Steam Fresh
Let’s get started
S86-SF-A
vax.co.uk
Let’s talk safety
Basic
safety
precautions
Don’ts
This steam mop is intended for household use only and
NOT for commercial or industrial use.
WARNING: Danger of scalding
• Only use the steam mop indoors and keep the area you’re
cleaning well lit.
• Keep ngers, hair and loose clothing from moving parts
and openings whilst using the steam mop.
• This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
• Don’t touch any hot areas/accessories on your steam mop.
• It’s normal for the steam mop and accessories to heat up during
use, always allow them to cool down before handling.
• Don’t use the steam mop if it has been dropped, if there are visible
signs of damage or if it is leaking, if it has been immersed in water
or left outdoors.
• Don’t handle the plug or use the steam mop with wet hands.
• Don’t pull or carry this steam mop by the power cord.
• Don’t use the power cord as a handle, pull the power cord around
corners or sharp edges or close a door over the power cord.
• Don’t attempt to remove blockages with sharp objects as this may
Do’s
• Always ll the clean water tank with water only, never
add perfume, stain remover or products containing alcohol.
Filling the clean water tank with hot or boiling water will
damage the machine and invalidate your guarantee.
• Always make sure tanks are tted correctly before using
the steam mop.
• Always vacuum your carpets thoroughly and ensure hard oor
areas are free from grit and debris before using the steam mop.
• Always carry the steam mop by the handle.
• Always unplug the steam mop before carrying out any
maintenance or when unattended.
• Turn o all controls on the steam mop before disconnecting
or connecting the power cord, after use always wrap the power
cord around the cord clips provided.
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
• Please refer to oor manufacture’s care recommendations before use, and test
your ooring/carpet/rugs by running the steam mop over a small hidden area,
if no pile distortion or no damage occurs continue cleaning. Not suitable for use
on wax polished oors or furniture, acrylic surfaces and synthetic, velvet
or steam/water sensitive materials.
• This steam mop should not be used to clean electrical appliances such
as microwaves, oven, televisions and electrical heating systems etc.
• Only Vax recommended cloths and detergent should be used with this
steam mop. Using other detergents will invalidate the guarantee.
cause damage to the steam mop, remove blockages only as instructed
in this guide.
• Don’t unplug steam mop by pulling on the power cord or run over the power cord.
If the power cord or plug is damaged please contact out Customer Care Line
on 0330 026 8455 (Mon-Fri 8:30am to 6:30pm, Sat 9:00am to 5:00pm).
• Don’t aim the steam mop at people, animals, plants and electrical components
such as interior of ovens or wires. Never touch the oorhead from a short
distance (there is a risk of scalding).
• Don’t use the steam mop with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
• Don’t leave this steam mop unattended while it is connected to the supply mains.
• Take extra care when cleaning on stairs.
• Always replace the fuse in the plug with a British 13amp fuse.
• Always protect the power cable from heated surfaces or near open ames.
• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat.
• Care should be taken to arrange the extension cord as it could be a trip hazard.
• Store the steam mop in a cool, dry area away from children.
• Before storing the steam mop please ensure all water/detergents tanks
and hard water lter are thoroughly clean and dry.
• Keep the appliance out of reach of children when it is energised
or cooling down.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE.
Thank you for buying this Steam Fresh
Taking care of your sealed hard oors and surfaces
The Steam Fresh is designed to make the regular cleaning of your sealed hard oors
as eective and ecient as possible. This user guide will help you get the most out
of your machine.
Maintaining your sealed hard oors with the Steam Fresh will ensure they keep looking beautiful,
smell fresh and are hygienically clean.
Taking care of your Steam Fresh
Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your sealed hard oors.
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd, Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich, WR9 OLW, UK
This User Guide can be found online at: vax.co.uk/support
Let us know what you think @VaxUK
Contents
Steam Fresh
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Notes
Accessories
What to do if it goes wrong
Included with
your machine
250ml detergent
1x Microbre
cleaning pad
Carpet glider
Getting in touch
Getting to know your machine
Handle
Detergent trigger (hidden)
Twin tank release button
Twin tank
Hard water lter (hidden)
Detergent dial
On/O switch
Floorhead
Technical Specication
Name Stream Fresh
Voltage 220-240
Wattage 1600w
Cord length 6.5m
Weight 6.5kg
Handle release button
Quick cord
release hook
Plug storage
Quick cord
release hook
Floorhead
release button
Carpet glider
Accessories & Consumables*
Microbre Cleaning Pads (Type 1)
1-1-131448-00
Carpet Glider (Type 3)
1-1-133527-00
Hard Water Filter (Type 1)
1-1-133327-00
Subject to technical change without notice.
*To purchase consumables and accessories, please visit vax.co.uk
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Assembling your steam mop
Getting started
Push the main body down
into the oorhead until
it clicks into place.
Stand the steam mop
upright by pushing the
main body forward
to lock into position.
Assembling your steam mop
Place the cleaning pad on the oor
white side facing up. Place steam
mop onto pad making sure the
entire pad covers the oorhead.
