PROVEN TO CLEAN BETTER
THAN THE LEADING RENTAL
LET’S GET STARTED.
ECB1SPV1
Let’s talk safety
Basic
safety
precautions
Don’ts
This carpet washer is intended for household use only and NOT
for commercial or industrial use.
• Only use the carpet washer indoors and keep the area you’re
cleaning well lit.
• Keep ngers, hair and loose clothing away from moving parts
and openings whilst using the carpet washer.
• Before using the carpet washer test your carpets/rugs/upholstery
for colourfastness and pile distortion.
• Don’t leave the carpet washer plugged in when unattended.
• Don’t use the carpet washer if it has been dropped, damaged or
left outdoors.
• Don’t run over the power cord or use the carpet washer if the
power cord or plug is damaged. If the supply cord is damaged,
it must be replaced by the manufacturer, its service agent or
similarly qualied persons in order to avoid a hazard.
• Don’t use the carpet washer to pick up any ammable or
combustible materials (lighter uid, petrol, kerosene etc.) or use
the carpet washer in an area with explosive vapours or liquid.
• Don’t handle the plug or use the carpet washer with wet hands.
• Don’t pull or carry the carpet washer by the power cord.
Do’s
• Check with the manufacturer of your ooring prior to using the
carpet washer.
• The clean water tank should be lled with warm water
(max 40°C) only. Filling the clean water tank with hot or boiling
water will damage the machine and invalidate the guarantee.
• Always vacuum your ooring thoroughly before using the
carpet washer.
• Test all carpets/rugs/upholstery before full usage. Run the carpet
washer over a small hidden area. If no damage or pile distortion
occurs continue cleaning.
• Always replace the fuse in the plug with a British 13amp fuse.
• Always unplug the carpet washer before carrying out any
maintenance and before connecting or disconnecting the
hose/accessories.
• Always check tools and accessories are free from damage,
dirt and debris before using.
• Take extra care when cleaning on the stairs.
• Always protect the power cable from heated surfaces or near
open ames.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
• Only Vax recommended tools and solution should be used with this carpet
washer. Using other solutions may invalidate the guarantee.
• Don’t use the carpet washer to pick up hot coals, cigarette butts, matches or
smoking hot burning items or use in an area where there may be harmful uids
(chlorine, bleach and ammonia drain cleaner).
• Don’t use the power cord as a handle, pull the power cord around corners or
sharp edges, or close a door over the power cord.
• Don’t unplug the carpet washer by pulling on the power cord.
• Don’t carry the carpet washer while it’s switched on.
• Don’t attempt to remove blockages with sharp objects as this may cause
damage to the carpet washer.
• Don’t use the carpet washer with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
• Turn o all controls on the carpet washer before disconnecting or connecting
the power cord. After use always wrap the power cord around the cord
clips provided.
• Always keep the power cord away from the brushes whilst using the
carpet washer.
• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat. Care should be taken to arrange the extension cord as it can
be a trip hazard.
• Always use the carpet washer with all water/solution tanks and lters in place.
• Keep all openings clear and free from debris as this may aect the
airow/suction.
• Always use the carpet washer in an upright position. To prevent motor damage
from dirty water, never hold the carpet washer upside down or on its side.
• Store the carpet washer in a cool, dry area. Before storing the carpet
washer please ensure all water/solutions tanks and lters are thoroughly
clean and dry.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY AS
INSTRUCTED IN THIS GUIDE.
Thank you for buying this Platinum PowerMax.
Taking care of your carpets
The Platinum PowerMax is designed to make washing carpets regularly, as eective and ecient
as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets will ensure they keep their appearance for longer and smell fresh and
clean. You’ve chosen carpets for your home for a reason and Vax will help you take good care
of them.
Taking care of your Platinum PowerMax
Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets.
We’re here if you need us
Instead of taking me back to the shop,
simply visit our online support:
vax.co.uk/support
Still need to get in touch?
Our UK based Customer Care Team are here to support you.
For help with assembly, operational or performance problems, or buying and tting new accessories,
you can nd all our contact details at vax.co.uk/contact
This user guide can be found online at: vax.co.uk/support
Contents
Let’s talk safety
Getting to know your machine
Included with
your machine
Hose
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
What to do if it goes wrong
Getting in touch
Accessories
Notes
Upholstery wash tool
SpinScrub tool
Pre-treatment wand
Hard oor squeegee
2 x 250ml
Platinum solution
Pre-treatment solution
Accessory bag
Handle
Boost trigger
SpinScrub tool and caddy
Clean water/solution tank
release button
Solution trigger (hidden)
Clean water/solution tank caps
Clean water/solution tank
Rinse/Wash dial
Dirty water release latch
Dirty water tank
Hose and solution
connection port (hidden)
Nozzle release clip
Quick Clean function
Nozzle
SpinScrub brushes
and brushbars
Quick cord
release hook
Handle lock dial
Recline pedal
On/O
pedal
Technical Specication
Name Vax Platinum PowerMax
Code ECB1SPV1
Cord length 9m
Weight 9.5kg
Wattage: See rating label on machine for details.
