Vax U90-P5 Series, U90-P6 Series Instruction Manual

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 1

Vax Careline: (UK) 0844 412 8455

(ROI) 1-800 928 308

Bagless upright

Vax model number:

U90-P5 Series
U90-P6 Series

WARNING: This cleaner has a constantly

rotating brushbar which, when left in
contact with lino, parquet and other hard flooring
could potentially cause some damage to the floor
surface.

NOTE: Vax recommends that you raise the height
of the brushbar when using this cleaner on lino and
hard flooring. Vax cannot be held responsible for
damage to these surfaces if the customer fails to
take notice of this recommendation.

vax.co.uk

instruction manual

Version 1.2

Please read carefully before using this cleaner.

Always fully extend the mains cable before use.

Retain for future reference.

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 2

vax.co.uk

1. Diagram

1

2

3

4

5

6

7

8

9

10

Fig.1/1

PLEASE NOTE: some parts may vary according to model.
Please check inside flap of box for more details.

1 Handle

2 TurboTool caddy

3 TurboTool

(some models only)

4 Dirt container release

5 Drt container handle

6 Dirt container lid

7 Filter

8 Dirt container

9 Carpet height adjuster

10 Brush bar and brushbar windows

11 Dusting brush

12 Crevice tool and extension wand

13 Hose

14 Hose guides

15 Lower hose

16 Power on/off

17 Handle release

18 Wheels

11

12

14

14

16

17

13

15

18

WARNING: This cleaner has a

constantly rotating brushbar
which, when left in contact with lino,
parquet and other hard flooring
could potentially cause some
damage to the floor surface.

NOTE: Vax recommends that you
raise the height of the brushbar
when using this cleaner on lino and
hard flooring. Vax cannot be held
responsible for damage to these
surfaces if the customer fails to
take notice of this recommendation.

2

parts overview

!!!

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 3

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

2. Safety Information

For Household Use Only

When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:

1. Only use the vacuum cleaner indoors on dry
surfaces. Do not handle the plug or vacuum cleaner
with wet hands. Do not use outdoors or on wet
surfaces.

2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.

3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.

4. Children should be supervised to ensure that they
do not play with the appliance.

5. The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.

6. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.

7. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, it must be replaced by the manufacturer
or a recommended Service Agent to avoid hazard
and invalidating the guarantee.

8. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.

9. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.

10. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.

11. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.

12. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.

13. Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).

14. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.

15. Do not use without the filters in place.

16. Take extra care when vacuuming stairs.

17. Keep vacuuming area well lit.

18. Store the vacuum cleaner indoors in a cool, dry area.

19. Turn off the on/off switch before unplugging the
vacuum cleaner.

20. Use only CE-approved 13 amp extension cords. Non­approved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.

WARNING: Always switch off and unplug the

vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.

CAUTION: The vacuum cleaner is a very

powerful unit. Before plugging the cord into
the electrical outlet, make sure the switch is in the
‘off’ position. Hold the vacuum cleaner firmly when
starting and in use.

IMPORTANT: If the inlet or hose is blocked,

switch off the vacuum cleaner and remove the
blockage(s) before re-starting the vacuum cleaner.

IMPORTANT: Cleaning filters improves vacuum

performance.

This vacuum cleaner is intended for household use
only and not for commercial or industrial use.

Motor Thermostat

IMPORTANT: The motor is equipped with a thermal cut-

out. If for any reason, the vacuum cleaner should over­heat, the thermostat will automatically turn the unit off.
Should this occur, unplug the vacuum cleaner from the
electrical outlet and turn off the switch. Remove the dirt
container and empty. Clean the filters. Allow the cleaner
to cool for approximately one (1) hour. To re-start, plug
into an electrical outlet and switch back on.

Soft-start

IMPORTANT: All models are fitted with a soft-start

system. When the unit is switched on, the motor will take
a few seconds to build up to full power. The purpose of
this function is to offer better protection to the
vacuum motor.

safety information

3

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 4

vax.co.uk

3. How to Assemble

IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before assembling or
removing the accessories.

