CORDLESS
Blade
CORDLESS SLIM VAC WITH
DETACHABLE HANDHELD
LET’S GET STARTED.
TBT3V1B1
TBT3V1P1
TBT3V1P2
TBT3V1B2
TBT3V1F1
TBT3V1H1
Let’s talk safety
This slim vac is intended for household use only and NOT for
commercial or industrial use.
Basic
• This slim vac does not stay upright without constant support.
Between uses, lie flat on the floor in a suitable location so that it
safety
does not become a trip hazard or can be stepped on.
precautions
• Only use the slim vac indoors on dry surfaces and keep the area
you’re cleaning well lit.
• Keep fingers, hair and loose clothing away from moving parts
and openings whilst using the slim vac.
• Don’t charge the slim vac outdoors, or leave the charger connected
to the mains when not in use.
Don’ts
• Don’t use the slim vac if it has been dropped, damaged, immersed
in water or left outdoors.
• Don’t handle the charger plug or use the slim vac with wet hands.
• Don’t run over the charger cord or use the slim vac if the
charger cord or plug is damaged. Please contact our
Customer Care Line on: 0330 026 8455.
• Don’t use the charger cord as a handle, pull the charger cord around
corners or sharp edges, or close a door over the charger cord.
• Don’t unplug the charger by pulling on the charger cord.
• Always turn off and unplug the slim vac from the charger before
carrying out any maintenance. Please refer to the appropriate
section in the user guide to review necessary precautions.
Do’s
• Always make sure the separator and filters are fitted correctly
before using your slim vac.
• Always switch off the slim vac before disconnecting or connecting
the reach wand and accessories.
• Keep all openings clear and free from debris as this may affect the
airflow/suction.
• Take extra care when using the slim vac on the stairs.
• This slim vac can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the slim vac in a safe way and understand the
hazards involved. Children should not play with the slim vac. Cleaning and
user maintenance should not be made by children without supervision.
• Only Vax recommended charger, tools and accessories should be
used with this slim vac.
• The battery must be removed from the appliance before it is scrapped.
• Don’t vacuum up hard or sharp objects such as glass, nails, screws, coins, etc.
• Don’t attempt to remove blockages with sharp objects as this may
cause damage to your slim vac.
• Don’t vacuum up hot coals, cigarette butts, matches or smoking hot
burning items or use in an area where there may be harmful fluids
(chlorine, bleach and ammonia drain cleaner).
• Don’t use the slim vac with incorrect voltage or charger as this may result in
damage or injury to the user. The correct voltage is listed on the ratings label.
• Don’t leave the slim vac in one spot for an extended period of time when
the brushbar is activated. This slim vac is fitted with a rotating brushbar
which, if left in one place, may cause damage to the floor surface.
• If charging the slim vac through an extension cord, use only CE approved
13amp extension cords, non-approved extension cords may overheat. Care
should be taken to arrange the extension cord as it can be a trip hazard.
• Always protect the power cable from heated surfaces and open flames.
• Store your slim vac in a cool, dry area. If filters have been cleaned as per
user guide instructions ensure they are thoroughly dry before storing away.
• Always use the charger supplied with the slim vac.
• The battery must be disposed of safely (for further information, read the
‘Getting started’ section).
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.
Thank you for buying this Vax Cordless Blade.
Taking care of your carpets and hard floors
The Vax Cordless Blade series is designed to make vacuuming carpets and
hard floors regularly, as effective and efficient as possible and this user
guide will help you get the most out of your machine.
Maintaining your carpets and hard floors will ensure they keep their
appearance for longer and Vax will help you take good care of them.
Taking care of your Vax Cordless Blade
Also inside this guide are instructions on maintaining your new machine, so
that it’s ready when you are to tackle your carpets and hard floors.
Taking care of you
We’re here if you need us. Instead of taking me
back to the shop, simply visit our online support
Still need to get in touch?
Our UK based Customer Care Team are here to support you - for help with assembly,
operational/performance problems or buying and fitting new accessories. Whether you wish to chat,
use Facebook, Twitter or call, you can find all our contact details.
This user guide can be found online
Let us know what you think
Contents
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
Accessories
What to do if it goes wrong
Getting in touch
Notes
Included with
your machine
Cordless Blade 32V
Cordless Blade 24V
Crevice Tool
Dusting Brush
Cordless Blade 32V Pro
Cordless Blade 32V Ultra
Cordless Blade 24V Pro
Cordless Blade 24V Ultra
Crevice Tool
Dusting Brush
Pet/Stair Tool
All models come with a charger, wall mount,
3 screws and user manual.
