Vax ONEPWR Glide CLHF-GLKS Cordless Hard Floor Cleaner User guide

1

USER GUIDE

CLHF-GLKS
CLHF-GLBS

SAFETY GUIDE 2

SAFETY GUIDE

support.vax.co.uk

This machine is intended for
household use only and NOT for
commercial or industrial use.

PLEASE KEEP INSTRUCTIONS FOR
FURTHER USE AND USE ONLY AS
INSTRUCTED IN THIS GUIDE.

DON’TS

• Don’t leave the charger plugged in
when unattended.

• Don’t use the machine if it is faulty
or has been dropped, damaged or
left outdoors.

• Don’t use the machine to pick up any
flammable or combustible materials
(lighter fluid, petrol, kerosene etc.)
or use the machine in an area with
explosive vapours or liquid.

• Don’t use the machine to pick up hot
coals, cigarette butts, matches or
smoking hot burning items or use in
an area where there may be harmful
fluids (chlorine, bleach and ammonia
drain cleaner).

• Don’t handle the charger, battery or
use the machine with wet hands.

• Don’t unplug the charger by pulling
on the power cord.

• Don’t use the charger if the charger
cord or plug is damaged.

• Don’t attempt to remove blockages
with sharp objects as this may cause
damage to the machine.

• Don’t use the machine with the
incorrect battery or charger as this
may result in damage or injury to the
user. The correct battery charger
information is listed on the battery
pack ratings label.

• Don’t charge the battery outdoors, or
leave the charger connected to the
mains when not in use.

• Don’t use this machine with a
damaged battery. If the battery is
damaged contact us on: 08000

927737.

• Don’t carry the machine while it’s
switched on.

DO’S

• Only VAX ONEPWR batteries
(BV15020/BV15030/BV25040) and
charger (BV05100UK) should be
used with this machine.

• Only VAX ONEPWR recommended
charger, batteries, tools and
accessories should be used with this
machine.

• Refer to the floor manufacturer’s
care recommendations before use.
Test your flooring - run the machine
over a small hidden area, if no
damage or discolouration occurs
continue cleaning. Not suitable for
use on water sensitive flooring.

• Always remove the battery from the
machine before carrying out any
maintenance or if storing unused for
a long period of time.

• Keep all openings clear and free
from debris as this may affect the
airflow/suction.

• Turn off all controls on the machine
before disconnecting or connecting
the battery.

• Always protect the charger power
cord from heated surfaces or near
open flames.

SAFETY GUIDE 3

support.vax.co.uk

• The machine can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the machine
in a safe way and understand the
hazards involved. Children shall not
play with the machine. Cleaning and
user maintenance shall not be made
by children without supervision.

• Only use the machine indoors and
keep the area you’re cleaning well lit.

• Keep fingers, hair and loose clothing
away from moving parts and
openings whilst using the machine.

• Store the machine in a cool, dry
area. Before storing ensure all
water/solution tanks and filters are
thoroughly clean and dry.

• Use only CE approved 13amp
extension cords, non-approved
extension cords may overheat.
Care should be taken to arrange the
extension cord as it can be a trip
hazard.

• The clean water tank should be filled
with warm water (max 40°C) only.
Filling the clean water tank with
hot or boiling water will damage
the machine and invalidate the
guarantee. Always use the machine
with all water/solution tanks and
filters in place.

• Only VAX recommended solution
should be used with the machine.
Using other solutions may invalidate
the guarantee.

• Always use the machine in an
upright position. To prevent motor
damage from dirty water, never hold
the machine upside down or on its
side. Always stand the machine on a
stable, level surface.

• Always check the brushroll is free
from damage, dirt and debris before
using.

BATTERY SAFETY PRECAUTIONS

• Replace battery with VAX
ONEPWR battery only. Use of
another battery may present a risk
of fire or explosion.

• Do not attempt to disassemble the
battery, remove any component
projecting from the battery terminals
and do not dispose of in a fire.
The battery and charger have no
user serviceable parts. Fire or injury
may result.

• Prior to disposal, protect exposed
terminals with heavy insulating tape
to prevent shorting. The battery is to
be disposed of safely at your local
battery recycling centre.

