DynamoPower
LET’S GET STARTED.
U85-DP-Be
U85-DP-Pe
U85-DP-Re
U85-DP-Te
Let’s talk safety
Basic
safety
precautions
Don’ts
Please keep instructions for further use and use only as instructed
in this guide.
This vacuum cleaner is intended for household use only and NOT
for commercial or industrial use.
• Only use the vacuum cleaner indoors on dry surfaces and keep
the area you’re cleaning well lit.
• Keep ngers, hair and loose clothing away from moving parts
and openings whilst using the vacuum cleaner.
• This vacuum cleaner can be used by children aged from 8 years
and above and persons with reduced physical, sensory or mental
• Don’t use this vacuum cleaner if it has been dropped,
damaged or left outdoors.
• Don’t run over the power cord or use vacuum cleaner if the power
cord or plug is damaged. Please contact our customer care line on:
0330 026 8455 (Mon-Fri 8:30am-6:30pm, Sat 9:00am-5:00pm).
• Don’t handle the plug or use the vacuum cleaner with wet hands.
• Don’t pull or carry this vacuum cleaner by the power cord.
• Don’t use the power cord as a handle, pull the power cord around
corners, sharp edges or close a door over the power cord.
• Don’t vacuum up any ammable or combustible materials (lighter
uid, petrol, kerosene etc.) or use the vacuum cleaner in an area
with explosive vapours or liquid.
Do’s
• Turn o all controls on the vacuum cleaner before disconnecting
or connecting the plug from the mains socket.
• Always keep the power cord away from the brushes during use.
After use always wrap the power cord around the cord
clips provided.
• Always make sure both the pre-motor/post-motor lters are
in place before use.
• Always ensure the brushbar is raised to the highest setting when
using the vacuum cleaner on the stairs and take extra care when
positioning the vacuum cleaner on the stairs.
Let’s talk safety
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the vacuum cleaner
in a safe way and understand the hazards involved. Children shall not play
with the vacuum cleaner. Cleaning and user maintenance shall not be made
by children without supervision.
• This vacuum cleaner is tted with a constantly rotating brush bar. To avoid
damage to your ooring, make sure the brush bar is raised to the highest setting
when using the accessories and when using on stairs.
• Only Vax recommend tools should be used with this vacuum cleaner,
use of non-branded Vax accessories/tools will invalidate your warranty.
• Don’t unplug vacuum cleaner by pulling on the power cord.
• Don’t vacuum up any ammable or combustible materials (lighter uid,
petrol, kerosene etc.) or use the vacuum cleaner in an area with
explosive vapours or liquid.
• Don’t vacuum up hot coals, cigarette butts, matches or smoking hot burning
items or use in an area where there may be harmful uids (chlorine, bleach,
and ammonia drain cleaner).
• Don’t attempt to remove blockages with sharp objects as this may cause damage
to the vacuum cleaner. Remove blockages only as instructed in this guide.
• Don’t vacuum up hard or sharp objects such as glass, nails, screws or coins etc.
• Don’t use the vacuum cleaner with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
• Always switch o the vacuum cleaner before disconnecting or connecting
the hose and accessories.
• Keep all openings clear and free from debris as this may aect the airow/suction.
• Always replace the fuse in the plug with a British 13amp fuse. Always protect
the power cable from heated surfaces and open ames.
• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat. Care should be taken to arrange the extension cord as it can
be a trip hazard.
• Store the vacuum cleaner in a cool, dry area. If lters have been cleaned as per
the user guide instructions ensure they are thoroughly dry before storing away.
Thank you for buying this Dynamo Power.
Taking care of your carpets and hard oors
The Dynamo Power is designed to make vacuuming carpets and hard oors regularly,
as eective and ecient as possible and this user guide will help you get the most out
of your machine.
Maintaining your carpets and hard oors will ensure they keep their appearance for longer.
You’ve chosen the carpets and hard oors for your home for a reason and Vax will help
you take good care of them.
Taking care of your Dynamo Power
Also inside this guide are instructions on maintaining your new machine, so that it’s always
ready when you are to tackle your carpets and hard oors.
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support
Let us know what you think @VaxUK
Contents
Let’s talk safety
Dynamo Power
(Included in all models)
Included with
your machine
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
What to do if it goes wrong
Getting in touch
Accessories
3-in-1 Tool (Crevice, Dust
and Upholstery Tool)
Pre-motor Filter
Post-motor Filter
Hard Floor Adaptor
Dynamo Power Pet
TurboTool
Initial Setup for normal operation
1. Use the base accessories.
– Shortest hose
– Extension tube set to shortest practicable length.
