Power
POWERFUL PERFORMANCE
LET’S GET STARTED.
U84-M1-Be
U84-M1-Pe
U84-M1-Re
U84-M1-Te
Let’s talk safety
Basic
safety
precautions
Don’ts
• This vacuum cleaner is intended for household use only and
NOT for commercial or industrial use.
• Only use the vacuum cleaner indoors on dry surfaces and
keep the area you’re cleaning well lit.
• Keep ngers, hair and loose clothing away from moving parts
and openings whilst using the vacuum cleaner.
• This vacuum cleaner can be used by children aged from 8
years and above and persons with reduced physical, sensory
• Don’t use the vacuum cleaner if it has been dropped, damaged
or left outdoors.
• Don’t run over the power cord or use vacuum cleaner if the
power cord or plug is damaged. Please contact our Customer
Service Line on: 0330 026 8455 (Mon-Fri 08:30-18:30 Sat
09:00-17:00).
• Don’t handle the plug or use the vacuum cleaner with wet hands.
• Don’t pull or carry the vacuum cleaner by the power cord.
Don’t use the power cord as a handle, pull the power cord around
corners, sharp edges or close a door over the power cord.
Don’t unplug the vacuum cleaner by pulling on the power cord.
Do’s
• Turn o all controls on the vacuum cleaner before
disconnecting or connecting the plug from the mains socket.
• Always keep the power cord away from the brushes during
use. After use always wrap the power cord around the cord
clips provided.
• Always make sure both the pre-motor/post-motor lters are
in place before use.
• This vacuum cleaner is tted with a constantly rotating
brushbar. To avoid damage to your ooring, make sure the
brush bar is raised to the highest setting when using the
accessories and when using on stairs.
• Always take extra care when positioning the vacuum cleaner
on the stairs.
or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the vacuum cleaner in a
safe way and understand the hazards involved. Children shall not play with
the vacuum cleaner. Cleaning and user maintenance shall not be made by
children without supervision.
• Only Vax recommended tools should be used with the vacuum cleaner,
use of non-branded Vax accessories/tools will invalidate your warranty.
• Don’t vacuum up any ammable or combustible materials (lighter uid, petrol,
kerosene etc) or use the vacuum cleaner in an area with explosive vapours
or liquid.
• Don’t vacuum up hot coals, cigarette butts, matches or smoking hot burning
items or use in an area where there may be harmful uids (chlorine, bleach,
and ammonia drain cleaner).
• Don’t attempt to remove blockages with sharp objects. This may cause damage
to the vacuum cleaner, remove blockages only as instructed in this guide.
• Don’t vacuum up hard or sharp objects such as glass, nails, screws or coins etc.
• Don’t use the vacuum cleaner with incorrect voltage as this may result in
damage or injury to the user. The correct voltage is listed on the ratings label.
• Always switch o the vacuum cleaner before disconnecting or connecting
the hose and accessories.
• Keep all openings clear and free from debris as this may aect the
airow/suction.
• Always replace the fuse in the plug with a British 13amp fuse. Always protect
the power cable from heated surfaces and open ames.
• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat. Care should be taken to arrange the extension cord as it can
be a trip hazard.
• Store the vacuum cleaner in a cool, dry area. If the lters have been cleaned
as per user the guide instructions ensure they are thoroughly dry before
storing away.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE.
Thank you for buying this Power vacuum
Taking care of your carpets and hard fl oors
The Power is designed to make vacuuming carpets and hard oors regularly, as e ective
and effi cient as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets and hard oor will ensure they keep their appearance for longer.
You’ve chosen the carpets and hard oors for your home for a reason and Vax will help you
take good care of them.
Taking care of your Power
Also inside this guide are instructions on maintaining your new machine, so that it’s always
ready when you are to tackle your carpets and hard oors.
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support
Let us know what you think @VaxUK
Contents
Let’s talk safety
Power
Included with
your machine
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
Accessories
What to do if it goes wrong
Getting in touch
2-in-1 tool
Hard Floor Adaptor
Power Pet/Reach
Includes all the above, plus
TurboTool
Power Total Home
Includes all the above, plus
Up-Top-Tool
Notes
Handle
Flat Upholstery Tool
Getting to know your machine
Hose guide
Stretch hose
Dirt container release button
Cord hook
Separator
Dirt container
Cord hook
Post motor lter
and cover
Height adjuster
dial
Brushbar
Technical Specifi cation
Name Power
Voltage 220-240V~50Hz
Wattage 850W
Cord length 6-8m
Weight 6.1kg
Subject to technical change without notice.
Handle release clip
Hose guide
Accessory hose
On/O pedal
Accessories & Consumables
Pre-motor Filter
1-7-137046
Post-motor Filter
1-7-137047
Pro Cleaning Kit (Type 2)
1-1-133326-00
TurboTool (Type 5)
1-1-134418-00
To purchase consumables and accessories, please visit vax.co.uk
Flat Upholstery Tool
1-1-131394-00
Flexi Crevice Tool (Type 2)
1-1-131393-00
2 in 1 Tool (Type 3)
1-1-132332-00
Getting started
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Before you begin
WARNING: Always switch o the vacuum cleaner before connecting or disconnecting the hose/attachments
or removing and emptying the dirt container.