Filling twin tank
WaterDetergent
Push the handle
into main body until
it clicks into place.
Filling twin tank
Press the twin tank release button
and lift the twin tank by the handle.
Wrap power cord around hooks
for easy storage and insert into
plug storage.
Twist water cap anti-clockwise
and lift to remove.
Fill the water tank with 500ml
of water, replace cap, to tighten
twist clockwise.
Using your machine Using your machine
IMPORTANT: If you do not want to use detergent on your ooring, select o on the detergent dial.
Always test on an inconspicuous area of ooring rst before using detergent.
Filling twin tank
Twist the detergent cap
anti-clockwise and lift
to remove.
Pour 50ml of Vax
detergent and 250ml of
water into the detergent
tank then replace cap and
twist clockwise to tighten.
Before replacing the twin
tank make sure the hard
water lter is in place.
Align the twin tank
and push until it clicks
into place.
Before you begin cleaning
• IMPORTANT: Please refer to oor manufacturer’s care recommendations before use and test the steam mop
on a discrete area of ooring to begin with.
• The steam mop and accessories get very hot during use, always allow them to cool down before handling.
• Always unplug and switch o the steam mop when assembling.
• Always switch o the steam mop before emptying the water tank or changing the cleaning pads/accessories.
• When using the steam mop, basic safety precautions should always be observed.
• Don’t aim the steam mop at people, animals, plants and electrical components such as interior of ovens or wires. Never touch
the steam burst or oorhead from a short distance. (There is a risk of scalding)
• The steam mop is equipped with a thermostat and a thermal cut-out. If for any reason the steam mop overheats
it will switch o. If this happens turn o and unplug the steam mop, allow to cool for a least 2 to 4 hours and re-start.
Using your machine
Place the microbre pad
on the oor white side
facing up. Place the
oorhead onto the
microbre pad making
sure it covers the
entire oorhead.
Plug into mains and slide
switch to on position.
The blue light will
illuminate to show
power on. The green light
will illuminate to show
the steam mop is ready
to use.
To steam your oors
without detergent select
o. This is generally
recommended for carpet
and wood ooring.
To use with detergent
select min to max as
desired. This is generally
recommended for tile
and vinyl ooring.
Using your machine
Place your foot onto the
oorhead and pull handle
backwards to recline.
Refreshing carpets
Place the microbre pad
on the oor white side
facing up. Place steam
mop onto pad making
sure the entire pad
covers the oorhead.
Refreshing carpets
To produce steam,
squeeze the trigger.
To prevent over wetting
oors avoid holding the
trigger continuously.
With microbre pad attached, hook
steam mop into the font of the
carpet glider and push to clip into
place. Carpet glider should only be
used when refreshing carpets.
Move the steam mop slowly
backwards and forwards paying
particular attention to high
trac areas.
Plug into mains and slide
switch to on position.
The blue light will
illuminate to show power
on. The green light will
illuminate to show the
steam mop is ready to use.
illuminate to show the
steam mop is ready to use
To refresh carpets select o
setting on the detergent dial.
.
Using your machine Taking care of your machine
Refreshing carpets
Place your foot onto the
oorhead and pull handle
backwards to recline.
To produce steam,
squeeze the trigger.
To prevent over wetting
oors avoid holding the
trigger continuously.
Refreshing carpets
To release the carpet glider,
place your foot on clip and
push down. Lift steam mop
to remove.
CAUTION: Always turn OFF the steam mop
when tting the cleaning pads.
IMPORTANT: Never use the steam mop without
a cleaning pad attached to the oorhead. Never leave
the steam mop in one spot for extended period
of time or with a damp or wet pad attached
as this may damage the oors surface.
Move the steam mop slowly
backwards and forwards across
the carpet paying particular
attention to high trac areas.
CAUTION
When using on carpets, always
make sure the microbre cleaning
pad is used and covers the oorhead
entirely before using the carpet
glider. Only use the carpet glider
when refreshing carpets.
Taking care of your machine
IMPORTANT: Allow the steam mop to fully cool down before performing any maintenance or troubleshooting checks
Don’t leave water or detergent in the twin tank between uses, as this can eect the machines performance, the twin tank
needs to be emptied and rinsed after each use.
Emptying the twin tank
Press the twin tank
release button and lift the
twin tank by the handle.
IMPORTANT: Don’t use bleach or fabric softener when washing the microbre cleaning pad.
Always allow the steam mop to fully cool down before removing the microbre cleaning pad.
Cleaning the microbre cleaning pad
Twist water cap
anti-clockwise and lift
to remove.
Empty any excess water over
the sink, replace water cap
and turn clockwise to tighten.
Storing your steam mop
Max 40°C
Hold corner of pad down
with foot and lift steam mop
to peel away.
IMPORTANT: Don’t operate the steam mop without hard water lter in place. The condition of the lter aects the
performance of your machine, check and change lter periodically. If you live in an area of hard water the lter will
discolour or darken over time. Depending on water hardness and frequency of use, the lter should be changed every
3 to 6 months or if the lter has discoloured.
