Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using the
carpet washer. Always fully extend
the mains cable before use.
www.vax.co.uk
UPRIGHT CARPET WASHER
Vax Model Number: V-023
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 1
1 Handle
2 Power on/off
3 Clean water tank latch
4 Clean water tank
5 Dirty water tank latch
6 Dirty water tank handle
7 Dirty water tank
8 Floating Brushbar
9 Dirty water tank door
10 Dirty water tank lid
11 Solution tube clip
12 Power cord
13 Lower cord wrap with
quick cord release
14 Handle release pedal
15 Solution tube port
16 Tool caddy
17 Carry handle
18 Cord wrap
19 Hose wrap
20 Vax AAA Carpet Cleaner
750ml
1. Diagram
Parts Overview
Attachments
22 Solution tube
23 Upholstery/stair hose adaptor
24 Upholstery/stair hose
25 Upholstery/stair attachment
26 Solution spray trigger
27 4x Nuts
28 1x Tool caddy screw
29 2x Mid-section screws
30 1x Upper handle screw
26
30
28
27
25
23
22
24
1
2
W
Fig.1/1
Fig.1/4
Fig.1/5
Fig.1/3
Fig.1/2
20
29
2
3
4
5
6
7
9
10
8
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 2
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the carpet washer, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is necessary
when used by or near children or the infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. If the supply
cord and/or plug is damaged, they must be replaced
by the manufacturer, a Vax Service Agent or similarly
qualified persons in order to avoid hazard.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate with
openings blocked, keep them free of anything that
may reduce airflow.
10.Keep hair, loose clothing fingers and all parts of
the body away from openings and moving parts.
11. Do not use the carpet washer on any glowing,
burning or smoking particles.
12. Do not use without the solution tank and dirty
water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the carpet washer on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent
tripping accidents.
19. Using improper voltage may result in damage
to the motor and possible injury to the user.
The correct voltage is listed on the rating label.
20. A hazard may occur if the carpet washer runs over
the power supply cord.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
NOTE: If the supply cord is damaged, it must be
replaced by the manufacturer, a Vax service agent or
similarly qualified persons in order to avoid hazard.
Safety Information/Use & Function
3
NOTE: The carpet washer must be unplugged from
the electrical outlet after use, and before cleaning or
maintaining the carpet washer.
IMPORTANT: This carpet washer is not intended for
commercial use.
3. Use & Function
Assembling the Carpet Washer
1. Stand base in upright position. Push mid-section onto
base by aligning tabs on inside of mid-section with the
base (Fig.3/1).
2. Insert the two (2) nuts into the recesses located on
the left and right sides of the base. While holding the
nuts in place, insert the two (2) medium length
screws through the front of the mid-section and
tighten (Fig.3/2).
Fig.3/2
Fig.3/1
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 3
3. Slide upper handle down onto unit. Insert the nut
into the recess in the back of the upper handle.
While holding the nut in place, insert the long
screw through the front of the upper handle and
tighten (Fig.3/3). Run the mains wire above the
upper cord hook and secure with the cord clip.
4. Align tool caddy with screw holes on mid-
section and base (Fig.3/4).
5. Place nut into recess on tool caddy and hold
into place (Fig.3/5). Press handle release with
other hand to tilt the mid-section backwards
(Fig.3/5A).
Fig.3/4
Fig.3/3
4
Use & Function
6. Place screw through centre of lower mid-section
and tighten (Fig.3/6).
Hose & Tool Storage
1. Detach the upholstery hose adaptor from the end
of the hose and slide it onto the adaptor post
(Fig.3/7).
Fig.3/7
Fig.3/6
Fig.3/5
Fig.3/5A
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 4
Use & Function
2. Slide the upholstery attachment into the middle
slot of the lower tool caddy (Fig.3/8).
3. Slide the adaptor end of the hose into the left
slot on the lower tool caddy. Be sure to line up
the pushpin with the slot and press down until
secure in place (Fig.3/9).
4. Run the hose to the upper caddy and press into
hose clip #1 (Fig.3/10).
Fig.3/10
Fig.3/9
Fig.3/8
5. Continue wrapping the hose clockwise around
the tool caddies, pressing the hose into the
groove on the bottom of the lower tool caddy
(Fig.3/11).
6. Run the hose back to the upper caddy and press
into hose clip #2 (Fig.3/12).
7. Lock the attachment end of the hose into place
by pressing down onto the post located on the
right side of the lower tool caddy, until secure in
place (Fig.3/13).
Fig.3/13
Fig.3/12
Fig.3/11
5
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 5
Preparing the Carpet/How to Operate
6
4. Preparing the Carpet
IMPORTANT: The carpet washer is not a dry vacuum
cleaner.
1. Vacuum carpet thoroughly. Use a vacuum
cleaner with a revolving brushbar for best
results.
2. Remove as much furniture from the room as
possible. If unable to remove the furniture, place
plastic or foil under and around the legs until the
carpet has dried completely.