2. Clean lters installed.
3. Dust receptacle empty.
4. All Bleeds must be closed.
5. Floor heads/tools set to Carpet Mode for carpet cleaning.
6. Mechanical Agitation turned ON for carpet cleaning.
7. Floor heads/tools set to Hard Floor Mode for hard oor cleaning.
8. Mechanical Agitation turned OFF for hard oor cleaning.
Dynamo Power Reach
Longer power cord
Dynamo Power
Total Home
Up-top Tool
Tool Connector
Getting to know your machine
Handle
TurboTool holder (not shown)
Extension tube
(hidden)
Dirt container
release button
Separator
Dirt container
Post-motor lter cover
Hose to
machine
connector
Power
On/O button
Handle release button
Quick release
cord hook
Power cord
Hose
Floor type
adjustor
Technical Specication
Name Dynamo Power
Voltage Please refer to product rating label
Wattage Please refer to product rating label
Cord length 7-10m
Weight 6kg
Subject to technical change without notice.
Accessories & Consumables
Filter Kit (Type 98)*
1-1-134233-00
Belt Kit (Type 1)*
1-1-130669-01
TurboTool (Type 6)*
1-1-134419-00
*To purchase consumables and accessories, please visit vax.co.uk
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Assembling your upright
Getting started
Insert the back panel into
the oorhead.
Place the dirt container onto
the machine and push until it
clicks into place.
Insert the lower quick release
cord hook into the hole at the
bottom of the back panel.
Insert the extension tube into
the handle.
If your model comes with a TurboTool
Now take the small clip and
push it down between the
post-motor lter cover and
back panel, over the quick
release cord hook to lock
into place.
Push handle into the top of
the machine until it clicks
into place.
Insert the end of the hose
into the tube at the back of
the machine and connect the
hose end to the oorhead.
Push TurboTool holder on to
the handle.
Clip TurboTool into position.
Using your machine
Before you begin cleaning
• Always switch o and unplug the vacuum cleaner before connecting or disconnecting the hose/attachments, or removing and
emptying the dirt container.
• The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat the thermostat
will automatically turn the vacuum cleaner o. If this happens, switch the vacuum cleaner o and unplug from electrical
socket. Remove and empty the dirt container also check the vacuum cleaner for blockages. Allow the vacuum cleaner to cool
for approximately 1 hour (if you have cleaned the lters please wait 24 hours for the lters to fully dry before putting back into
the vacuum).
• For best cleaning results, lters should be tapped over a bin every 4-6 uses to remove dirt and debris and washed
every 3 to 6 months (depending on the level of use).
• If the vacuum cleaner is blocked, switch o and unplug before removing the blockage.
• When using the accessories always make sure the brushbar is raised to the highest setting.
IMPORTANT: When the vacuum cleaner is stood in the upright position or when using on stairs and the hose/tools,
the brushbar height adjust dial must be set to hard oor.
How to use
Twist the quick release
cord hook to release the
power cord.
Choose your desired carpet
height or hard oor setting.
Using the Hard Floor Adaptor
Apply the Hard Floor Adaptor for optimum results on hard oors.
The Hard Floor Adaptor can be used on any oor setting.
Lie vacuum cleaner on its
back exposing brushbar.
Align Hard Floor Adaptor
with base of vacuum
cleaner, push until its clicks
into place.
Plug in your machine and
push On/O button to
switch on.
Don’t over ll the dirt
container to avoid clogging
your lter.
To ensure the Hard
Floor Adaptor is
correctly tted,
the wheels should
be towards the back
of the oor tool
when attached to
vacuum cleaner.
TIP
Using accessories
Remove hose end from
the oorhead.
Choose an accessory.
“turbo tool some
models only”.
Extension tube
Remove extension tube
from inside the handle.
Turn the extension tube and
attach to the handle.
Using your machine on the stairs
Hold the machine to steady
when using on the stairs.
Always make sure the
brushbar is overhanging the
stair tread during use.
Attach accessory adapter to
hose end.
Attach hose to the top of
the handle.
If required use
tool connector.
Push accessory on to the
extension tube.
This machine
has a constantly
rotating brushbar.
When using the machine
on stairs, ensure the
height adjuster dial is set
to hard oor and the
brushbar is overhanging
the stair tread (as pictured). Always take extra
care when cleaning stairs.
CAUTION
Taking care of your machine
24hr
Emptying and cleaning the dirt container
Press dirt container
release button to remove
the dirt container.
Hold dirt container over
a bin and unclip the lock
on the bottom of the dirt
container, allowing the dirt
to fall out.
Cleaning the pre-motor lter
Turn the dirt container
lid anti-clockwise.
