Vax Rapid Power ECGLV1B1 Carpet Cleaner User guide

SERIES

CARPETS DRY IN AS LITTLE AS 1 HOUR*

LET’S GET STARTED.

ECGLV1B1
CWGRV011
CWGRV021
CDCW-RPXR

*Tested in quick clean mode. Results may vary.

Let’s talk safety

Basic safety precautions

This carpet washer is intended for household use only and NOT for
commercial or industrial use.

• Only use the carpet washer indoors and keep the area you’re cleaning well lit.

• Keep fingers, hair and loose clothing away from moving parts and openings
whilst using the carpet washer.

• This carpet washer can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the carpet washer in a safe way and understand the hazards
involved. Children should not play with the carpet washer. Cleaning and user
maintenance should not be made by children without supervision.

• Before using the carpet washer test your carpets/rugs/upholstery for
colourfastness and pile distortion.

• Only VAX recommended solution should be used with this carpet washer.
Using other solutions may invalidate the guarantee.

Don'ts

• Don’t leave the carpet washer plugged in when unattended.

• Don’t use the carpet washer if it has been dropped, damaged, immersed in
water or left outdoors.

• Don’t run over the power cord or use the carpet washer if the power cord
or plug is damaged. If the power cord is damaged, it must be replaced by a
qualified person in order to avoid a hazard.

• Don’t use the carpet washer to pick up any flammable or combustible materials
(lighter fluid, petrol, kerosene etc.) or use the carpet washer in an area with
explosive vapours or liquids.

• Don’t handle the plug or use the carpet washer with wet hands.

• Don’t use the carpet washer to pick up hot coals, cigarette butts, matches or
smoking hot burning items or use in an area that is wet or where there may be
harmful fluids (chlorine, bleach and ammonia drain cleaner).

• Don’t leave the carpet washer in one spot for an extended period of time when
it is switched on. This carpet washer is fitted with a rotating brushbar which, if
left in one place, may cause damage to the floor surface.

• Don’t pull or carry the carpet washer by the power cord. Don’t use the power
cord as a handle, pull the power cord around corners or sharp edges, or close
a door over the power cord. Don’t unplug the carpet washer by pulling on the
cord.

• Don’t carry the carpet washer whilst it's switched on.

2

• Don’t attempt to remove blockages with sharp objects as this may cause
damage to your carpet washer.

• Don’t use the carpet washer with incorrect voltage as this may result in
damage or injury to the user. The correct voltage is listed on the ratings label.

Do's

• Always vacuum your carpets thoroughly before using the carpet washer.

• Check with the manufacturer of your flooring prior to using the carpet washer.
Test all carpets and rugs for colourfastness and pile distortion before full usage.
Run the carpet washer over a small hidden area. If no damage or pile distortion
occurs continue cleaning.

• The clean water tank should be filled with warm water (max 40°C) only.
Filling the clean water tank with hot or boiling water will damage the machine
and invalidate the guarantee.

• Always turn off and unplug the carpet washer from the mains before
carrying out any maintenance and before connecting or disconnecting the
hose/accessories.

• Turn off all controls on the carpet washer before disconnecting or connecting
the power cord. After use always wrap the power cord around the cord clips
provided.

• Always keep the power cord away from the brushes whilst using the carpet
washer.

• Always replace the fuse in the plug with a British 13amp fuse. Always protect
the power cable from heated surfaces and open flames.

• Take extra care when cleaning on the stairs.

• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat. Care should be taken to arrange the extension cord as it can be
a trip hazard.

• Always use the carpet washer with all water/solution tanks and filters in place.

• Always check accessories are free from damage, dirt and debris before use.

• Keep all openings clear and free from debris as this may affect the airflow/
suction.

• Always use the carpet washer in an upright position. To prevent motor damage
from dirty water, never hold the carpet washer upside down or on its side.

• Store the carpet washer in a cool, dry area. Before storing the carpet washer
ensure all water/solutions tanks and filters are thoroughly clean and dry.

PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE.

3

Thank you for buying the

Taking care of your carpets

The Rapid Power is designed to make washing carpets regularly, as effective and efficient as
possible and this user guide will help you get the most out of your machine.

Maintaining your carpets will ensure they keep their appearance for longer and smell fresh and
clean. You’ve chosen carpets for your home for a reason and VAX will help you take good care
of them.

Taking care of your Rapid Power

Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets.

We’re here if you need us

Instead of taking your machine back to the shop,
simply visit our online support:

support.vax.co.uk

Still need to get in touch?