Getting to know your machine
Battery level indicator
Dirt container lid
Dirt container
Dirt release button
Charging port (hidden)
Handheld release button
Reach wand
Powered Head/
accessory release clip
Powered Head
Brushbar
On/Off button
Filter cover
Handle
Battery level gauge
Battery charging light
Boost mode on/off button
Brushbar on/off button
Wall bracket connection point
Technical Specification
Name Vax Cordless Blade 24V
Battery voltage See product
rating label Run time 35 minutes
Charge time 4 hours
Weight 3kg
Dust bin capacity 0.6L
Subject to technical change without notice.
Images are illustrative only.
Name Vax Cordless Blade 32V
Battery voltage See product
rating label Run time 45 minutes
Charge time 4 hours
Weight 3kg
Dust bin capacity 0.6L
Accessories & Consumables
Foam filter
1-7-138744
Pre-motor filter
1-7-138743
Pet/Stair tool
1-9-138760
Getting started
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Before you begin
CAUTION: Always switch off the slim vac before connecting or disconnecting the
handheld/attachments or removing and emptying the dirt container.
IMPORTANT: The slim vac is equipped with a thermal cut-out. If for any reason the slim vac does
overheat, the thermostat will automatically turn the slim vac off. If this happens empty the dirt container
and check the slim vac for blockages. Allow the slim vac to cool for approximately 1 hour (if you have
cleaned the filter, wait 24 hours for the filter to fully dry before putting back into the machine).
For best cleaning results, filters should be tapped over a bin every 4-6 uses to remove dirt and
debris, and washed every 3 months depending on the level of use.
Assembling your cordless slim vac
CAUTION: This slim vac is not free standing. Between uses or when carrying out any maintenance,
always lie flat on the floor in a suitable location so that it does not become a trip hazard or can be stepped on.
Line up the connector on
the reach wand with the
Powered Head. Push the
reach wand down onto
the Powered Head until it
clicks into place.
Push the handheld down
onto the reach wand
until it clicks into place.
The slim vac is not free standing and between uses
must always be placed in the wall bracket or laid flat
on the floor in a suitable location, so that it does not
become a trip hazard or can be stepped on.
Getting started
Fixing the wall bracket
Fully assemble
Line up the wall bracket with the back of the handheld.
the slim vac.
Slot the bracket into the handheld and push upwards
to lock into place.
Choose a location for the
slim vac to be stored,
preferably near to a
mains supply. Stand the
slim vac in the upright
position against the wall,
with the Powered Head
flat on the floor.
Using a pencil, make a
mark to show the
required position of the
wall bracket. Lift to
remove the slim vac
from the wall bracket.
Align the bracket back
to the wall and make
an additional 3 small
marks for each screw.
Use the screws and
wall plugs to secure the
wall bracket to the wall.
Store the slim vac on the
wall bracket by lifting the
slim vac slightly above
the bracket and sliding
the back of the handheld
down and onto the
bracket. Always ensure
the slim vac is securely
locked into place.
Getting started
PLEASE READ ‘LET’S TALK SAFETY’ BEFORE USE
CAUTION: The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not
disassemble or heat above manufacturer’s maximum temperature limit (60°C/140°F) or incinerate. Use of
another battery may present a risk of fire or explosion. Dispose of used battery promptly. Keep away from
children. Do not disassemble and do not dispose of in a fire. Do not attempt to disassemble the battery or
remove any component projecting from the battery terminals. The battery and charger have no user
serviceable parts. Fire or injury may result. Prior to disposal, protect exposed terminals with heavy insulating
tape to prevent shorting. The battery is to be disposed of safely at your local battery recycling centre.
Do not attempt to recharge non-rechargeable batteries. The battery must be removed from the
appliance before it is scrapped. The appliance must be disconnected from the charger/supply mains
before use and when removing or installing the battery into the machine. In case of battery leakages
avoid any contact with the skin.
Charging the cordless slim vac
NOTE: The initial charge is 4 hours and charging will be required before first use. The slim vac can be
charged as a handheld with the reach wand and tools removed or as an upright attached to the wall
bracket. Failure to fully charge the battery before first use (initial charge 4 hours) may result in poor
battery performance. The machine can remain on the battery charger once fully charged. The life
expectancy of the battery will vary depending on the usage of the slim vac.