Lift the dirt container lid
to remove.
40˚C
MAX
Close the base of the dirt container, align the
dirt container base back onto the machine
and push until it clicks back into place.
Lift to remove the
pre-motor lter
Tap the lter over a bin to
remove any dirt/debris
Wash the lter under
running water (40°C max).
Leave to fully dry for at
least 24 hours before
placing back in
the machine.
Wash lters with warm
water (MAX 40°C)
at least every
3 months.
TIP
Cleaning the shroud
Taking care of your machine
Turn the dirt container
lid anti-clockwise and lift
to remove.
Remove the pre-motor lter
to allow access to
the shroud.
Post-motor lter maintenance
Twist post-motor lter
cover anti-clockwise and lift
to remove.
Remove the lter. Check the post-motor lter
Removing debris from the brushbar
Tap the shroud over a bin to
remove dirt and debris.
for discolouration.
Using a soft brush or dry
cloth wipe the remaining
dirt /debris from the shroud
Using a pair of scissors cut any hair or debris free
from around the brushbar.
Always switch the
machine o
and unplug before
carrying out
any maintenance.
CAUTION
Let’s talk technical
Removing blockages from the TurboTool (some models only)
Remove the rubber ring.
Changing the belt
Push both buttons to open the TurboTool.
Using a pair of scissors, cut
any hair or debris free from
around the brushes.
Switch o your vacuum
cleaner at the main socket
and unplug. Unclip the 2
small wheels from the base
of the vacuum to enable you
to remove the screws from
behind. Note: The screw for
the height adjuster dial is
located here.
Remove the 9 screws
from the base of the
oorhead cover.
If the hose or telescopic
tube is blocked, switch o
the vacuum cleaner and
remove the blockage(s)
before re-starting the
vacuum cleaner.
CAUTION
Remove the oorhead cover.
Lift the brushbar from the
machine to remove the
belt. Remove and dispose
of the old belt. Remove
any threads or hair caught
around the brushbar
Clean any debris from the
spindle and place the new
belt onto the brushbar and
hook onto the spindle.
Once the belt has been
replaced attach the
brushbar back onto the
vacuum.
Replace the oorhead
cover, 2 small wheels and
height adjuster dial by
screwing back into place.
There is an
accessory missing
What to do if it goes wrong
SolutionProblem
• Check the ‘This pack contains’ panel on the box to make sure the part
is included with your machine.
• The plug may not be fully pushed into the electrical socket.
Why does my
vacuum cleaner
have no power?
Why won’t the vacuum
cleaner pick up?
My brushbar
isn’t turning
• Check the fuse in the plug if this needs replacing, always replace with
a British 13amp fuse.
• The motor thermostat may have tripped. If this has happened, unplug
the vacuum cleaner. Remove and empty the dirt container and check
the hose for blockages.
• Clean the lters and allow the vacuum cleaner to cool for
approximately 1 hour (if you have washed the lters you will need to
wait 24 hours for the lters to fully dry before putting them back into
the vacuum cleaner).
• There may be a blockage in the hose. Please remove the hose from the
vacuum cleaner, check and clear any blockages.
• Empty the dirt container and clean lters.
Go to the ‘Taking care of your machine’.
• The brushbar may not be turning. Go to my brushbar isn’t turning below.
• If the accessory/tool will not pick up, check and clear any blockages.
• The brushbar may be clogged, check the brushbar and clear any hair
or debris. Go to ‘Let’s talk technical’.
• The belt may be broken. Go to ‘Let’s talk technical’.
IMPORTANT: To reduce the risk of personal injury, unplug the vacuum before performing maintenance
/troubleshooting checks.
Getting in touch
†
Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
Accessories
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
TurboTool (Type 6)
1-1-134419-00
Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking up
stubborn pet hair.
3-in-1 Tool
1-1-129167-00
3-in-1 tool includes crevice tool for awkward areas
and corner, dusting brush for areas such as skirting
and an upholstery tool for cleaning sofas, curtains,
chair seats and car interiors.
Flexi-crevice Tool
1-1-131393-00
A handy long, exible tool for getting far behind and
around furniture.
Fur ‘n’ Flu Tool
1-1-131392-00
Specically designed to remove extra stubborn pet
hair from upholstery, furniture and carpets.
GET IN TOUCH
0330 026 8455 VaxVacuumsinfo@vax.co.uk vax.co.uk @Vax UK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
U85-DP-(Be/Pe/Re/Te) is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
© 2015 All rights reserved. VAX®, VAX Lozenge, are trade marks or registered trade marks of Techtronic Floor Care
Technology Ltd.
Loading...