• When the battery pack is not in
use, keep it away from other metal
objects that can make a connection
from one terminal to another.
Shorting the battery terminals
together may cause burns or a fire.

• In case of battery leakages, avoid
any contact with skin and contact us
on: 08000 927737.

WARRANTY & TECHNICAL

WARRANTY

If a VAX ONEPWR machine is used
in the way it is intended and it breaks
down within the guarantee period, it’s
our responsibility to repair or replace it.
Here’s what isn’t covered:

• Normal wear and tear of consumable
items, for example: belts, filters,
brushrolls, fuses etc.

• Batteries which have become faulty
as a result of improper handling.

• Batteries which have a reduced
service life as a result of normal wear.

• Accidental damage

- Damage as a result of use not in
accordance with the product
user guide.

- Damage caused by not carrying out
regular maintenance.

- Damage to the charger cable.

- Blockages caused by misuse.

support.vax.co.uk

• Faults caused by:

- Negligent use, misuse, neglect or
careless operation of the machine.

- Use of the machine cleaner which
is not in accordance with the
user guide.

- Use of a VAX ONEPWR machine
for anything other than normal
domestic household purposes
in the country in which it was
purchased.

- Use of parts, accessories and
consumables, which are not
genuine VAX components.

- Faulty installation or repairs –
unless carried out by a qualified
electrician or engineer.

4

TECHNICAL

EU Statement of Compliance: Manufacturer/EU importer: VAX Limited, hereby on
our own responsibility, declare that the VAX ONEPWR Glide is manufactured in
compliance with the following Directives:
Safety: 2014/35/EU Low Voltage Directive.
EMC: 2014/30/EU Electromagnetic Compatibility Directive.

Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.

© 2019 VAX Limited. All rights reserved. The VAX trade mark and VAX lozenge
are the property of Techtronic Floor Care Technology Ltd and are registered in the
EU and may be pending or registered in other countries.

VAX Ltd, Artillery House, Heritage Way, Droitwich, WR9 8YB, UK.

GETTING TO KNOW YOUR MACHINE

1

1

2

3

4

5

14

Trigger

2

Handle

3

Power ON/OFF

4

Mode selector

5

Main unit

6

Dirty water tank release latch

7

Filter (hidden)

8

Separator

9

Dirty water tank

10

Brushroll cover release button

11

Brushroll cover

12

Brushroll

13

Rinse/Storage tray

14

Battery dock

15

Battery cover

16

Water/Solution tank

17

ONEPWR Battery*

18

ONEPWR Charger*

19

250ml Multi-floor Solution

support.vax.co.uk

5

6

7

8

9

10

15

16

17 18

19

TECHNICAL SPECIFICATION

11

12

13

VAX ONEPWR Glide

Weight (without battery pack) 4.9kg
Water/Solution Tank capacity 0.64L
Dirty Water Tank capacity 0.29L

Runtime and charge time dependent on battery pack used.
*Included with model CLHF-GLKS only.

Subject to technical change without notice. Images are illustrative only.

GETTING STARTED

support.vax.co.uk

CHARGING THE BATTERY

THIS MACHINE IS ONLY TO BE USED WITH VAX ONEPWR BATTERIES AND CHARGER.
PLEASE READ THE SAFETY GUIDE BEFORE USE.

NOTE: Before first use, ensure the battery is fully charged. Failure to fully charge the battery
before first use may result in poor battery performance. The life expectancy of the battery will vary
depending on the usage of the machine.

6

Slide the battery down on to the charger
until it clicks into place.

The charger light will flash white to
show when the battery is charging.
The light on the charger will stop
flashing and go off when the battery
is fully charged.

Once fully charged, slide the battery off
the charger to remove.

To check the battery charge
level press the battery symbol.

GETTING STARTED

IMPORTANT:

• Test the machine over a small hidden area of your flooring before use. If no damage occurs continue
cleaning.

• When using the machine, basic safety precautions should always be observed. Take care not to
oversaturate flooring. Always finish on a dry stroke (no trigger pressed).

• For heavily soiled areas, it may be necessary to repeat the cleaning process.

• Only use VAX ONEPWR Multi-floor solution. Using other solutions may cause excess foaming and
will invalidate your guarantee.