IMPORTANT: The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does
overheat the thermostat will automatically turn the vacuum cleaner o . If this happens switch the vacuum cleaner o
and unplug from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for blockages.
Allow the vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please wait 24 hours for the
lters to fully dry before putting back into the machine).
For best cleaning results, lters should be tapped over a bin every 4-6 uses to remove dirt and debris and washed every
3 to 6 months (depending on the level of use).
If the vacuum cleaner is blocked, switch o and unplug before removing the blockage.
When the vacuum cleaner is stood in the upright position, or when using the hose and tools the brushbar height adjuster
must be set to the highest setting.
Assembling your vacuum cleaner
Press the release clip on
the stretch hose, line up
and push the hose into
the handle.
Slide the handle down
into the main body of
the vacuum cleaner.
Line up the stretch hose with hose
guides, push and clip stretch hose
into place. The end of the stretch
hose will hang loose at the bottom
of the machine
Using your machine
IMPORTANT: Always switch o the vacuum cleaner before disconnecting or connecting the hose and accessories.
The accessories can be attached to the handle or directly to the hose.
When using accessories on the hose/handle raise the height adjuster to the highest setting.
Plug vacuum cleaner into
the mains and switch on.
Using the hard fl oor tool
Lie vacuum cleaner on its
back exposing the brush bar.
Turn height adjuster dial
to desired setting.
Line up oor tool with the base of the vacuum cleaner, push until it clicks into place.
Place foot on oorhead
and pull handle to recline.
Press the on/o pedal
to switch on.
To make sure the oor
tool is correctly tted,
the wheels should
be towards the back
of the oor tool
when attached to
vacuum cleaner.
TIP
Using your machine
IMPORTANT: Always switch o the vacuum cleaner before disconnecting or connecting the hose and accessories.
The accessories can be attached directly to the hose.
This vacuum cleaner is tted with a constantly rotating brush bar. To avoid damage to your ooring, make sure the brush
bar is raised to the highest setting when using the accessories.
Using the hose and accessories
Pull and release the stretch
hose from hose guides.
Push and attach the 2-in-1
crevice/dusting brush,
TurboTool or Above Floor
Tool (some models only)
onto the end of the
stretch hose.
Unclip the hose end on
the accessory hose. Pull
and remove accessory
hose from the base of
vacuum cleaner.
Turn the brushbar height
adjuster dial to highest
setting before pressing the
on/o pedal to switch the
vacuum on.
Line up and push the end
of the stretch hose onto
the accessory hose until
it clicks into place.
Press the release clip
on the stretch hose,
pull and remove stretch
hose from handle.
Using your machine
IMPORTANT: Always switch o the vacuum cleaner before disconnecting or connecting the hose and accessories.
This vacuum cleaner has a constantly rotating brush bar. When cleaning on stairs raise the height adjuster dial to the
highest setting. The brush bar must over hang the stair tread.
Always take extra care when cleaning stairs.
Using the handle and accessories
Pull and release the stretch
hose from hose guides.
Press the handle release
clip, pull and remove the
handle out of the main body.
Unclip the hose end on the
accessory hose. Pull and remove
accessory hose from the base of
vacuum cleaner.
Attach the 2-in-1 crevice/
dusting brush to the end
of the handle.
Line up and push the end of the
stretch hose onto the accessory
hose until it clicks into place.
Turn brush bar height adjuster
dial to highest setting before
pressing the on/o pedal to
switch the vacuum on.
Taking care of your machine
24hr
IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the machine should overheat, the
thermostat will automatically turn the machine o . Switch o and unplug the vacuum cleaner. Check the machine for
blockages and clean the lters . Wash the lters with warm water (40°C max) and leave for 24 hours or until fully dry
before replacing into the machine.
For best cleaning results, lters should be tapped over a bin every 4-6 uses to remove dirt and debris and washed
every 3 to 6 months (depending on the level of use).
Don’t use your vacuum cleaner without all of the lters in place.
Emptying the dirt container
Press the dirt container
release button, pull and
remove the dirt container.
Don’t over ll the dirt container to avoid blocking the air ow through the vacuum cleaner and replace lters
every 6-9 months.
Hold the dirt container
over a bin.
Press the dirt release clip,
allowing dirt/debris to fall out.
Cleaning the pre-motor fi lter
Turn the dirt container
lid anti-clock wise , lift
and remove the lid
from dirt container.
Pull the lter tab and
remove the pre-motor lter.
Tap the lter over a bin
to remove any dirt/debris.
Wash the lter under running
water (40°C max).
Leave for 24hrs or until
fully dry before replacing.
TIP
24hr
Taking care of your machine
Cleaning the separator
Turn the dirt container
lid anti-clock wise , lift
and remove the lid from
dirt container.
Tap the separator over a bin
to remove any dirt/debris.
Pull the lter tab and remove
the pre-motor lter.
Using a dry cloth wipe the
remaining dirt /debris from
the shroud.
