Page 1
Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using
the carpet washer. Always fully
extend the mains cable before use.
Please retain these instructions
for future reference.
www.vax.co.uk
Upright Carpet Washer
Vax Model Number: V-021
V-021 User Guide.qxd 5/6/06 4:14 pm Page 2
Page 2
Fig.1/2
1. Diagram
Parts Overview
6
2
1
9
11
12
3
7
10
13
14
8
5
2
1. Handle
2. Clean Water Tank Release
Button
3. Clean Water Tank
4.
Dirty Water Tank Latch
5. Dirty Water Tank Handle
6.
Exhaust Filter
7.
Brushbar
8. Dirty Water Tank
9. Solution Release Trigger
10. Power Cord Tidy
11.
Power Cord Holder
12. Power Cord
13.
Power Switch
14. Handle Release Pedal
15.
Bottle of Spring Clean
4
Fig.1/1
AAA
ANTI
ALLERGEN
ADDITIVE
spring
carpet cleaner
INCLUDES
clean
15
Fig.1/3
V-021 User Guide.qxd 5/6/06 4:14 pm Page 3
Page 3
3
S
afety Information/Preparing the Carpet
2. Safety Information
FOR HOUSEHOLD USE ONLY
When using the carpet washer, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. If the
supply cord and/or plug is damaged, they must
be replaced by the manufacturer, a Vax Service
Agent or similarly qualified persons in order to
avoid hazard.
6. Do not pull or carry by the cord, use the cord as
a handle, allow the cord to come into contact with
hot or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked, keep them free of
anything that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
11. Do not use the carpet washer on any glowing,
burning or smoking particles.
12. Do not use without the solution tank and dirty
water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the carpet washer on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent
tripping accidents.
19.
Using impr
oper voltage may result in damage to
the motor and possible injury to the user
. The
correct voltage is listed on the rating label.
20. A hazard may occur if the carpet washer runs
over the power supply cord.
NOTE: Carpets should be dry vacuumed
thor
oughly before washing.
NOTE: If the supply cord is damaged, it must be
replaced by the manufacturer, a Vax service agent or
similarly qualified persons in or
der to avoid hazar
d.
NOTE: The carpet washer must be unplugged from
the mains socket outlet after use, and before
cleaning or maintaining the carpet washer.
IMPORTANT: This carpet washer is not intended
for commercial use.
3. Assembling the Machine
Components
Fig.3/1 - Base Unit
Fig.3/2 - Mid-Section
Fig.3/3 - Handle
Fig.3/4 - 3 Screws
V-021 User Guide.qxd 5/6/06 4:14 pm Page 4
Page 4
Assembly
1. Line up mid-section with base unit and slot into
place (as shown).
2. Insert handle into mid-section ensuring that the
solution trigger is at the back of the machine and
the screw hole in the handle is lined up with the
scr
ew hole in the mid-section (as shown).
3. Insert and tighten screws as indicated.
4. Twist cord holder until it is facing upwards.
5. Finally insert clean water tank and machine is fully
assembled.
Preparing the Machine/Assembly
4
Fig.3/8
Fig.3/9
Fig.3/5 - Clean Water Tank
Fig.3/6
Align screw holes
Insert Screw Insert Screw
Insert Screw
Fig.3/10 Fig.3/11
V-021 User Guide.qxd 5/6/06 4:14 pm Page 5
Page 5
4. Preparing the Carpet
IMPORTANT: Do not use the carpet washer as a
dry vacuum.
1. Vacuum carpet thoroughly. Use a vacuum cleaner
with a revolving brushbar for best results.
2. Remove as much furniture from the room as
possible. If unable to remove the furniture, place
plastic or foil under and around the legs until the
carpet has dried completely.
HELPFUL HINTS FOR CLEANING CARPET:
1. Only use Vax AAA Carpet Cleaner with this carpet
washer.
2. Do not oversaturate carpet with cleaning solution
while using the carpet washer.
3. For heavily soiled areas, additional applications
may be necessary.
4. Allow plenty of time to dry carpet thoroughly.
5. Wipe cleaning solution from woodwork and wood
to prevent any damage.
6. Try not to walk on carpet until it is completely dry.
7. After carpet is thoroughly dry, vacuum the carpet
using a vacuum cleaner with a revolving brushbar.