HELPFUL HINTS FOR CLEANING CARPET:
1. Only use Vax AAA Carpet Cleaner with this carpet
washer.
2. Do not oversaturate carpet with cleaning solution
while using the carpet washer.
3. For heavily soiled areas, additional applications
may be necessary.
4. Allow plenty of time to dry carpet thoroughly.
5. Wipe cleaning solution from woodwork and wood
to prevent any damage.
6. Try not to walk on carpet until it is completely dry.
7. After carpet is thoroughly dry, vacuum the carpet
using a vacuum cleaner with a revolving brushbar.
8. Before cleaning, determine where to start and
end, making sure not to walk over previously
cleaned areas.
CHECK FOR COLOUR FASTNESS:
Before cleaning carpet, test for colour fastness.
Dampen a white cloth with solution. Test on an
inconspicuous area. Gently rub the cloth over the area.
Check each colour for colour bleeding. If the cloth
remains clean, it should be safe to clean the carpet.
AFTER CLEANING:
• Allow carpet to dry completely. Try not to walk on the
carpet until it is dry.
• If it is necessary to walk on the carpet, place white
towels on the areas to be walked on.
• If the carpet is not dry and the furniture must be
placed back in the room, use plastic or foil under the
furniture to prevent staining the carpet.
• Thoroughly clean the dirty water tank with warm
(max 40
o
C) tap water.
5. How to Operate
IMPORTANT: Turn off the carpet washer when
emptying and filling the reservoir.
1. Grasp clean water tank under the handle while
pressing clean water tank latch. Tilt clean water
tank away from cleaner and remove (Fig.5/1).
2. Unscrew measuring cap from back side of clean
water tank (Fig.5/2).
3. Fill the tanks measuring cap with solution
(approximately 4 capfuls). Pour into clean water
tank (Fig.5/3).
Fig.5/3
Fig.5/2
Fig.5/1
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 6
7
NOTE: Use only Vax AAA Carpet Cleaner solution.
Using other cleaning solutions may cause excess
foaming. Excessive foam will cause the float to shut off
the carpet washer prematurely. Using other solutions
will void the warranty.
6. Accessories
For Cleaning Upholstery and Stairs
1. Put carpet washer in its upright position, then turn
off. Connect the upholstery attachment to the
trigger adaptor (Fig.6/1).
2. Remove the dirty water tank door from the top
of the dirty water tank (Fig.6/2).
3. Insert the upholstery/stair hose adaptor into the
opening on top of the dirty water tank (Fig.6/3).
Fig.6/3
Fig.6/2
Fig.6/1
4. Connect the hose solution tube into the fitting on
the lower left side of handle facing carpet washer
(Fig.6/4).
Attachment Usage
Turn the power on/off switch to on. While depressing
solution spray trigger, pull attachment in backward
motion (Fig.6/5). Release trigger and push attachment
forward in the same path to remove dirty water and
solution from upholstery. (For heavily soiled areas,
repeat if necessary.)
NOTE: Do not oversaturate the upholstery.
IMPORTANT: For best cleaning results use steady,
moderate, forward and backward motion. Make sure
upholstery is dry before use.
NOTE: If the dirty water tank door is not replaced,
there will be no suction through the floor nozzle and
the unit will not operate properly.
Fig.6/5
Fig.6/4
How to Operate/Accessories
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 7
8
Emptying & Cleaning the Dirty Water Tank & Filter
7. Emptying & Cleaning the
Dirty Water Tank & Filter
The carpet washer is equipped with a shut off valve
within the dirty water tank. When the dirty water tank
becomes full, the float will rise, shutting off the air flow
through the nozzle.
NOTE: The float in the carpet washer will shut off the
suction when the dirty water tank is full. For best
results, use smooth, steady motion keeping the nozzle
flat against the carpet. Tipping the carpet washer and
breaking the seal of the nozzle and carpet will cause
the float to rise and shut off the suction. Once the float
is activated, empty the dirty water tank. If the dirty
water tank does not appear full, turn the unit off and
wait for the float to settle. Turn the unit back on and
resume cleaning. If the float repeatedly shuts off the
suction, empty the dirty water tank and rinse away any
foam. For best results, use only Vax AAA Carpet
Cleaner. Other solutions may generate excessive foam
which will cause the float to rise prematurely and shut
off the suction. Use four (4) capfuls of Vax AAA Carpet
Cleaner per fill up of the clean water tank. A higher
concentration of carpet cleaner may cause excessive
foaming.
NOTE: There will be a noticeable change in the pitch
of the cleaner. This indicates a need to empty the dirty
water tank.
WARNING: To reduce the risk of injury from moving
parts - unplug before emptying the dirty water tank.
1. Grasp top of dirty water tank handle and push
latch to release (Fig.7/1).
Fig.7/1
2. Grasp handle and pull tank out of base (Fig.7/2).
3. Remove dirty water tank lid (Fig.7/3).
4. To empty dirty water tank, grasp handle with one
hand and nozzle with the other and empty into
sink. To clean, rinse tank thoroughly with clean
water and let dry (Fig.7/4).