WARNING: Do not use the slim vac when the machine is plugged in and charging.
To charge the machine
(as a handheld) detach
the reach wand and tools
and place the handheld
on a flat, stable surface.
You can also charge as
an upright slim vac when
attached to the wall
bracket.
Insert the charger lead Plug the charging plug
into the charging port into the mains.
located underneath the
nozzle on the handheld.
Getting started
Charging the battery
When the charger is connected, both the battery charging light on the back of the handheld and
battery indicator light on the handle will illuminate:
Red light - the slim vac is charging White light - the slim vac is charged
The battery level gauge lights will illuminate in turn as the battery charges, until all four lights are illuminated.
Once fully charged, the gauge lights will go out and the central light will illuminate white.
If charging for the first time the initial charge time is 4 hours.
When the slim vac is in use the battery level gauge
lights will illuminate indicating how much charge is
remaining. When only one light remains illuminated the
central charging light and battery level indicator will
turn red indicating the battery is running low (<25%).
Using your machine
NOTE: The slim vac has a constantly rotating brushbar when activated. Never leave the slim vac in one
spot for an extended period of time as this may damage the floor surface. Always turn the brushbar off
when cleaning hard floors. The brushbar should be ON for carpets and OFF for hard floors. To prevent
any damage being sustained test on an inconspicuous area of the flooring.
IMPORTANT: If the brushbar has been obstructed, the motor protection sensor may have been activated.
The brushbar will stop and the light on the Powered Head will illuminate red. To reset, remove the
Powered Head from the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting
the Powered Head, switch the slim vac on and press the brushbar on/off button.
Using the cordless slim vac
Place your foot on the Powered Head and
pull the handle backwards to recline.
To switch the brushbar on, press the brushbar on/off
button. The light on the Powered Head and the brushbar
on/off light will illuminate to indicate the brushbar is on and
the brushbar will constantly spin. To switch the brushbar
off press the brushbar button again.
The slim vac will always start with the brushbar off.
To switch the slim vac
on, press the on/off
button located on the
back of the handle. The
battery level indicator
light on the handle and
battery charging light
will illuminate white.
When the slim vac is
switched on, the boost
on/off button will also
illuminate, confirming that
the boost mode is ‘On’.
The slim vac will always
start in boost mode.
Pressing the boost button
will deactivate/activate the
boost mode.
Boost mode increases
suction for particularly
dirty areas that require
additional cleaning.
NOTE: Constant use of the boost mode and brushbar feature will reduce the battery run time.
Using your machine
Using the slim vac reach wand
The reach wand can be used for hard to reach places.
Press the Powered
Head/ accessory release
clip and pull to remove
the Powered Head from
the reach wand.
Choose an accessory
(pictures illustrated
depending on model).
Push the chosen
accessory into the
reach wand until it
clicks into place.
Boost mode increases
suction for particularly
dirty areas that require
additional cleaning.
To switch the slim vac
on, press the on/off
button located on the
back of the handle.
When the slim vac is switched on, the boost on/off
button will also illuminate, confirming that the boost
mode is ‘On’. The slim vac will always start in
boost mode. Pressing the boost button will
deactivate/activate the boost mode.
NOTE: Constant use of the boost mode will reduce the battery run time.
The reach wand can be used for hard to reach places
and at different heights for above floor cleaning.
The slim vac is not free standing and in between uses
must always be placed in the wall bracket, or laid flat
on the floor in a suitable location, so that it does not
become a trip hazard or can be stepped on.
Using your machine
Using the slim vac as a handheld
NOTE: The slim vac has a constantly rotating brushbar when activated. Never leave the slim vac in one spot for an
extended period of time as this may damage the floor surface. Always turn the brushbar off when cleaning hard floors.
The brushbar should be ON for carpets and OFF for hard floors. To prevent any damage being sustained test on an
inconspicuous area of the flooring. Always take extra care when using the slim vac on the stairs.
Press the handheld
release clip. Pull to
separate the handheld
from the reach wand.
The reach wand, when
attached to the Powered
Head/accessory, is not free
standing. Place safely and
securely to one side.
Choose an accessory
(pictures illustrated
depending on model).
Push the chosen
accessory into the
handheld until it is securely
locked into place.
Boost mode increases
suction for particularly
dirty areas that require
additional cleaning.
All of the accessories,
including the Powered
Head, can be attached
directly onto the handheld.