Our UK based Customer Care Team are here to support you.
For help with assembly, operational or performance problems, or buying and fitting new accessories,
you can find all our contact details at vax.co.uk/contact

This user guide can be found online at: support.vax.co.uk

4

Contents

Standard tools included
with your machine

Let's talk safety

Getting to know your machine

Getting started

Using your machine

Taking care of your machine

Let's talk technical

What to do if it goes wrong

Getting in touch

2 - 3

8 - 11

12 - 13

14 - 15

16

17

6

2.5m
Hose

250ml

Platinum

Solution

Accessory

Bag

7

Rapid Power

All standard tools, plus

2 in 1 Antimicrobial Tool

Rapid Power Refresh

All standard tools, plus

Wash Tool

Rapid Power Revive

All standard tools, plus

Accessories

Notes

18

19

Wash Tool Crevice Tool

Rapid Power Plus

All standard tools, plus

2 in 1 Antimicrobial Tool

Spin Scrub
Tool

250ml Pre
Treatment
Solution

Crevice Tool

250ml Post
Treatment
Solution

5

Getting to know your machine

Handle

Clean water/solution
tank release button

Clean water tank cap

Wash/Rinse dial

Dirty water tank
release latch

Dirty water tank

Dirty water tank
release latch

Solution tube
connection port

Trigger (hidden)

Solution tank cap

Clean water

/solution tank

Hose

connector

port

Cleaning
mode dial

Quick cord
release hook

Recline

pedal

On/Off

pedal

Nozzle

SpinScrub brushes

Technical Specification

Name Rapid Power
Code ECGLV1B1
Part number 1-1-138933
Voltage 220-240V ~ 50/60Hz
Wattage 1200W
Cord length 8m
Weight 8.4kg

Subject to technical change without notice. To purchase consumables and accessories, please visit vax.co.uk

6

Name Rapid Power Refresh
Code CDCW-RPXR
Part number 1-1-142258
Voltage 220-240V ~ 50/60Hz
Wattage 1200W
Cord length 8m
Weight 8.4kg

Name Rapid Power Revive
Code CWGRV011
Part number 1-1-141030
Voltage 220-240V ~ 50/60Hz
Wattage 1200W
Cord length 8m
Weight 8.4kg

Name Rapid Power Plus
Code CWGRV021
Part number 1-1-141031
Voltage 220-240V ~ 50/60Hz
Wattage 1200W
Cord length 8m
Weight 11.05kg

Getting started

PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE

IMPORTANT: Carpets should be dry vacuumed thoroughly before washing.

Test for colourfastness – Wet a white absorbent cloth with the solution. In a small hidden area of your carpet/rugs/
upholstery gently rub with the dampened cloth. Wait ten minutes and check for colour removal or bleed with a white paper
towel or cloth. If your carpet has more than one colour, check all colours.

Test your carpet/rugs/upholstery – Run the carpet washer over a small hidden area. If no pile distortion occurs continue
cleaning.

When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture cannot be moved, place
aluminium foil or wax paper under the legs. This will prevent wood finishes from staining your carpet. Pin up furniture skirts
and curtains.

When using the carpet washer, basic safety precautions should always be observed and don’t over saturate your carpets.
Only use VAX carpet solution. Using other solutions may cause excess foaming and will invalidate your guarantee. The clean
water tank should only be filled with warm water (max 40°C). Filling the clean water tank with hot/boiling water will damage
your machine and invalidate the guarantee. This is a powerful carpet washer, before plugging in make sure all controls are
turned off. Hold carpet washer firmly when starting and during use.

Assembling your carpet washer

Line up the handle and
slide onto the main body.

Insert the 2 screws and
tighten using a cross head
screwdriver.

Tilt the clean water/
solution tank and line up
onto carpet washer. Push
tank back until it clicks
into place.

Wrap the power cord
around the cord hooks
for storage.

7

Using your machine

CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

IMPORTANT: Your dirty water tank is tted with a oat. When the dirty water tank is full, or the oorhead is not in contact

with the carpet, the oat will shut o the suction on the carpet washer. You will be able to hear if this has happened as the
motor noise on the machine will increase. Once the oat is activated, empty the dirty water tank if full. If the dirty water tank
is not full then turn o your machine at the power switch and wait for the oat to settle.

Using the carpet washer and cleaning modes

NOTE: Carpets should be dry vacuumed thoroughly before washing. For best overall results use in deep clean mode.
For heavily soiled areas it may be necessary to repeat the cleaning process. Make crisscrossing strokes to the original
pattern and overlap each pass.

Quick Clean Mode: Best for a quick, surface clean because carpets dry in as little as 1 hour.

Deep Clean Mode: Best overall results for a thorough, deep clean.

Press the clean water/
solution tank release
button, pull and lift to
remove the tank.

Fill the clean water tank
with warm water (max
40°C). Replace the cap
before retting the tank.

Twist the solution tank
cap anti-clockwise to
remove.

Tilt the clean water/
solution tank and line up
onto the carpet washer.
Push the tank back until
it clicks into place.