8. Before cleaning, determine where to start and
end, making sure not to walk over previously
cleaned areas.
CHECK FOR COLOUR FASTNESS:
Before cleaning carpet, test for colour fastness.
Dampen a white cloth with solution. Test a small area
in a closet. Gently rub the cloth over the area. Check
each colour for colour bleeding. If the cloth remains
clean, it should be safe to clean the carpet.
AFTER CLEANING:
• Allow carpet to dry completely. Try not to walk on
the carpet until it is dry.
• If it is necessary to walk on the carpet, place
white towels on the areas to be walked on.
• If the carpet is not dry and the furniture must be
placed back in the room, use plastic or foil under
the furniture to prevent staining the carpet.
•
Thor
oughly clean the dirty water tank with warm
(max 40ºC) tap water.
5. Preparing the Machine
1. Hold the handle of the clean water tank and press
‘Clean Water Tank Release’. Tilt Clean Water
Tank away from the carpet washer and remove.
2. Unscrew the measuring cap from the reverse
side of the clean water tank. Fill measuring cap
with solution (Use only 1 capful of solution per
full tank). Pour into clean water tank.
IMPORTANT: Use only Vax AAA Carpet Cleaner
solution. Using other cleaning solutions may
cause excess foaming. Excessive foam will
prevent the machine from working effectively.
Using other solutions will void the warranty.
Assembly/Usage
5
Fig.5/1
Fig.5/2
V-021 User Guide.qxd 5/6/06 4:14 pm Page 6
Page 6
3. Fill remainder of clean water tank with warm
(max 40°C) tap water. Replace cap.
4 Place bottom of clean water tank into carpet
washer and push back until it locks into place.
6. Usage
Plug cord into electrical socket. Turn on the machine
by using the on/off switch located on the side of the
machine.
IMPOR
T
ANT: Never leave unit unattended with
power on. Turn off when emptying and filling
tanks. Do not over-saturate the carpet
1 Step onto handle release pedal to put the
machine into cleaning position (Fig.6/1).
While depressing the solution spray trigger, pull
carpet washer in a backward motion. Release
the trigger and push the unit forward in the
same path to agitate and remove dirty water
and solution from carpet. (For more heavily
soiled ar
eas, repeat if necessary).
IMPORTANT: For best cleaning results use a
steady, moderate, forward and backward motion.
Always work from back to front across the room to
avoid stepping on wet carpet and lowering the pile.
2 When dirty water tank is full lift dirty water tank
latch and remove from base unit using the
handle.
3 Twist dirty water tank outlet cap to the left and
remove, empty, rinse and replace.
Troubleshooting
6
Fig.5/4
Fig.6/1
Fig.6/2
Fig.6/3
Fig.5/3
V-021 User Guide.qxd 5/6/06 4:14 pm Page 7
Page 7
4 When finished cleaning remove the dirty water
tank and rinse with warm water and allow it to
dry before storage. Also remove filter (as
shown) rinse with warm water and allow it to dry
thoroughly before storing.
IMPORTANT: Do not use any chemicals when
cleaning.
NOTE: Do not store cleaner with solution in clean
water tank or dirty water in dirty water tank.
Mineral deposits and mildew can form with will
affect the performance of the carpet washer.
7. Troubleshooting
WARNING: To reduce risk of personal injury,
unplug carpet washer before servicing.
Problem: The cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in firmly.
Cause: No electricity in electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
8. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone will be available out of these hours.
Any queries or concerns about using your Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of your carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For
the nearest Vax Service Agent, please call the Vax
Careline or visit
www.vax.co.uk
9. Technical Specification
Voltage: 220 ~ 240V 50Hz
Motor Power: 550W
Clean water tank volume: 2.6 litres
Dirty water tank volume: 2.4 litres
Cord length: 6.1m
Weight: 5.7kg
7
Fig.6/4
Fig.6/5
Fig.6/6
V-021 User Guide.qxd 5/6/06 4:14 pm Page 8
Page 8
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility declare that the product
V-021 Rapide Spring is manufactured in compliance with the following:
Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC
EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC
W
aste electrical pr
oducts should not be disposed of with household waste. Please r
ecycle wher
e
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
email: info@vax.co.uk - website: www.vax.co.uk
V
ersion 1
V-021 User Guide.qxd 5/6/06 4:14 pm Page 1
Loading...