• The water/solution tank should only be filled with warm water (max 40⁰C). Filling the water/
solution tank with hot/boiling water will damage your washer and invalidate the guarantee.

• Empty and rinse out water/solution tank and dirty water tank and leave to air dry before storage.
Do not leave solution stored in the tanks between uses.

• For prolonged storage the brushroll should be removed, cleaned and stored in the rinse/storage tray.

support.vax.co.uk

ASSEMBLY

7

Push the handle into the main body
until it clicks into place.

Close the battery cover.

Pull to open the battery cover.

To remove the battery press both the
buttons to release.

Holding the cover open, slide the battery
into the machine until it clicks into place.

GETTING STARTED

support.vax.co.uk

FILLING THE WATER / SOLUTION TANK

IMPORTANT: Do not leave solution stored in the tanks between uses.

NOTE: When unpacking the machine, the water/solution tank cap will be attached to the side of the
tank. Before first use, and after water/solution has been added, ensure that the cap is screwed onto
the water/solution tank before refitting onto the machine.

SOLUTION

LARGE AREA

WATER

SOLUTION

WATER

SMALL AREA

8

Lift to remove the water/solution tank
from the back of the machine.

Unscrew the cap and fill to the desired
level using the markers on the tank.

Replace the cap and push the tank
down on to the machine until it clicks
into place.

GETTING STARTED

support.vax.co.uk

OPERATION

IMPORTANT: Your dirty water tank is fitted with a float. When the dirty water tank is full, or the
floorhead is not in contact with the floor, the float will shut off the suction on the machine. You will
be able to hear if this has happened as the motor noise on the machine will increase. Once the float
is activated, check if the dirty water tank is full and empty if necessary. If the dirty water tank is not
full, continue to check for blockages.

9

Place your foot on the base and pull the
handle backwards to recline.

Press the trigger on the handle to
release water and solution. Release the
trigger to recover the water and solution.

Press the on/off button to switch the
machine on. The machine will always
start in High Mode.

For best results apply water/solution
on the forward stroke and release the
trigger on the backward stroke to pick up
water/solution. For a dryer finish, follow
with an additional dry stoke without the
trigger pressed.

For an improved runtime, press the
mode selector button to switch to
Eco Mode.

For a more intense clean, press the
mode selector button to switch to
High Mode.

During use, regularly empty the dirty
water tank ensuring the water does not
exceed the max fill line marked on the
side of the tank.

CLEANING & MAINTENANCE

support.vax.co.uk

ALWAYS SWITCH OFF THE MACHINE AND REMOVE THE BATTERY BEFORE CARRYING OUT ANY
MAINTENANCE OR TROUBLESHOOTING.

EMPTYING THE DIRTY WATER TANK

IMPORTANT: Empty and rinse out the water/solution tank and dirty water tank and leave to air dry
before refitting.

10

Press down the dirty water tank release
button and pull the tank to remove.

Twist the separator clockwise to release
from the lid.

Hold the top of the dirty water tank lid and pull upwards to remove.

40°C
MAX

Empty the dirty water over a sink. Rinse
the tank and separator under water
(max 40°C) to remove dirt/debris.

To refit, line up the separator tab with the
lid tab and twist anticlockwise to lock.

To re-fit, tilt the dirty water tank and line the front of the
tank up onto machine. Push back until it clicks into place.

CLEANING & MAINTENANCE

support.vax.co.uk

CLEANING THE FILTER

IMPORTANT: After every use wash the filter with warm water (40°C max) and leave for 24 hours or
until fully dry before refitting onto the machine. For best cleaning results filters should be replaced
every 6 months (depending on the level of use). Ensure all filters are in place before using the machine.

11

40°C
MAX

Pull the tab on the bottom of the filter
to remove.

Wash the lter under running water (40°C max).
Leave for at least 24hrs or until fully dry before retting.

CLEANING THE SEPARATOR

Hold the top of the dirty water tank lid and pull upwards to remove.

24hr

Twist the separator clockwise to release
from the lid.

40°C
MAX

Wash the separator mesh under running
water (40˚ max) to remove any dirt
and debris.

To refit, line up the separator tab with the
lid tab and twist anticlockwise to lock.