To switch the slim vac
on, press the on/off
button located on the
back of the handle. The
battery level indicator
light on the handle and
battery charging light
will illuminate white.
When the slim vac is switched on, the boost on/off
button will also illuminate, confirming that the boost
mode is ‘On’. The slim vac will always start in
boost mode. Pressing the boost button will
deactivate/activate the boost mode.
To switch the brushbar on, press the brushbar on/off
button. The light on the Powered Head and the brushbar
on/off light will illuminate to indicate the brushbar is on and
the brushbar will constantly spin. To switch the brushbar
off press the brushbar button again.
The slim vac will always start with the brushbar off.
Taking care of your machine
Emptying and cleaning the dirt container
CAUTION: Always switch off the slim vac and unplug from the charger and mains before
carrying out any maintenance or troubleshooting.
WARNING: Don’t over fill the dirt container to avoid blocking the air flow through the slim vac.
Press the handheld
release clip. Pull and
remove the reach wand
or the accessory that is
attached to the handheld.
The reach wand, when
attached to the Powered
Head/accessory, is not free
standing. Place safely and
securely to one side.
Hold the handheld over a bin and press the dirt
release button to allow dirt/debris to fall out.
Taking care of your machine
Cleaning the filters and separator
CAUTION: Always remove the reach wand/accessories from the handheld and empty the dirt container
before cleaning the filters and separator. DO NOT use the slim vac without both the filters in place.
For best cleaning results, the filters should be tapped over a bin every 4-6 uses to remove dirt and
debris and washed every 3 months depending on the level of use.
Cleaning the filters
Press the handheld
Twist the filter cover
Pull and remove the filter
release clip. Pull and
anticlockwise to unlock.
cover from the handheld.
remove the reach wand
or the accessory that is
attached to the handheld.
Pull the tab on the filter to remove from the cover.
24hr
On the handheld, pinch the
round foam filter inside the
separator and pull to remove.
Tap both filters over a bin to
remove any dirt/debris.
Wash the filters under Leave for 24hrs or until
running water (40°C max). fully dry before replacing.
Taking care of your machine
Cleaning the separator
Press the handheld
release clip. Pull and
remove the reach wand
or the accessory that is
attached to the handheld.
Hold the handheld over a bin and press the dirt
release button to allow dirt/debris to fall out.
Twist the filter cover Pull and remove the filter
anticlockwise to unlock. cover from the handheld.
Press the dirt release
button to open the dirt
container.
To release the separator,
push from inside the dirt
container and pull out the
separator to remove.
Pinch the round foam
filter inside the top of
the separator and pull
to remove. Tap both
parts over a bin to
remove dirt/debris.
Wash the foam filter and
the separator under running
water (40°C max).
24hr
Leave for 24hrs or until
fully dry before refitting
the filter back into the
slim vac.
Let’s talk technical
Removing blockages from the handheld and reach wand
Press the handheld
release button and
remove the reach
wand. Check and clear
any dirt and debris from
this connection point.
To test for a blockage in the reach wand, drop a small
ball of paper into the wand. The paper will drop
through if the wand is clear. Use a broom handle or
similar blunt object to remove any blockage.
Removing blockages from the Powered Head
IMPORTANT: If the brushbar has been obstructed, the motor protection sensor may have been activated.
The brushbar will stop and the light on the Powered Head will illuminate red. To reset, remove the
Powered Head from the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting
the Powered Head, switch the slim vac on and press the brushbar on/off button.
Press the Powered
Head/ accessory release
clip and pull to remove
the Powered Head from
the reach wand.
Check the Powered
Head for any blockages
and use a blunt object to
remove the blockage.
Using scissors, remove
any threads or hair from
around the brushbar and
clear any dirt or debris
from the Powered Head.
Let’s talk technical
Removing and replacing the brushbar
A
On the base of the
floorhead, find letter A
to indicate the side of
the brushbar cover that
needs to be removed.
Using a cross head
Slide the brushbar out
Clear any threads or
screwdriver, unscrew the
from the brushbar housing.
hair from around the
three screws and remove
brushbar and any dirt/
the brushbar cover.
debris inside the housing
of the Powered Head.
To re-fit the brushbar, firstly push the brushbar onto
the brushbar cover, then slide the brushbar and cover
back into the brushbar housing. Make sure the end of
the brushbar sits securely in place. Refit and tighten
the screws to secure.