Tool required: Phillips screwdriver

1. Slide the back panel onto the base (Fig.3/1).

Fig.3/1

2. To secure, insert the two (2) screws into the front of the
back panel (Fig.3/2).

4. Place the upper handle onto the upright back panel
(Fig.3/4).

Fig.3/4

5. Insert locking part into slot (Fig.3/5).

Fig.3/5

6. Insert the screw into the back of the handle and screw
it into the locking part. Tighten until secure (Fig.3/6).

Back of

Fig.3/2

3. Slide the end of the lower hose onto the side connector
(Fig.3/3).

Fig.3/3

4

assembly

unit

Fig.3/6

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 5

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

7. Clip the TurboTool™ onto the front of the TurboTool™
caddy (Fig.3/7).

Fig.3/7

8. Wrap the hose around the back of the hose caddy. Push
the hose tube down into the right side of the cleaner to
secure (Fig.3/8).

Fig.3/8

9. Attach the tools. Slide the dusting brush onto the post
in the upper tool caddy with the bristles facing out
(Fig.3/9). Slide the extension tube/crevice tool into the
round opening on the front of the right side of the tool
caddy.

properly (Fig.3/10).

Fig.3/10

11. Insert the tab on the bottom of the dirt container into
the rectangular slot on the cleaner (Fig.3/11).

Fig.3/11

12. To secure the dirt container, push the top in place.
There will be an audible click when it is secure .

Fig.3/9

10. Ensure the filter is secure by pressing it firmly into its
holding in the bottom of the dirt container. Align the slots
on the lid with the tabs on the dirt container. Push the lid
down and twist clockwise. Use the arrow marked on the lid
to ensure that the dirt container and lid are aligned

assembly

5

!

!

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 6

vax.co.uk

4. How to Operate

Cord Release

Release the power cord by turning the quick cord release.
The cord should be inserted into the cord guide while
vacuuming to keep it out of the way.

Adjustment for Different Floor Types

Rotate the height adjust lever to match the surface being
cleaned (Fig.4/1).

Fig.4/1

NOTE: For easiest adjustment, place cleaner in full
upright position.

WARNING: This cleaner has a constantly

rotating brushbar which, when left in contact
with lino, parquet and other hard flooring could
potentially cause some damage to the floor surface.

NOTE: Vax recommends that you raise the height of
the brushbar when using this cleaner on lino and hard
flooring. Vax cannot be held responsible for damage to
these surfaces if the customer fails to take notice of
this recommendation.

CAUTION: The brushbar continues to rotate at

all times while the vacuum cleaner is on. Keep
hair, loose clothing, fingers and all parts of the body
away from the brush area while the vacuum cleaner
is on. The vacuum cleaner must be in the upright
position to lift the rotating brushbar off the carpet
when cleaning above the floor. Vax recommend that
the brushbar height adjust is turned to its highest
position when using the tools.

On/off Pedal

Plug the cord into the electrical outlet. Turn the vacuum
cleaner on by depressing the foot switch located on the
back left side of the vacuum cleaner (Fig.4/2A). The
vacuum cleaner can be turned off by pressing the on/off
switch again.

Handle Release Pedal

To release the handle, push the handle release pedal
located on the lower left side of the cleaner (Fig.4/2B).

A

B

Fig.4/2

Carpet Cleaning

Move the handle to the desired position for storage (A),
and normal operation (B). De-press the handle release
pedal again to clean under furniture (C) (Fig.4/3).

A

B

C

Fig.4/4

IMPORTANT: This vacuum cleaner is not

intended for use on hard floors. The powerful
rotating brushbar is designed to groom carpet pile and
could cause damage to some hard floor types.

6

operation

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 7

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

5. Accessories

IMPORTANT: The vacuum cleaner must be in the

upright position to raise the brushbar. The
brushbar height adjust must also be at its highest
position.

1. Remove the hose from the tool caddy (Fig.5/1).

Fig.5/3

Crevice tool: for crevices, corners and cracks etc.

Dusting brush: for delicate surfaces and skirting board.

Some models only)

Fig.5/1

2. Choose any of the handy on-board accessories or use
the hose alone. Simply push the attachment firmly onto
the end of the extension tube or hose handle. To remove
the accessory, twist and pull apart gently (Fig.5/2).