Always empty and rinse out the clean and
dirty water tanks and leave to air dry before
replacing. Do not leave solution stored in
the tanks between uses.

8

Pour VAX carpet cleaning
solution into the tank.
Replace the cap.

Choose the cleaning mode
by turning the dial on the
base.
Quick Clean Mode: Best
for a quick, surface clean
with carpets drying in as
little as 1 hour.
Deep Clean Mode: Best
overall results for a
thorough, deep clean.

TIP

Twist the water tank cap
anti-clockwise to remove.

Turn the wash/rinse dial
to ‘wash’. The SpinScrub
brushes deep clean your
carpets with water and
detergent removing dirt
and stains.

Using your machine

Plug into the mains,
press the on/o pedal
to switch on.

Using Rinse mode

Turn the wash/rinse
dial to rinse. Only water
is released to remove
solution residue.

Press the recline pedal
and pull the handle
backwards.

For best results apply
water on the forward
stroke and release the
trigger to pick up water
on the backward stroke.
Follow with a slow
additional dry stroke
without the trigger
pressed for a dryer nish.

Squeeze the trigger to
release solution and
water mix.

For best results apply
water/solution on the
forward stroke and
release the trigger to pick
up water/solution on the
backward stroke. Follow
with a slow additional dry
stroke without the trigger
pressed for a dryer nish.

For best cleaning results use slow straight
parallel strokes. Intermittent dry forward
strokes will increase water pick up.

TIP

9

Using your machine

CAUTION: Test for colourfastness – Wet a white absorbent cloth with the solution. In a small hidden area of your carpet/
rugs/upholstery gently rub with the dampened cloth. Wait ten minutes and check for colour removal or bleed with a white
paper towel or cloth. If your carpet has more than one colour, check all colours.

IMPORTANT: The carpet washer should be in the upright position when using the hose and tools; de-activating the
SpinScrub brushes and brushbar. Do not place the washer at top of stairs to avoid it falling down stairs. Place washer at
bottom of stairs and work up.

Using the hose and wash tool

Pour VAX carpet cleaning
solution into the solution
side of the tank.

Line up the arrow on the
hose with the arrow on
the washer and push the
hose into position. Rotate
the hose clockwise to lock
into place.

Slide the tool over the tab
at the end of the hose
until it clicks into place.

10

Fill the clean water
tank with warm water
(max 40°C).

Pull to open the solution tube connector cover and push
the solution tube rmly onto the port.

Plug into the mains and
press the on/o pedal to
switch on.

Turn wash/rinse dial
to wash.

Open the hose connector
cover.

Attach the tool.

Use the carpet washer
or hose to pick up
spills before washing
and cleaning
the area.

TIP

Using your machine

Press the trigger on the
hose to release solution
/water.

Squeeze the trigger
on the forward stroke,
release the trigger on the
backward stroke to pick
up solution/water. Follow
with a slow additional dry
stroke without the trigger
pressed for a dryer nish.

Using rinse mode on the hose

Turn the wash/rinse
dial to rinse. Only water
is released to remove
solution residue.

Press the trigger on the
hose to release water.

To remove the tool, lift and
push the tool clip over the
tab at the end of the hose
and pull to remove.

Squeeze the trigger
on the forward stroke,
release the trigger on
backward stroke to pick
up water. Follow with
an additional dry stroke
without the trigger
pressed for a dryer nish.

11

Taking care of your machine

CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

Emptying and cleaning the dirty water tank

IMPORTANT: Always empty and rinse out clean and dirty water tanks and leave to air dry before replacing. Do not leave
solution stored in the tanks between uses.

Lift the tank release clip
and unhook from the front
of the dirty water tank.

Empty the dirty water
over the sink. Rinse the
dirty water tank and lid
under water (40°C max)
to remove dirt/debris.

Use the handle to lift
and remove the dirty
water tank.

Remove the lter from under the dirty water tank lid.
Wash under water (40°C max) to remove dirt and debris
and allow to dry for 24 hours before retting.

For emptying mid clean,
pull the quick pour spout
cap to open. Pour the dirty
water into the sink. Always
make sure the spout is fully
closed before retting to
the washer.

Not correctly retting the
quick pour spout or dirty
water tank lid will result in
poor dirty water pick up.

For emptying at the end
of a clean, lift and unhook
the latch on the tank and
lift to remove the lid.

To replace the lid, slide
the tabs on the back of
the lid into the tabs on the
tank and close in a hinge
line manner.

IMPORTANT

12

Taking care of your machine

Lift and hook the latch
on the tank onto the lid
and push down to lock
into place.

To re-t, slide the dirty
water tank onto the carpet
washer, making sure
the tabs on the tank line
up with the back of the
washer.

