Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using
the cleaner. Always fully extend
the mains cable before use.
www.vax.co.uk
BAGLESS UPRIGHT VACUUM CLEANER
Vax Model Number: VS-19TLT
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 2
1. Diagram
P
arts Overview
1
1
4
5
6
9
11
8
7
2
17
18
19
20
16
18
2
0
2
0
15
14
FRONT
BACK
13
12
2
1 Handle
2 Dirt container release latch
3 Dirt container
4 Lower hose
5 Clear window
6 Bumper bar
7 Filter
8 Dirt container lid
9
Main hose
10 Cord clip
11 Extension wand
12 Carrying handle/ Cord wrap
13 On/Off pedal
14 Handle release pedal
15 Cord wrap with quick release
16 Power cord
17 Crevice tool
18 2-in-1 Tool - Dust brush/ Upholstery tool
19
Hose bracket
20 TurboTool
3
10
Fig.1/1
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 3
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting to or disconnecting from the mains
supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose.
4. Close attention is necessary when used by or near
children. Do not allow children to use as a toy.
5. Use only as described in this manual. Use only
the manufacturer’s recommended attachments.
6. Do not use the vacuum cleaner with a damaged
cord or plug. Do not use the vacuum cleaner if it
has been dropped, damaged, left outdoors or
dropped into water. Return the vacuum cleaner to
a Vax Authorised Service Agent or suitably
qualified person for examination, repair or
adjustment.
7. Do not pull or carry by the cord. Do not use the
cord as a handle, close a door on the cord or pull
the cord around sharp edges or corners. Do not
run the vacuum cleaner over the cord. Keep the
cord away from heated surfaces.
8. Do not handle the plug or vacuum cleaner with
wet hands. Do not use outdoors or on wet
surfaces.
9. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
11. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking or burning objects.
12. Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene, etc) or
use in the presence of explosive liquids or
vapours.
13. Do not vacuum up harmful or toxic material
(chlorine bleach, ammonia, drain cleaner, etc).
14. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.
15. Do not use without the filters in place.
16. Use extra car
e when vacuuming on stairs.
17. Keep vacuuming area well lit.
18. Store the vacuum cleaner indoors in a cool,
dry area.
19. Turn off the switch before unplugging.
20. Use only CE-approved 13 amp extension cords.
Non-approved extension cords may overheat.
Care should be taken to arrange the cord so that
the cord cannot be pulled or tripped over.
WARNING: Always switch off and unplug the vacuum
cleaner from the electrical outlet before assembling,
opening or emptying the dirt container, or before
connecting/disconnecting the attachments.
CAUTION: The vacuum cleaner is a very powerful unit.
Before plugging the cord into the outlet make sure the
switch is in the ‘off’ position. Hold the vacuum cleaner
firmly when starting and in use.
IMPORTANT: If the inlet or hose is blocked, switch off
the vacuum cleaner and remove the blockage(s)
before re-starting the vacuum cleaner.
IMPORTANT: Cleaning filters improves vacuum
performance. Make sure all filters are replaced back
into the vacuum cleaner before using.
This vacuum cleaner is intended for household use
only and not for commercial or industrial use.
PLEASE KEEP THESE INSTRUCTIONS FOR
FURTHER USE.
S
afety Information
Motor Thermostat
IMPORTANT: The motor is equipped with a thermal
cut-out. If for any reason, the vacuum cleaner
should over-heat, the thermostat will automatically
turn the unit off. Should this occur, unplug the
vacuum cleaner from the electrical outlet and turn
off the switch. Remove the dirt container and empty.
Clean the filters. Allow the cleaner to cool for
approximately one (1) hour. To re-start, plug into an
electrical outlet and switch back on.
3
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 4
H
ow to Assemble / How to Operate
4
3. How to Assemble
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before assembling or
removing the accessories.
1. Place the base of the cleaner so it is facing away
from you. Position the body so that the lower hose is
on your right hand side. Push the body down into
place.
To secure the body in place insert one of the screws
supplied into the back of the cleaner, through the hole
located above the on/off pedal.
Pull back the flap on the clear window. Match the slots
on the hose to the tabs on the hose inlet. Push down
firmly on the cuff and turn anti-clockwise to lock in
place (fig. 3/1).
2. Align the holes in the tool holder, with the holes on
top of the body. Use two of the screws supplied to
secure the tool holder in place.Do not over
tighten.With the hose clip on the handle facing you
place it onto the top of the body of the cleaner (fig. 3/2).
3. Push down firmly and line up the screw hole on the
rear of the handle.
Use one of the screws supplied to secure the handle
on the body.
Insert the small end of the main hose into the tool
holder on the right hand side (fig. 3/3).
4. Using the handle attach the main hose into the left
hand side of the cleaner. Press down firmly to secure
in place. The main hose can then be secured in the
top and side of the tool holder.
Push the dirt container lid firmly on top of the dirt
container and place it onto the cleaner. The canister lid
will snap into place in the body of the cleaner.
Attach the tools to the tool holder. The 2 in 1 tool fits
over a post at the back of the vacuum cleaner.
The crevice tool fits into a round slot on the rear right
hand side of the tool holder. The extension wand hose
on the left hand side (fig. 3/4).