TurboTool:

hair and for stair and upholstery cleaning. Attach to hose
tube or extension tube as per all other accessories. For
best results, use backward strokes on the surface you are
cleaning.

Carry Handle

Use the carry handle on the back of the vacuum cleaner to

(

for excellent pick up of pet

Fig.5/2

Extension Tube

If additional length is needed, use the extension tube
and/or crevice tool. Pull the crevice tool out of the
extension tube or hose handle. To remove the tool, twist
and pull apart gently.

NOTE: The crevice tool is stored inside the extension
tube (Fig.5/3).

Carry

handle

Fig.5/4

move the cleaner from room to room (Fig.5/4).

NOTE: Check that the dirt container is securely in place
before lifting the vacuum cleaner.

accessories

7

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 8

vax.co.uk

6. Dirt Container & Filter:
Removal and Replacement

WARNING: To reduce the risk of injury from

moving parts, unplug before servicing.

NOTE: Unplug the vacuum cleaner before changing filter.

NOTE: For best performance, replace filter annually.
Cleaning the Central Filter

1. Press the latch above the dirt container and remove the
dirt container from the vacuum cleaner (Fig.6/1).

Fig.6/1

2. Remove the dirt container lid by turning it anti­clockwise (Fig.6/2).

Fig.6/2

3. Hold the dirt container and grasp the top of the filter.
Twist and pull the filter up and out (Fig.6/3).

4. Empty the dirt container completely (Fig.6/4).

Fig.6/4

5. Each time the dirt container is emptied, the filter should
be cleaned. Tap the filter against the side of a rubbish bin
until the dust stops falling from the filter. Return the filter
to the dirt container. Push the filter into place to prevent
dirt leakage (Fig.6/5).

Fig.6/5

6. Align slots on the lid with the tabs on the dirt container.
Push the lid down and twist clockwise.

NOTE: There is a guideline on the back of the dust
container lid. Align the tabs on the dirt container and
turn clockwise until secure.

7. Return the dirt container to the vacuum cleaner. Set the
aligning tab on the bottom of the dirt container into the
rectangular slot on the cleaner (inset). Push to click into
place (Fig.6/6).

Fig.6/3

8

dirt container & filter

Fig.6/6

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 9

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

7. Belt and Brush:
Removal and Replacement

1. Unplug the vacuum cleaner from the mains supply. Press
the handle release button and turn the vacuum cleaner
over so that the base lies flat and face up. Use a
screwdriver to remove the four retaining screws shown
above. Remove the nozzle guard (Fig.7/1).

Fig.7/1

Lift and remove the brushbar, then slide the belt off the
motor shaft and dispose of it. Place a new belt on the
motor shaft and then slip the brushbar through the belt
(Fig.7/2).

8. Clearing Blockages

WARNING: To reduce the risk of injury from
moving parts, unplug before servicing.

1. Check to see if dirt container is full. Empty and clean the
dirt container filter.

2. Unwrap the hose from the caddy. Remove any
obstruction if visible in the end of the hose (Fig.8/1).

Fig.8/1

2. Undo the hose from the back panel dirt tube. Remove
any obstruction (Fig.8/2).

Fig.8/2

3. To aid blockage removal, the hose can be removed by
pulling gently down and away from the body of the
machine.

Fig.7/2

The belt should sit on the section of the brushbar without
bristles. Re-fit the brushbar. Ensure the end caps are in the
correct position. Rotate the brushbar to check the belt is
not twisted. Replace the nozzle guard.

4. Push a broom handle or other similar implement through
the hose to clear any obstructions (Fig.8/3).

Fig.8/3

belt and brush / clearing blockages

9

LOCKING RING

TABS

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 10

vax.co.uk

5. Remove the nozzle guard by removing the four (4)
screws. Look for any obstructions and remove brushbar if
necessary (Fig.8/5).

Fig.8/5

Clearing Blockages from the TurboTool

Some models only)

(

Fig.8/6

3. Tore-assemble, be sure that the tabs are engaged. Pivot
the lower housing closed. Slip the locking ring into the
groove at the neck of the TurboTool™ to complete
reassembly (Fig.8/8).

