Vax U91-P3 Series Instruction Manual

www.vax.co.uk

Please read carefully before using this cleaner.

Always fully extend the mains cable before use.

Retain for future reference.

Vax careline

0870 6061248

instruction manual

Bagless upright

WARNING: This cleaner has a constantly

rotating brush bar which, when left in
contact with lino, parquet and other hard flooring
could potentially cause some damage to the floor
surface.

NOTE: Vax recommends that you raise the height
of the brush bar when using this cleaner on lino and
hard flooring. Vax cannot be held responsible for
damage to these surfaces if the customer fails to
take notice of this recommendation.

!

Vax model number:

U91-P3 Series

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 1

U91-P3

1. Diagram

www.vax.co.uk

2

parts overview

5

7

9

4

3

2

1

17

16

14

11

6

8

10

Fig.1/1

1 Handle

2 TurboTool holster

3 TurboTool

4 Dirt container release

5 Drt container handle

6 Dirt container lid

7 Filter

8 Dirt container

9 Carpet height adjuster

10 Brush bar

11 Dusting brush

12 Crevice tool and extension wand

13 Hose

14 Hose guides

15 Lower hose

16 Power on/off

17 Handle release

18 Wheels

14

18

15

13

12

WARNING: This cleaner has a

constantly rotating brush bar
which, when left in contact with lino,
parquet and other hard flooring
could potentially cause some
damage to the floor surface.

NOTE: Vax recommends that you
raise the height of the brush bar
when using this cleaner on lino and
hard flooring. Vax cannot be held
responsible for damage to these
surfaces if the customer fails to
take notice of this recommendation.

!

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 2

3

V

ax Careline 0870 606 1248

safety information

2. Safety Information

For Household Use Only

When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:

1. Only use the vacuum cleaner indoors on dry
surfaces.

2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.

3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.

4. Close attention is necessary when used by or near
children. Do not allow children to use as
a toy.

5. This appliance is not for use by persons (including
children) with reduced mental, physical or sensory
capabilities, or lack of experience or knowlegde,
unless they have been given supervision or
instruction concerning use of the appliance by a
person responsable for their saftey.

6. Use only as described in this manual. Use only the
manufacturer’s recommended attachments.

7. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified
person for examination, repair or adjustment.

8. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.

9. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.

10. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.

11. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.

12. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.

13. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.

14. Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).

15. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.

16. Do not use without the filters in place.

17. Take extra care when vacuuming on stairs.

18. Keep vacuuming area well lit.

19. Store the vacuum cleaner indoors in a cool, dry area.

20. Turn off the on/off switch before unplugging the
vacuum cleaner.

21. Use only CE-approved 13 amp extension cords. Non­approved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.

WARNING: Always switch off and unplug the

vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.

CAUTION: The vacuum cleaner is a very

powerful unit. Before plugging the cord into
the electrical outlet, make sure the switch is in the
‘off’ position. Hold the vacuum cleaner firmly when
starting and in use.

IMPORTANT: If the inlet or hose is blocked,

switch off the vacuum cleaner and remove the
blockage(s) before re-starting the vacuum cleaner.

IMPORTANT: Cleaning filters improves vacuum

performance.

This vacuum cleaner is intended for household use only
and not for commercial or industrial use.

Please keep these instructions for further use.

!!!

!

Motor Thermostat

IMPORTANT: The motor is equipped with a

thermal cut-out. If for any reason, the vacuum
cleaner should over-heat, the thermostat will
automatically turn the unit off. Should this occur,
unplug the vacuum cleaner from the electrical outlet
and turn off the switch. Remove the dirt container
and empty. Clean the filters. Allow the cleaner to cool
for approximately one (1) hour. To re-start, plug into
an electrical outlet and switch back on.

!

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 3

www.vax.co.uk

4

assembly

3. How to Assemble

IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before assembling or

removing the accessories.

Tool required: Phillips screwdriver

1. Place the base of the cleaner so it is facing away from

you. Position the body so that the lower hose is on your
right hand side. Push the body down into place.