The microbre pad is machine
washable (Max 40°C) allow to
fully dry before use.
Wrap the power cord around the quick
cord release hooks and insert the plug
into the plug storage socket.
Replacing the hard water lter
Remove twin water
tank to access the
hard water lter.
Lift to remove the hard
water lter.
Clearing blockages
If there is an obstruction to the
steam ow through the machine,
steam may be released through
the bleed valve.
Clearing blockages
New lter -
(beige/cream colour).
To remove the oorhead from
main body push the plastic clip
and lift.
Hard water lter should be
replaced every 3-6 months
or when discoloured and
darkened (dark orange).
After oorhead
is removed, using a thin
object such as a paper-clip
(in the area shown), insert
to remove the blockage.
Remove cleaning pad and
inspect steam mop base for
blockages. If a blockage can
be seen use a small thin object
such as a paper-clip
insert to remove.
NotesTaking care of your machine
NotesNotes
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
2x Mircrobre Cleaning Pads (Type 1)
1-1-131448-00
Microbre cleaning pads, ideal to remove dirt and
grime. These cleaning pads attach to the base of the
steam mop using velcro, so it’s quick and easy to t
and remove.
2x Microbre Pet Pads (Type 9)
1-1-133265-00
Microbre pet pads. Super absorbent, touch stain
removal and ideal for picking up pet hairs.
These cleaning pads attach to the base of the
steam mop, so it’s quick and easy to t and remove.
Pro Cleaning Pads (Type 6)
1-1-132319-00
3x pro cleaning pads. Ideal for stubborn stain
removal throughout your home. These cleaning
pads attach to the base of the steam mop, so it’s
quick and easy to t and remove.
Steam Mop Cleaning Pads
(1-1-131864-00)
2x microbre cleaning pads, Ideal to remove dirt and grime.
2x coral cleaning pads for your Steam mop cleaner.
Super absorbent and are ideal for removing stubborn stains.
Total Home
1-1-132528-00
8x microbre cleaning pads. Avoid cross
contamination between dierent areas
of your home with this Total Home Cleaning Kit.
Kit contains 8 x coloured microbre cleaning pads
for all areas of your home. Kit also contains a free
wash bag worth £9.99.
Hard Water Filter (Type 1)
1-1-133327-00
3x hard water lters to prevent the build-up of lime
scale deposits in hard water areas.
Steam Detergent Pet
1-9-132813-00
Vax Pet Steam Detergent cuts through grease and
grime, neutralises pet odours, and leaves your
oors smelling of Apple Blossom.
Steam Detergent Spring Fresh
1-9-132807-00
Vax Spring Fresh Steam Detergent cuts through
grease and grime, neutralises odours and
leaves your oors smelling Spring Fresh.
AccessoriesAccessories
Steam Detergent Lime Zest
1-9-132809-00
Vax Lime Zest Steam Detergent cuts through
grease and grime, neutralises odours, and leaves
your oors smelling of Lime Zest.
Steam Detergent Ocean Breeze
1-9-132811-00
Vax Ocean Breeze Steam Detergent cuts through
grease and grime, neutralises odours, and leaves
your oors smelling of Ocean Breeze.
What to do if it goes wrong
SolutionProblem
• Check the ‘This pack contains’ panel on the box to make sure
the part is included with your steam mop.
There is an
accessory missing
• Check the On/O switch is in the On position.
• The plug may not be fully pushed into the electrical socket.
The steam mop
won’t turn on?
Why is the steam mop
not producing
steam/detergent?
• Check the fuse in the plug if this needs replacing, always replace
with a British 13amp fuse.
• There may be no water in water tank, check the water tank has water.
• Check the water tank is securely tted and the hard water lter is in place.
• Hard water lter may be blocked or discoloured and needs to be replaced.
• The water may not yet be at temperature, the green indicator light will
be illuminated when its ready.
• Steam path may be blocked. Go to ‘Let’s talk technical’ page.
• Putting detergent into the water tank can cause damage to the steam mop.
• Check correct setting has been selected, to use detergent
selected vinyl or tile.
• Check the detergent has been diluted to correct strength.
• The cleaning pad may already be saturated or dirty, wash the cleaning
pad. Go to the ‘Taking care of your machine’ pages.
Why won’t the cleaning
pad pick up dirt?
• Steam coming from the side of the machine indicates a blockage within
the machine. To clear any blockages go to the ‘Taking care
Why is steam coming
of your machine’ pages.
from the side of
the steam mop?
Caution: Always unplug the steam mop before performing maintenance/troubleshooting checks
Getting in touch
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
†
Registration required. Terms and conditions apply, see vax.co.uk for details.
@VaxUK
Vax Ltd., 5th Floor 2 Colmore Square, 38 Colmore Circus, Queensway, Birmingham, B4 6BN, UK
email: info@vax.co.uk website: vax.co.uk
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility,
declare that the S86-SF-A is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Loading...