Fig.8/8

Fig.8/7

1. Turn the TurboTool over and slide off the locking ring
(Fig.8/6).

2. Pivot lowering housing and remove clog (Fig.8/7).

10

clearing blockages

!

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 11

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

9. Troubleshooting

WARNING: To reduce the risk of personal injury,

unplug the vacuum cleaner before performing
maintenance or troubleshooting checks.

PROBLEM: Vacuum cleaner won't run

Cause: Not properly plugged into electrical outlet.

Solution: Plug in securely.

Cause: No electricity in the electrical outlet.

Solution: Check fuse or breaker.

Cause: On/off switch not turned on.

Solution: Push on/off switch to ‘on’.

Cause: Motor thermostat has tripped.

Solution: Switch off and unplug the vacuum cleaner.

Leave for one (1) hour before switching the
vacuum cleaner back on.

Cause: Blown fuse/tripped breaker.

Solution: Reset circuit breaker or replace fuse.

PROBLEM: Cleaner won’t pick up/loss of suction.

Cause: Full or clogged dirt container.

Solution: Clean dirt container.

Cause: Wrong pile height setting.

Solution: Adjust brushbar height.

Cause: Clogged nozzle.

Solution: Remove obstruction.

Cause: Clogged dirt inlet.

Solution: Remove power head cover and remove

obstruction.

Cause: Clogged hose.

Solution: Remove obstruction.

Cause: Broken belt.

Solution: Replace belt.

Cause: Hose not fully inserted.

Solution: Push hose in securely.

Cause: Dirty filters.

Solution: Clean/change filters.

PROBLEM: Accessories won’t pick up.

Cause: Accessories are not attached correctly.

Solution: Refer to page 7 for fitting information.

PROBLEM: Cleaner picks up moveable rugs or pushes
too hard.

Cause: Wrong brushbar height setting.

Solution: Adjust brushbar height setting.

PROBLEM: Brushbar does not turn.

Cause: Broken belt.

Solution: Replace belt.

Cause: Belt not installed correctly.

Solution: Check belt changing and brushbar cleaning.

PROBLEM: Air flow restricted with attachment use.

Cause: Attachment use restricts air flow.

Solution: Check attachment.

Cause: New carpet debris clogging air path.

Solution: Remove obstruction.

troubleshooting

11

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 12

vax.co.uk

10. UK Service & Help

(UK) 0844 412 8455
(ROI) 1-800 928 308

Monday-Friday 8.30am to 6.30pm
Saturday-Sunday 9.00am to 5.00pm

Any queries or concerns about using your Vax, call the
Vax Careline. Please make a note of the model number
and serial number of your Vax before calling. For the
nearest Vax Service Agent, please call the Vax Careline or
visit vax.co.uk

vax.co.uk

11. Consumables

To purchase spares and accessories, please visit vax.co.uk

HEPA filter kit (1-9-127361-00)

12. Technical Specification

Voltage: 230-240V ~50Hz
Wattage: 2000W/2200W
Capacity: 4.5 L (approx)

HEPA

HEPA anti-bacterial (some models only)
Cord length: 10 m (approx)
Weight: 8.4kg/8.65kg/8.9kg (varies per model)

Subject to technical change without notice.

12

uk service & help / technical specification

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 13

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

This page has been left intentionally blank

13

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 14

vax.co.uk

This page has been left intentionally blank

14

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 15

Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308

This page has been left intentionally blank

15

U90-P5 & U90-P6 Series User Guide v1.2.qxd:UG 13/5/10 14:46 Page 16

---

EEC STATEMENT OF COMPLIANCE

Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the Power 5 & Power 6

series bagless upright vacuum cleaners are manufactured in compliance with the following Directives:

Safety: 2006/95/EC Low Voltage Directive

EMC: 2004/108/EC Electromagnetic Compatibility Directive

Wasteelectrical products should notbe disposed of with household waste. Please recycle where

facilities exist. Check with yourLocal Authorityor retailerforrecycling advice.

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK

email: [e-mail] - website: vax.co.uk