To secure the body in place insert two screws supplied into
the back of the cleaner, through the hole located above
the hose guide (Fig.3/1).

2. With the cord clip on the handle facing you place it onto
the top of the body of the cleaner (Fig.3/2).

3. Push down firmly and line up the hole on the rear of the
handle. Insert lock piece into hole and screw into place
with the long screw (Fig.3/3).

4. Using the handle attach the main hose into the left
hand side of the cleaner. Press down firmly to secure in
place. The main hose can then be secured in the top and
side of the hose holder.

Push the dirt container lid firmly on top of the dirt
container and place it onto the cleaner. The canister lid will
snap into place in the body of the cleaner.

Attach the tools to the tool holder. The dusting brush fits
over a post at the back of the vacuum cleaner.

The crevice tool fits into the extension wand. The
extension wand is located on the right hand side (Fig.3/4).

5. Store the TurboTool in the caddy on the handle
(U91-P3P only) (Fig.3/5).

!

Phillips screwdriver required

Fig.3/1

Fig.3/2

Fig.3/3

Fig.3/5

Fig.3/4

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 4

5

V

ax Careline 0870 606 1248

operation / accessories

4. How to Operate

1. Plug the cord into an electrical outlet and turn on by
pressing the on/off pedal, located on the back left of the
cleaner (1).

To unlock the handle from the upright position press the
handle release pedal (2) down.

Move the handle to the desired position (a) for storage and
position (b) for normal operation. To clean under furniture,
press the release pedal again and use position (c) (Fig.4/1).

5. Accessories

NOTE: This unit is fitted with a constantly rotating
brush bar. To avoid damage to your carpet, ensure
the unit is not left on the stair tread when using the
accessories.

1. Make sure the vacuum cleaner has been switched off

and is in an upright position. Remove the lower hose by
twisting and pulling away from the side connector.

Remove the hose from the hose holder (Fig.5/1).

2. For hard to reach areas when additional hose length is
required, use the extension wand. It fits over the end of
the hose handle.

Choose the accessory that suits your need or use the hose
alone.

To fit the attachments push them firmly on to the end of
the extension wand or hose handle (Fig.5/2). To remove
the tool, twist and pull apart gently.

TurboTool

(U91-P3P only): Make sure the cleaner is turned

off before fastening TurboTool. Attach TurboTool to hose
end as all other accessories. For best pick up use
backward strokes on the surface being cleaned.

Fig.4/1

a

b

c

1

2

Fig.5/1

Fig.5/2

WARNING: This cleaner has a constantly

rotating brush bar which, when left in contact
with lino, parquet and other hard flooring could
potentially cause some damage to the floor surface.

NOTE: Vax recommends that you raise the height of
the brush bar when using this cleaner on lino and hard
flooring. Vax cannot be held responsible for damage to
these surfaces if the customer fails to take notice of
this recommendation.

!

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 5

www.vax.co.uk

6

dirt container & filter / belt & brush replacement

6. Dirt Container & Filter:
Removal and Replacement

1. Make sure the vacuum cleaner has been switched off
and unplugged from the mains supply. To remove the dirt
container from the vacuum cleaner press the release catch
and pull it forward.

To remove the lid of the dirt container hold the top and the
side handles firmly and turn the lid anti-clockwise. Pull the
lid away from the body of the dirt container.

Empty the all the dust and dirt from the dirt container
(Fig.6/1).

2. The filter inside the dirt container should be replaced
every 12 months. It should be cleaned each time the dirt
container is emptied. Remove it by grasping the ring at the
top of the filter.

Twist and pull the filter out.To clean it, tap it gently
against the side of a dustbin. Do not use a brush to clean
it as this may damage the filter.

Replace the filter into the dirt container. Push it firmly into
place to prevent dust and dirt leaking out. Replace the
canister lid turning clockwise and return the dust (Fig.6/2).

