!

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 11

Vax Careline 0870 606 1248

Secure by aligning the three (3) tabs in the base slots.

Fig.6/8

Replace all three (3)screws to secure nozzle guard (see
Fig.6/9).

7. General Maintenance

WARNING: To reduce the risk of injury from moving

parts, unplug before servicing.

Debris removal - hose:

Check to see if dirt container is full; empty if needed

Plug cleaner in and check to see if there is any suction at
end of hose. If there is
debris removal section below. If there is no suction at the
end of the hose, follow these steps:

1 Remove the dirt container (see section 5) and check

dirt container inlet located on cleaner (Fig.7/1).

suction at end of hose, move on to

Fig.6/9

Fig.7/1

Debris removal - nozzle guard:

Remove nozzle guard (Fig.7/2) by removing three (3)
screws. Remove obstruction.

/2

Fig.7

general maintenance

11

L

OCKING RING

!

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 12

www.vax.co.uk

ebris removal - TurboTool:

D

Rotate locking ring 180° and turn TurboTool over (Fig.7/3).

Fig.7/3

Pivot lower housing and remove clog (Fig.7/4).

Fig.7/4

To reassemble, be sure tabs are engaged. Pivot the lower
housing closed (Fig.7/5).

8. Troubleshooting

maintenance or troubleshooting checks.

PROBLEM: Vacuum cleaner won't run
Cause:

Solution: Plug unit in firmly.
Cause: No electricity in the electrical outlet.

Solution: Check fuse or breaker.
Cause: Cleaner requires service.

Solution: Take your cleaner to a service centre. Call

Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the vacuum cleaner.

PROBLEM: Cleaner won’t pick up/loss of suction.
Cause:

Solution: Review dirt container replacement (section 5).
Cause: Dirt container full or blocked.

Solution: Empty dirt container (see section 5).
Cause: Brushbar or belt worn or broken.

Solution: Replace belt or brushbar (see section 6).
Cause: One or both filters are clogged.

Solution: Remove, clean and replace filters.
Cause: Nozzle / dirt passage clogged.

Solution: Open access door, remove obstruction

Cause: Carpet height setting is incorrect.
Solution: Set carpet height adjustment to appropriate

Cause: Hose clogged.
Solution: Remove hose and tools, remove obstruction

WARNING: To reduce the risk of personal injury,

unplug the vacuum cleaner before performing

Not properly plugged into electrical outlet.

0870 606 1248 to find your nearest Vax
approved service agent.

Leave for one (1) hour. See page 3.

Dirt container not installed properly.

(see section 7).

setting for carpet being cleaned.

(see section 7).

PROBLEM: Dust escaping from the vacuum cleaner.

Dirt container full.

orrectly.

talled c

t ins

w installation.

vie

e

Carpet height setting is incorrect.

setting for carpet being cleaned.

Fig.7/5

12

general maintenance / troubleshooting

Cause:
Solution: Empty dirt container.

Cause: Dirt container not installed.
Solution: Review dirt container replacement.

Cause: Hose no
Solution: R

Cause: Filter not installed completely.
Solution: Remove, clean and replace filter.

PROBLEM: Cleaner is difficult to push forwards.
Cause:

Solution: Set carpet height adjustment to appropriate

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 13

9. Technical Specification

Voltage: 220-240V ~50Hz
Wattage: 1550W
Capacity:
Filters: Foam and pleated HEPA pre motor filters
Cord length: 9.8m
Weight: 8.98kg

Subject to technical change without notice.

Vax Careline 0870 606 1248

technical specification

13

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 14

www.vax.co.uk

This page has been left intentionally blank

14

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 15

Vax Careline 0870 606 1248

This page has been left intentionally blank

15

Vax V-008T User Guide.qxd 28/6/07 13:57 Page 16

EEC STATEMENT OF COMPLIANCE

Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the

V-008T Performance Twin Cyclonic Upright is manufactured in compliance with the following Directives:

Safety: 2006/95/EC Low Voltage Directive

EMC: 89/336/EEC Electromagnetic Compatibility Directive

te electrical products should not be disposed of with household waste. Please recycle where

as

W

facilities exist. Check with your Local Authority or retailer for recycling advice.

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK

email: [e-mail] - website: www.vax.co.uk