Fig.7/4
Fig.7/3
Fig.7/2
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 8
9
5. Rinse dirty water tank and filter with lukewarm
(max 40ºC) water. Wipe and let dry thoroughly
before storing to prevent mildew from forming.
The foam filter can be removed for easier
cleaning and air drying (Fig.7/5).
NOTE: Do not use any chemicals when cleaning.
Replacing dirty water tank in base of
carpet washer
6. While making sure the front of the dirty water tank
is resting on the base, place the rear of the tank
into the base of the cleaner (Fig.7/6).
7. Push handle down until it latches (Fig.7/7).
NOTE: Do not store cleaner with solution in reservoir
or dirty water in dirty water tank. Mineral deposits and
mildew can form which will affect the performance of
the carpet washer.
Fig.7/6
Fig.7/5
8. Storage
Transporting & Storing Carpet Washer
Storing Tools
Place hose and upholstery attachments into their
storing locations (Fig.8/1). Store for next use.
Fig.8/1
Fig.7/7
Emptying & Cleaning the Dirty Water Tank & Filter/Storage
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 9
Storage/Brush Removal & Replacement
10
Carry Handle
Grasp the handle on the back of the washer to move
it from room to room (Fig.8/2).
BEFORE STORING CARPET WASHER:
1. Empty and rinse clean water tank and dirty
water tank.
2. Replace empty clean water tank and dirty water tank.
3. Ensure that brushes and underside of unit are fully
dry prior to storing on a carpeted or
wood surface.
NOTE: Do not store or transport unit with a full clean
water tank or dirty water tank.
9. Brush Removal &
Replacement
Tool required: Phillips screwdriver
WARNING: To reduce the risk of injury from moving
parts, unplug before servicing.
1. Remove the water, switch off and unplug carpet
washer. Flip the cleaner on its side to expose the
nozzle base (Fig.9/1).
Fig.9/1
Fig.8/2
2. To remove the brush access cover, use a Phillips
screwdriver to remove the two (2) screws
(Fig.9/2).
3. Lift out the floating brushbar (Fig.9/3).
4. Replace floating brushbar (Fig.9/4).
Fig.9/4
Fig.9/3
Fig.9/2
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 10
11
Brush Removal & Replacement
5. Replace the brush access cover by inserting the
end furthest from the brush first. Then replace the
front end before securing in place with the two (2)
screws (Fig.9/5).
Fig.9/5
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 11
10. Troubleshooting
WARNING: TO REDUCE RISK OF PERSONAL INJURY, UNPLUG CARPET WASHER BEFORE
SERVICING
PROBLEM: Carpet washer won’t pick-up or low suction
Cause: The dirty water tank door is not installed.
Solution: Insert the dirty water tank door.
Cause: The dirty water tank door is not installed correctly.
Solution: Review placing dirty water tank in base of carpet washer.
Cause: The dirty water tank is full.
Solution: Empty the dirty water tank.
Cause: The dirty water passage clogged.
Solution: Clean the dirty water tank.
PROBLEM: Water escaping from carpet washer
Cause: The dirty water tank is full.
Solution: Empty the dirty water tank.
Cause: The dirty water tank is not installed correctly.
Solution: Review placing dirty water tank in base of cleaner.
Cause: The clean water tank is not installed properly.
Solution: Review clean water tank installation.
PROBLEM: Carpet washer won’t dispense solution
Cause: The clean water tank is not installed properly.
Solution: Review How to Operate.
Cause: The carpet washer needs a service.
Solution: Take it to service centre or contact Vax Careline.
PROBLEM: Carpet washer attachments won’t pick up
Cause: The hose is clogged.
Solution: Remove the hose and tools; remove obstruction.
Cause: The dirty water tank is full.
Solution: Empty the dirty water tank.
PROBLEM: Carpet washer attachments won’t spray
Cause: The solution tube is not connected properly.
Solution: Connect the solution tube properly.
12
Troubleshooting
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 12
13
UK Service & Help/Technical Specification
12. Technical Specification
Power supply: 220-240V~50Hz
Motor power: 600W
Clean water tank volume: 3.5 litres
Dirty water tank volume: 2.5 litres
Filter system: Foam block
Cord length: 7.5m
Weight: 7.1kg
Subject to technical change without notice.
11. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone is available out of these hours.
Any queries or concerns about using the Vax, call
the Vax Careline. Calls are charged at the UK
national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There
are over 400 approved Vax Service Agents in the
UK. For the nearest Service Agent, please call the
Vax Careline.
www.vax.co.uk
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 13
14
This page has been left intentionally blank.
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 14
15
This page has been left intentionally blank.
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 15
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the product
V-023 Rapide Supreme is manufactured in compliance with the following Directives:
Safety: 73/23/EEC Low Voltage Directive
EMC: 89/336/EEC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Lsd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
Version 1
Vax V-023 D6 mm.qxd 9/8/05 10:34 AM Page 16
Loading...