Voltage: See rating label on machine for details.
Subject to technical change without notice.
Accessories & Consumables
SpinScrub Tool
1-9-133245-00
Upholstery Wash Tool
1-9-136232-00
*To purchase consumables and accessories, please visit vax.co.uk
Getting started
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
IMPORTANT: Carpets should be dry vacuumed thoroughly before washing.
• Test for colourfastness - Wet a white absorbent cloth with the solution. In a small hidden area of your carpet/rugs/
upholstery, gently rub with the dampened cloth. Wait ten minutes and check for colour removal or bleed with white
paper towel or cloth. Check all carpets/rugs/upholstery material before rst use and if your carpet has more than
one colour, check all colours.
• Test all carpets/rugs/upholstery before full usage. Run the carpet washer over a small hidden area. If no damage or
pile distortion occurs continue cleaning.
• When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture cannot be moved,
place aluminium foil or wax paper under the legs. This will prevent wood nishes from staining your carpet. Pin up
furniture skirts and curtains.
• When using the carpet washer, basic safety precautions should always be observed and don’t over saturate
your carpets.
• Only use Vax carpet solution. Using other solutions may cause excess foaming and will invalidate your guarantee.
• The clean water tank should only be lled with warm water (max 40�C). Filling the clean water tank with hot/
boiling water will damage your machine and invalidate the guarantee. This is a powerful carpet washer, before
plugging in make sure all controls are turned o also hold carpet washer rmly when staring and during use.
Assembling your carpet washer
Stand the base of the carpet
washer on the oor in the
upright position. Line up the
handle with the main body
and push into place.
Line up the SpinScrub tool
with the holder and slide the
tool downwards into place.
Turn handle lock dial
clockwise to lock
in position.
Assemble the tanks by tilting
and lining up the front of
the tank to the washer and
pushing the tank back until
it clicks into place.
Slide the SpinScrub tool
holder over and down
the handle.
Using your machine
NOTE: Carpets should be dry vacuumed thoroughly before washing. For heavily soiled areas, it may be necessary
to repeat the cleaning process. Make criss-crossing strokes across the original pattern and overlap with each pass.
Filling the water/solution tank and cleaning modes
Press the clean water/
solution tank release
button, pull and lift to
remove the tank.
Tilt and line up the front of
the tank to the washer and
push the tank back until it
clicks into place.
This machine has an auto mix tank so any solution
not used can be poured back into the bottle.
Twist the water/solution
tank cap anti-clockwise
and remove.
Turn the wash/rinse dial
to ‘wash’. The SpinScrub
brushes and brushbar
deep clean your carpets
with water and solution
removing dirt and stains.
Pour the required amount
of carpet cleaning solution
into the tank. Tighten the
cap before returning the
tank to the washer.
Plug into the mains,
press the On/O button
to switch on.
TIP
Fill the clean water tank
with warm water (max
40°C). Fill to max ll line
for a Deep Clean, and ll to
the Quick Clean ll line for
a quick surface clean.
Choose the cleaning
mode by turning the dial
on the base.
Quick Clean Mode:
Best for a quick, surface
clean - carpets dry in
less than an hour.
Deep Clean Mode:
Best overall results for
a thorough, deep clean.
Using your machine
IMPORTANT: Your dirty water tank is tted with a oat. When the dirty water tank is full, or the oorhead is not in
contact with the carpet, the oat will shut o the suction on the carpet washer. You will be able to hear if this has
happened as the motor noise on the machine will increase. Once the oat is activated, empty the dirty water tank if full.
If the dirty water tank is not full then turn o your machine at the power switch and wait for the oat to settle.
Press the recline pedal
and pull handle backwards.
For tough stains press
the boost trigger together
with the solution trigger
to release more water/
solution mix.
Squeeze the trigger
to release the solution
and water mix.
Turn the wash/rinse dial
to ‘rinse’. Only water
is released to remove
solution residue.
For best results apply water/solution on
the forward stroke and release the trigger
on the backward stroke to pick up water/
solution. For a dryer nish, follow with an
additional dry stoke with no trigger pressed.
For best cleaning results use
slow straight parallel strokes.
Intermittent dry forward
strokes will increase water
pick up. The ‘rinse’ mode
will also work when using
the hose.