Removing and replacing the belt
B
On the base of the
floorhead, find letter
B to indicate the side
of the belt cap that
needs to be removed.
Using a cross head
screwdriver, unscrew
the three screws and
remove the cover.
If the belt is broken,
remove this and slide the
new belt onto the cogs.
Refit the belt cover
and tighten the
screws to secure.
Accessories
Also available Vax Cordless Blade Tools
Refer to ‘Using your machine’ section for tool assembly instructions.
Vax Cordless Blade tools
Crevice Tool
1-9-138758
The crevice tool is ideal for use all around the home.
It’s perfect for those tricky corners and crevices.
Dusting Brush
1-9-138759
The dusting brush is ideal for dusting furniture
and hard surfaces such as sofas and shelving.
Pet/Stair Tool
1-9-138760
An ideal tool to help tackle those pet hairs! Simply clip this
tool onto the handheld and begin cleaning. The rubber
teeth are designed to agitate fine hair on both carpets and
hardfloor. This tool is also great for stair cleaning!
What to do if it goes wrong
Problem Solution
There is an
accessory missing
• Check the contents panel on the box to make sure the part is
included with your slim vac.
Why does my slim
vac have no power?
• The battery may not be charged. Go to ‘Getting Started’.
• The motor thermostat may have tripped. If this has happened, switch off the slim vac.
Empty the dirt container and check for blockages. Clean the filters and allow the slim
vac to cool for approximately 1 hour (if you have washed the filters you will need to
wait 24 hours for the filters to fully dry before putting them back into the slim vac).
Why isn’t my slim
vac charging?
• Check the battery charger is plugged in. Go to ‘Getting started’.
• The slim vac may be warm from use. Allow the slim vac to fully cool before retrying.
Why won’t the slim
vac pick up?
• The filters or separator are not correctly fitted. Go to ‘Taking care of your machine’.
• The filters may be clogged, clean the filters. Go to ‘Taking care of your machine’.
• The dirt container may be blocked, empty the dirt container. Go to ‘Taking
care of your machine’.
• The brushbar on the Powered Head has not been activated. Go to ‘Using your machine’.
• There maybe a blockage in the reach wand. Disconnect from the slim vac and
carefully remove any blockages. Go to ‘Let’s talk technical’.
• Low suction has been selected. Activate the boost mode to increase
suction. Go to ‘Using your machine’.
• The Powered Head may be blocked. Go to ‘Taking care of your machine’.
Why is the red light on?
• Battery charge is running low (<25%). Go to ‘Getting started’.
• If the brushbar has been obstructed the motor protection sensor may have been
activated. The brushbar will stop and the light on the Powered Head will illuminate red.
To reset, remove the Powered Head from the reach wand/handheld and clear any
obstruction. Wait 1 minute before refitting the Powered Head, switch the slim vac on
and press the brushbar on/off button. Go to ‘Lets talk Technical’.
Why won’t the Powered
Head brushbar turn?
• The Powered Head brushbar has not been activated. Go to ‘Using your machine’.
• If the brushbar has been obstructed the motor protection sensor may have been
activated. The brushbar will stop and the light on the Powered Head will illuminate red.
To reset, remove the Powered Head from the reach wand/handheld and clear any
obstruction. Wait 1 minute before refitting the Powered Head, switch the slim vac on
and press the brushbar on/off button. Go to ‘Lets talk Technical’.
• The slim vac, floorhead and reach wand may not be correctly fitted.
Reassemble and retry. Go to ‘Getting started’.
• The Powered Head may be obstructed. Go to ‘Let’s talk technical’.
Why is dust escaping
from the slim vac?
• The filters may be clogged, clean the filters. Go to ‘Taking care of your machine’.
Notes
Notes
EU Statement of Compliance: Manufacturer/EU importer: Vax Limited, hereby on our own responsibility, declare that the
TBT3V1B1/ TBT3V1P1/TBT3V1P2/TBT3V1B2/TBT3V1F1/TBT3V1H1 are manufactured in compliance with the following
Directives: Safety: 2014/35/EU Low Voltage Directive. EMC: 2014/30/EU Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice.
© 2016 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge are the property of Techtronic
Floor Care Technology Ltd and are registered in the EU and may be pending or registered in other countries.
This marking on the product(s) and/or accompanying documents means that used electrical and electronic equipment (WEEE)
should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to
designated collection points where it will be accepted free of charge. Disposing of this product correctly will help save valuable
resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from
inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point.
Loading...