Lift the separator out
of the dirt container.
Re t the separator making
sure both rectangular holes
in the dirt container and
separator line up.
Post-motor fi lter maintenance
The post-motor lter is designed to o er long life with no maintenance. The lter should be checked periodically and
when heavily discoloured it should be replaced. Please do not wash, scrub or brush the lter as this will damage the lter.
Press the release clip
on the post-motor lter
cover, pull to remove
cover then pull and
remove post-motor lter.
Check the post-motor lter
for any discolouration.
Don’t use your vacuum
cleaner without all of the
lters in place.
CAUTION
Let’s talk technical
IMPORTANT: Unplug and switch o vacuum cleaner before performing maintenance or troubleshooting checks.
Removing debris from the brushbar
Using a pair of scissors
remove any threads or
hair caught around the
brush bar.
Removing blockages from the TurboTool
Slide the locking ring
to remove.
Lift and separate the
housing. Using a pair
of scissors remove any
threads or hair caught
around the brushbar.
Removing a blockage from the hose
Press the release clip
on the stretch hose, pull
and remove hose from
the handle.
Insert a broom handle or
similar blunt instrument into
the hose to remove blockage.
Line up the tabs on front
of housing and re- t.
Slide locking ring into
groove to secure.
To test for a blockage
in hose, drop a small
ball of paper through
the hose. The paper
will drop through
if the hose is clear.
TIP
Let’s talk technical
IMPORTANT: If the brushbar does not rotate easily then the belt may not have been tted correctly. Make sure
the belt is not twisted.
Replacing the belt
Switch o your vacuum
cleaner at the main socket
and unplug. Unclip the
2 small wheels from the
base of the vacuum to
enable you to remove
the screws from behind.
Note: The screw for the
height adjuster dial is
located here.
Remove the 9 screws
from the base of the
oorhead cover.
Remove the
oorhead cover.
Lift the brushbar from the
machine to remove the
belt. Remove and dispose
of the old belt. Remove
any threads or hair caught
around the brushbar
Clean any debris from
the spindle and place
the new belt onto the
brushbar and hook
onto the spindle.
Once the belt has been
replaced attach the
brushbar back onto
the vacuum.
Replace the oorhead
cover, 2 small wheels
and height adjuster dial by
screwing back into place.
Accessories
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
Pro cleaning kit
1-1-133326-00
All our best tools all in one kit that makes cleaning
your home quicker, easier and with even better results.
We’ve taken care of cleaning all of the hard to reach
areas such as on top of cupboards and in between
blinds to the dust that collates behind and
within the radiator.
Flexi Crevice Tool
1-1-131393-00
A handy long, exible tool for getting far behind and
around furniture.
TurboTool (Type 5)
1-1-134418-00
Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking up
stubborn pet hair.
Flat Upholstery Tool
1-1-131394-00
Cleans large areas of upholstery like sofas and
curtains, quickly and e ectively.
3-in-1 Tool
1-1-129167-00
3-in-1 tool includes crevice tool for awkward areas
and corners, dusting brush for areas such as
skirting and an upholstery tool for cleaning sofas,
curtains, chair seats and car interiors.
What to do if it goes wrong
Is there an
accessory missing?
Why does my vacuum
cleaner have no power?
SolutionProblem
• Check the ‘This pack contains’ panel on the box to make sure
the part is included with your vacuum cleaner.
• The plug may not be fully pushed into the electrical socket.
• Check the fuse in the plug if this needs replacing, always replace with
a 13amp fuse.
• The motor thermostat may have tripped. If this has happened, unplug
the vacuum cleaner. Remove and empty the dirt container and
check the hose for blockages. Clean the lters and allow the vacuum
cleaner to cool for approximately 1 hour (if you have washed the
lters you will need to wait 24 hours for the lters to fully dry before
putting them back into the vacuum cleaner).
Why won’t the vacuum
cleaner pick up?
Why isn’t the
brushbar turning?
• Empty the dirt container and clean lters. Go to ‘Taking care of your
machine’.
• There may be a blockage in the hose. Remove the hose from the
vacuum cleaner, check and clear any blockages. Go to ‘Let’s talk
technical’.
• The brushbar may not be turning. Go to ‘My brushbar isn’t turning’ below.
• The brushbar height adjuster dial may not be set to the correct setting.
Go to ‘Using your machine’.
• Make sure the hard oor adaptor is attached/unattached dependant
on the oor surface.
• If the accessory/tool will not pick up, check and clear any blockages.
Go to ‘Let’s talk technical’.
• The brush bar may be clogged, check the brushbar and clear
any hair or debris Go to ‘Let’s talk technical’.
• The belt may be broken, Go to ‘Let’s talk technical’.
Getting in touch
†
†
Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
Notes Notes
GET IN TOUCH
0330 026 8455 VaxVacuumsinfo@vax.co.uk vax.co.uk @Vax UK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
U84-M1-(Be/Pe/Re/Te) manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage Directive.
EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
© 2015 All rights reserved. VAX®, VAX Logo, are trade marks or registered trade marks of Techtronic Floor Care Technology Ltd.
Loading...