TIP
Using your machine
Using the hose and tools
NOTE: The carpet washer should be in the upright position when using the hose and tools; this will de-activate
the SpinScrub brushes and brushbar.
Pour the required amount
of carpet cleaning
solution into the tank.
Push the hose end and
hose solution connector
into the hose and solution
connection port.
Fill the clean water tank
with warm water
(max 40°C).
Select the SpinScrub or Upholstery tool. Slide the tool
over the tab at end of the hose until it clicks into place.
Turn the wash/rinse dial
to ‘wash’.
Pull down the accessory
hose connector cover.
Plug into the mains and
press the On/O button
to switch on.
Use the carpet washer
or hose to pick up spills
before washing and
cleaning the area.
TIP
Press the trigger on the hose
to release solution/water.
Squeeze the trigger on the forward stroke and release the trigger
on the backward stroke to pick up water/solution. For a dryer nish,
follow with an additional dry stoke with no trigger pressed.
Using your machine
Using the pre-treatment wand
Pre-treating your carpet before washing will help to remove stubborn stains. Do not saturate your carpet.
Pour the required amount
of pre-treatment solution
into the tank.
Push the wand connector
into the solution tube port.
Fill the clean water tank
with warm water
(max 40°C).
Plug into the mains and
press the On/O button
to switch on.
Turn the wash/rinse dial
to ‘wash’.
Press and hold the trigger
on the pre-treatment
wand, spraying evenly
over stubborn atains
Pull down the accessory
hose connector cover.
Leave the solution for
10-15 minutes before
washing carpet.
Using your machine
CAUTION: To prevent damage to wood oors and other hard oors, follow the ooring manufacturer's
cleaning recommendations. Inspect the oor surface for a worn nish, bare wood or separated joints.
It is not recommended to use the carpet washer on oors if any of these conditions exist. Test on an
inconspicuous area rst
Washing hard oors
IMPORTANT:
Before attaching the hard oor squeegee onto the carpet washer, either remove the tanks or make sure the tanks are
empty before lying the carpet washer on its back.
Pour the required amount
of solution into the tank.
Lie the carpet washer on
its back and line up the
squeegee with the nozzle.
Hard oors should be dry vacuumed thoroughly before washing.
Fill the clean water tank
with warm water
(max 40°C).
Hold the front of the squeegee onto the
edge of the nozzle and push the squeegee
under the nozzle until it clicks into place.
For best results, clean hard
oors in Quick Clean Mode
TIP
Using your machine
CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.
Emptying and cleaning the dirty water tank
IMPORTANT: Empty and rinse out clean and dirty water tanks and leave to air dry before replacing.
Do not leave solution stored in the tanks between uses.
Press the dirty water
tank release latch and
pull the tank to remove.
Clean the lter screen
located at the back of the
dirty water tank.
Pull and lift the dirty water
tank clip to release the lid.
Lift the tank lid to remove.
To re-t, tilt the dirty water tank
and line the front of the tank up
onto carpet washer. Push back
until it clicks into place.
Empty the dirty water over the sink. Rinse
the dirty water tank and lid under water
(max 40°C) to remove dirt/debris.
Taking care of your machine
CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.
Removing and cleaning the nozzle
Remove both tanks and tilt
the carpet washer back.
IMPORTANT: If the nozzle is tted incorrectly, this will cause poor dirty water pick up.
Lift the nozzle release clip
and pull the nozzle forward,
separating the tabs on the
nozzle and carpet washer.
Rinse the nozzle under
water to remove dirt/debris.
To replace the nozzle, line
up the tabs on the nozzle
with the tabs underneath the
front of the carpet washer.
Push the nozzle down until
it clicks into place.
Taking care of your machine
Removing and cleaning the SpinScrub brushes
Lie the carpet washer on its
back exposing the SpinScrub
brushes and brushbar.
Carpets and hard oors should be dry
vacuumed thoroughly before washing.
This will help prevent excessive build
up of dirt/debris in the nozzle.
Firmly pull the sides
of the SpinScrub
cover and remove the
SpinScrub brushes.
TIP
Using a pair of scissors,
remove any threads or
hair caught around the
brushes. Rinse under
water to remove debris.
Line up spindle and tabs on
side of spin scrub cover into
carpet washer, push rmly
until it clicks into place.
Taking care of your machine
Removing and cleaning the brushbar
Using a crosshead
screwdriver, undo the 2
screws and remove the
belt guard.
Pull and slide the right side
brushes together with the
brushbar. Remove the side
cap from the brushbar and
unloop the brushbar from
the belt.