Removing and cleaning the nozzle

Remove both tanks and tilt
the carpet washer so it is
lying on its back.

Lift the nozzle release clip
to unlock the nozzle.

Hook the tank release
catch over the front of the
tank and push downwards
to lock the catch in place.

Hold the front of the
nozzle and push down to
release the nozzle away
from the washer. Once
released, lift to remove.

Rinse nozzle under water
(40°C max) to remove dirt
and debris.

To replace the nozzle, hook the tabs on nozzle with the
front of carpet washer and slide the nozzle into place.

Push the nozzle release
clip to lock the nozzle.

To prevent excessive build up of dirt
/debris in the nozzle, always dry
vacuum before using the carpet washer.

TIP

13

Let’s talk technical

CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

Cleaning the SpinScrub brushes

Remove the tanks and lie
the washer on its back
exposing the SpinScrub
brushes.

Leave the brushes to fully
dry before reassembling.
Push the cover onto the
clips until they click into
place.

Firmly pull the sides of
the SpinScrub brushes
to remove.

Line up the spindle
and tabs on the side of
SpinScrub brushes into
carpet washer, push
rmly until it clicks into
place.

Depress the clips to
release the SpinScrub
cover and rmly pull the
cover to remove.

The SpinScrub brushes
can be removed and
cleared of any debris/
threads or hair. Rinse
under water to remove
debris.

14

Cleaning the SpinScrub lter

Let’s talk technical

Remove both tanks and
tilt the carpet washer
so it is lying on its back.

Lift the nozzle release clip
to unlock the nozzle.

Hold the front of the
nozzle and push down to
release the nozzle away
from the washer, once
released lift to remove.

A blocked/dirty SpinScrub
lter will cause the SpinScrub
brushes to slow.

Wipe any dirt and debris
from the mesh lter.

IMPORTANT

15

What to do if it goes wrong

CAUTION: To reduce the risk of personal injury, unplug the carpet washer before performing maintenance/

troubleshooting checks.

SolutionProblem

• Check the contents panel on the box to make sure the part is denitely included

Is there an
accessory missing?

Why won’t the carpet
washer turn on?

Why won’t the
solution/clean
water dispense?

with this carpet washer.

• The plug may not be fully pushed into the electrical socket.

• Check if the fuse in the plug needs replacing. Always replace with a
British 13amp fuse.

• Make sure the clean water tank is tted securely. Go to ‘Using your machine’.

• Squeeze the trigger on the handle to release solution and water mix.
Go to ‘Using your machine’.

• Water/solution tank is empty, rell. Go to ‘Using your machine’.

• Wash/Rinse dial has been set to 'rinse'. Set dial to 'wash' to dispense solution.

• The clean water tank valve may be stuck. Hold the clean water tank over the sink
and press the valve underneath to release.

Why won’t the
carpet washer
pick up?

Why won’t the
brushes spin?

16

• The oat in the dirty water tank may have been activated. Empty the dirty water
tank and wait for the oat to settle before re-starting your carpet washer.

• The hose connector cover has not been correctly closed. Correctly close cover.

• The dirty water tank may not be tted correctly. Re-t making sure the lid
is pushed down securely. Go to ‘Taking care of your machine’

• Check the nozzle for blockages and clear. Go to ‘Taking care of your machine’.

• Check the nozzle is correctly tted. Go to ‘Taking care of your machine’.

• The brushes will only spin when the carpet washer is reclined.

• Check the SpinScrub brushes and brushbar for blockages and clear.

• Check for damage to the brushbar and the spindle on the back of the

SpinScrub brush.

• The SpinScrub lter is blocked, wipe clean. Go to ‘Taking care of your machine’.

Getting in touch

† Registration required. Terms and conditions apply, see vax.co.uk for details.

17

Accessories

Don’t forget your accessories!

Order at: www.vax.co.uk/spares-and-solutions

Platinum (1.5l)
1-9-139136

Platinum (4l)
1-9-142060

Platinum Carpet Cleaning Solution deep cleans carpets and removes stubborn stains.
Safe to use on wool carpets - Woolsafe approved.

18

Notes

19

GET IN TOUCH

[e-mail] vax.co.uk

EU Statement of Compliance: Manufacturer/EU importer: VAX Limited, hereby on our own responsibility, declare that the
ECGLV1B1, CWGRV011, CWGRV021 and CDCW-RPXR are manufactured in compliance with the following Directives: Safety:
2014/35/EU Low Voltage Directive. EMC: 2014/30/EU Electromagnetic Compatibility Directive.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.

© 2019 VAX Limited. All rights reserved. The VAX trade mark and VAX lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.

VAX Ltd, Pointon Way, Stonebridge Cross Business Park, Hampton Lovett, Droitwich, WR9 OLW, UK