7. Belt and Brush:
Removal and Replacement

1. Unplug the vacuum cleaner from the mains supply.
Press the handle release button and turn the vacuum
cleaner over so that the base lies flat and face up. Use a
screwdriver to remove the four retaining screws shown
above.Remove the nozzle guard.

Lift and remove the brush bar, then slide the belt off the
motor shaft and dispose of it. Place a new belt on the
motor shaft and then slip the brush bar through the belt.

The belt should sit on the section of the brush bar without
bristles.. Re-fit the brush bar. Ensure the end caps are in
the correct position. Rotate the brush bar to check the belt
is not twisted. Replace the nozzle guard (Fig.7/1).

Fig.7/1

Fig.6/1

Fig.6/2

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 6

7

V

ax Careline 0870 606 1248

clearing blockages / troubleshooting

8. Clearing Blockages

WARNING: To reduce the risk of injury from
moving parts, unplug before servicing.

Clearing Blockages from the TurboTool

1. Turn the TurboTool/Power Brush over and slide off the
O-ring (Fig.8/1).

2. Pivot lowering housing and remove clog (Fig.8/2).

3. To re-assemble, be sure that the tabs are engaged. Pivot
the lower housing closed. Slip the O-ring into the groove at
the neck of the TurboTool/Power Brush to complete
reassumbly (Fig.8/3).

9. Troubleshooting

WARNING: To reduce the risk of personal injury,
unplug the vacuum cleaner before performing

maintenance or troubleshooting checks.

PROBLEM: Vacuum cleaner won't run

Cause: Not properly plugged into electrical outlet.

Solution: Plug in firmly.

Cause: Blown fuse/tripped breaker.

Solution: Reset circuit breaker or replace fuse.

Cause: Thermal cut out.

Solution: Refer to page 3 for information.

PROBLEM: Cleaner won’t pick up/loss of suction.

Cause: Lower hose not connected properly.

Solution: Refer to page 4 for fitting information.

Cause: Dirt container not installed correctly, or full.

Solution: Review dirt container replacement.

Cause: Broken or worn belt.

Solution: Replace the belt.

Cause: Clogged filters.

Solution: Remove, clean and replace filters.

Cause: Nozzle / hose or hose inlet is clogged.

Solution: Remove nozzle/hose and obstruction.

PROBLEM: Dust escaping from the vacuum cleaner.

Cause: Dirt container full.

Solution: Empty dirt container.

Cause: Dirt container not installed correctly.

Solution: Review dirt container replacement.

Cause: Hose not installed properly.

Solution: Review vacuum cleaner assembly.

!

‘O’ RING

Fig.8/1

Fig.8/2

TABS

Fig.8/3

!

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 7

www.vax.co.uk

8

uk service & help / technical specification

10. UK Service & Help

Vax Care 0870 6061248

Monday-Friday 8.00am to 8.00pm
Saturday-Sunday 9.00am to 5.00pm

Any queries or concerns about using the Vax, call the
Vax Careline. Calls are charged at the UK national rate.

Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.

www.vax.co.uk

11. Technical Specification

Voltage: 220-240V ~50Hz
Wattage: 1600W
Capacity: 2.4 litres
Filters: HEPA(

U91-P3)

HEPA, antibacterial (

U91-P3P)

Cord length: 6 m
Weight: 8 kg

Subject to technical change without notice.

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 8

9

V

ax Careline 0870 606 1248

This page has been left intentionally blank

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 9

This page has been left intentionally blank

www.vax.co.uk

10

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 10

11

V

ax Careline 0870 606 1248

This page has been left intentionally blank

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 11

---

EEC STATEMENT OF COMPLIANCE

Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the

U91-P3 series is manufactured in compliance with the following Directives:

Safety: 2006/95/EC Low Voltage Directive

EMC: 2004/108/EC Electromagnetic Compatibility Directive

Wasteelectrical products should not be disposed of with household waste. Please recycle where

facilities exist. Check with your Local Authority or retailer for recycling advice.

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK

email: [e-mail] - website: www.vax.co.uk

Vax U91-P3 User Guide.qxd:U91-P3 User Guide 15/12/08 09:34 Page 12