Using a crosshead screwdriver remove the 4 screws
on the side brushes and the top and bottom screws
from each of the rug guards (metal pins) to get access
to the brushbar.
Using a pair of scissors,
remove any threads or hair
caught around the brushes.
Rinse under water to
remove debris.
To ret, loop the brushbar
through the belt and onto
the belt grip.
Pull and slide the left side
brushes and remove the
side cap from the brushbar.
Line up the ‘right’ side
brushes with base and slide
into place. Attach brushbar
to side brushes.
Attach the other side
of the brushbar to the side
brushes. Slide onto the side
of the base and into place.
Ret the belt guard and tighten the 2 screws. Replace and
tighten the 4 screws on the side brushes and ret the rug
guards tightening the 4 screws to secure.
Accessories
Don’t forget your solution!
Order at: www.vax.co.uk/spares-and-solutions
Platinum (1.5l)
1-9-139136
Platinum Carpet Cleaning Solution deep
cleans carpets and removes stubborn stains.
Safe to use on wool carpets - Woolsafe approved.
Ultra+ (1.5l)
1-9-137771
Ultra+ Carpet Cleaning Solution tackles stubborn spots
and stains and removes unpleasant odours too. It’s
specially formulated to leave no sticky residue, so your
carpets stay fresher for longer. Safe to use on wool
carpets - Woolsafe approved.
Ultra+ Pet (1.5l)
1-9-137770
Ultra+ Pet Carpet Cleaning Solution tackles stubborn
spots and stains and removes unpleasant pet odours too.
It’s specially formulated to leave no sticky residue, so
your carpets stay fresher for longer. Safe to use on wool
carpets - Woolsafe approved.
Ultra+ Refresh (1.5l)
1-9-137768
Ultra+ Refresh Carpet Cleaning Solution tackles stubborn
spots and stains. Its Oxy-Lift Boost Technology brings your
carpets back to life and restores carpet pile. Formulated
to leave no sticky residue, so your carpets stay fresher for
longer. Safe to use on wool carpets - Woolsafe approved.
Ultra+ Spring (1.5l)
1-9-137769
Ultra+ Spring Carpet Cleaning Solution tackles stubborn
spots and stains and, with its fresh spring fragrance,
removes unpleasant odours too. It’s specially formulated
to leave no sticky residue, so your carpets stay fresher for
longer. Safe to use on wool carpets - Woolsafe approved.
xy
lift boost
What to do if it goes wrong
IMPORTANT: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.
SolutionProblem
• Check the contents on the box to make sure the part is
There is an
accessory missing
Why won’t the carpet
washer turn on?
Why won’t the
solution/clean
water dispense?
denitely included with your washer.
• The plug may not be fully pushed into the electrical socket.
• Check if the fuse in the plug needs replacing. Always replace
with a British 13amp fuse.
• Make sure the clean water tank is tted securely.
Go to ‘using your machine’.
• Wash/Rinse dial has been set to Rinse, set dial to wash to
dispense solution.
• The clean water tank valve may be stuck, hold the clean water tank over
the sink and press the valve underneath to release.
• Squeeze the trigger on the handle to release solution and water mix.
• The water/solution tank is empty. Rell the tank.
Go to ‘Using your machine’.
Why won’t the
carpet washer
pick up?
Why won’t the
brushes spin?
• The oat in the dirty water tank may have been activated.
Empty the dirty water tank wait for the oat to settle before re-starting
your carpet washer.
• Check the SpinScrub and brushbar for blockages and clear.
• The dirty water tank may not be tted correctly, also make sure the lid
is pushed down securely.
• Check the nozzle for blockages and clear.
• Check the nozzle is correctly tted. Go to ‘Taking care of your machine’.
• Check the lter screen located in the dirty water tank for dirt and debris.
Go to 'Emptying and cleaning the dirty water tank'.
• The brushes will only spin when the carpet washer is reclined.
• Check the SpinScrub and brushbar for blockages and clear.
Go to 'Removing and cleaning the brushbar / SpinScrub brushes'.
• Check for damage to the brushbar and the spindle on the back of the
SpinScrub brush.
Getting in touch
†
Registration required. Terms and conditions apply, see vax.co.uk for details.
GET IN TOUCH
info@vax.co.uk vax.co.uk
EU Statement of Compliance: Manufacturer/EU importer: Vax Limited, hereby on our own responsibility, declare that the
ECB1SPV1 is manufactured in compliance with the following Directives: Safety: 2014/35/EU Low Voltage Directive.
EMC: 2014/30/EU Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
© 2017 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.
Vax Ltd, Pointon Way, Stonebridge Cross Business Park, Hampton Lovett, Droitwich, WR9 OLW, UK
Loading...