4. How to Operate
1. Plug the cord into an electrical outlet and turn on by
pressing the on/off pedal, located on the back left of
the cleaner.
To unlock the handle from the upright position press
the handle release pedal down.
Move the handle to the desired position (A) for storage
and position (B) for normal operation. To clean under
furniture, press the release pedal again and use
position (C) (fig. 4/1).
Fig.3/4
Fig.3/1
Phillips screwdriver required
Fig.3/3
A
B
C
Fig.3/2
Fig.4/1
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 5
A
ccessories/Dirt Container & Filter: Removal & Replacement/Belt or Brush removal and replacement
5
5. Accessories
1. Make sure the vacuum cleaner has been switched
off and is in an upright position. Remove the lower
hose by twisting clockwise and pulling away from the
base of the cleaner.
Remove the hose from the tool holder.
Slide the hose into the lower hose with the tab facing
upwards twist together to secure (fig. 5/2).
2. For hard to reach areas when additional hose length
is required, use the extension wand. It fits over the end
of the hose.
Choose the accessory that suits your need or use the
hose alone.
To fit the attachments push them firmly on to the end of
the extension wand or hose. To remove the tool, twist
and pull apart gently.
When moving from one room to another use the carrying
handle at the rear of the vacuum cleaner (fig. 5/1).
6. Dirt Container & Filter: Removal and
Replacement
1. Make sure the vacuum cleaner has been switched off
and unplugged from the mains supply. To remove the
dirt container from the vacuum cleaner press the release
catch and pull it forward.
To remove the lid of the dirt container hold the top and
the side handles firmly and tur
n the lid anti-clockwise.
Pull the lid away from the body of the dirt container.
Empty all of the dust and dirt from the dirt container
(fig. 6/1).
2. The filter inside the dirt container should not need
replacing but it should be cleaned each time the dirt
container is emptied. Remove it by grasping the ring at
the top of the filter.
Twist and pull the filter out.To clean it, tap it gently against
the side of a dustbin. Do not use a brush to clean it as
this may damage the filter. Do not wash the filter.
Replace the filter into the dirt container. Push it firmly into
place to prevent dust and dirt leaking out. Replace the
canister lid turning clockwise and return the dust
(fig. 6/2).
7. Belt & Brush: Removal and
Replacement
1. Unplug the vacuum cleaner from the mains supply.
Press the handle release button and turn the vacuum
cleaner over so that the base lies flat and face up. Use a
screwdriver to remove the four retaining screws shown
above.Remove the nozzle guard.
Lift and remove the brush bar, then slide the belt off the
motor shaft and dispose of it. Place a new belt on the
motor shaft and then slip the brush bar through the belt.
The belt should sit on the end of the brush bar with no
bristles against the end cap. Re-fit the brush bar. Ensure
the end caps are in the correct position. Rotate the
brush bar to check the belt is not twisted. Replace the
nozzle guard (fig. 7/1).
.
Fig.5/1
nozzle guard
tabs
Fig.7/1
Fig.6/1
Fig.6/2
Fig.5/2
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 6
6
Troubleshooting
8. Troubleshooting
WWAARRNNIINNGG::
TO REDUCE RISK OF PERSONAL INJURY UNPLUG VACUUM CLEANER BEFORE SERVICING
PROBLEM: Cleaner won’t run
Cause: Not properly plugged into electrical outlet.
Solution: Plug cord in firmly.
Cause: Blown fuse or tripped beaker.
Solution: Check fuse or breaker. Replace fuse/breaker
PROBLEM: Cleaner won't pick up/loss of suction
Cause: Lower hose not connected properly.
Solution: Refer to page 3 for fitting information.
Cause: Dirt container not installed correctly or full.
Solution: See ‘Emptying the dirt container”.
Cause: Broken or worn belt.
Solution: Replace the belt.
Cause: Clogged filter.
Solution: Remove filter and clean.
Cause: Nozzle/hose or hose inlet is clogged.
Solution: Remove Nozzle/hose and obstruction.
PROBLEM: Dust escaping from the Vacuum
Cause: Dirt container full.
Solution: Empty dust canister.
Cause: Dirt container not installed properly.
Solution: See ‘Emptying the dirt container’.
Cause: Hose not installed properly.
Solution: See ‘putting your vacuum cleaner together’.
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 7
7
Uk Service & Help/Technical Specification
9. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone will be available out of these hours.
Any queries or concerns about using your Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the model number and serial
number of your Vax before calling. There are over 400
approved Vax Service Agents in the UK. For the
nearest Vax Service Agent, please call the Vax Careline
or visit www.vax.co.uk
10. Technical Specification
Voltage: 220 ~ 240V 50Hz
Wattage: 1450W Nom. 1650W Max
Capacity: 2.4 litres
Filters: Fibre pre-motor filter
Pleated paper post-motor filter
Cord length: 9.25m
Weight: 8.4kg
Subject to technical change without notice.
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 8
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility declare that the product
VS-19TLT Turboforce Lite is manufactured in compliance with the following:
Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC
EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
email: info@vax.co.uk - website: www
.vax.co.uk
Version 1
VS_19TL_Artwork.qxd 3/5/06 17:26 Page 1
Loading...