CLEANING & MAINTENANCE

support.vax.co.uk

MACHINE RINSE AND BRUSHROLL QUICK CLEAN

IMPORTANT: We recommend rinsing the machine and quick cleaning the brushroll after every use.

SOLUTION

LARGE AREA

WATER

SOLUTION

WATER

SMALL AREA

12

Fill the tank up with warm water
(40˚ max) and replace the cap.

Switch the machine on. Press the trigger to release water onto

Refit the tank into the machine.

Recline the machine so that the
brushes rotate.

Place the machine upright in the rinse/
storage tray.

the brushroll. Release the trigger at
regular intervals to remove the brushroll
dirt and debris. Repeat the process until
the brushroll is clear and clean.

CLEANING & MAINTENANCE

support.vax.co.uk

REMOVING AND ADVANCED CLEANING OF THE BRUSHROLL

IMPORTANT: Make sure both the brushroll and brushroll cover are fitted correctly. If fitted incorrectly
this may cause poor water pick up. For best cleaning results, advanced cleaning of the brushroll
should be done every 5-6 uses. For prolonged storage, the brushroll should be removed, cleaned and
stored in the rinse/storage tray.

CAUTION: If the brushroll has been obstructed, the brushroll motor protection sensor may have
been activated. The brushroll will stop, the light on the handle will flash white and the machine may
switch off. To reset, remove the brushroll and clear any obstruction. Wait 1 minute before refitting the
brushroll, switch the machine on and recline.

13

Press the brushroll cover button and
pull to open the cover.

40°C
MAX

Rinse the brushroll in water (40˚ max)
and allow to dry before refitting.

Unhook the brushroll cover and
remove.

The brushroll can be dried and stored
in the rinse/storage tray.

To remove the brushroll, pull the tab
on the end and remove from the
brushroll housing.

Clean the brushroll housing and
brushroll cover of any dirt and debris.

SAFETY GUIDE 14

support.vax.co.uk

REFITTING THE BRUSHROLL

To refit the brushroll, slide the right
side into the machine and then push
the left side in until it clicks.

Hook the brushroll cover onto the tabs on the base and close until it
clicks into place.

CHECKING FOR BLOCKAGES

Check for blockages and use a blunt
object to remove the blockage.

TROUBLESHOOTING

THERE IS AN ACCESSORY MISSING

Check the contents on the back of the box.

WHY DOES THE MACHINE HAVE NO POWER?

• The battery is not fitted correctly. See ASSEMBLY page 7.

• The battery has no charge. See CHARGING THE BATTERY page 6.

• The motor thermostat may have tripped. Empty the dirt water tank and check for blockages.

Clean the filter and allow the machine to cool for approximately 1 hour. If you have washed the filter
and separator, wait 24 hours to fully dry before placing back on the machine. See CLEANING THE
FILTER AND SEPARATOR page 11.

• The brushroll motor sensor has been activated. To reset remove the brushroll and clear any
obstruction. Wait 1 minute before refitting the brushroll. Switch the machine on and recline.
See REMOVING AND ADVANCED CLEANING OF THE BRUSHROLL page 13.

WHY WON’T THE MACHINE PICK UP?

• The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for
the float to settle before re-starting the machine. See EMPTYING THE DIRTY WATER TANK page 10.

• The brushroll cover may not be correctly fitted. See REMOVING AND ADVANCED CLEANING OF
THE BRUSHROLL page 13.

• The dirty water tank may not be assembled correctly or the lid may not be pushed down securely.
See EMPTYING THE DIRTY WATER TANK page 10.

• Check for blockages and clear. See CHECKING FOR BLOCKAGES page 14 and MACHINE RINSE
AND BRUSHROLL QUICK CLEAN page 12.

• Check the filter located on the dirty water tank lid for dirt and debris. The filter should be washed
after every use and replaced every 6 months. See CLEANING THE FILTER page 11.

• Check the separator for dirt and debris and clean if necessary. SEE CLEANING THE SEPARATOR
page 11.

WHY WON’T THE WATER/SOLUTION DISPENSE?

• Squeeze the trigger on the handle to release water and solution.

• Make sure the water/solution tank is fitted securely. See FILLING THE WATER/SOLUTION TANK

page 8.

• The water/solution tank valve may be stuck. Hold the water/solution tank over the sink and press the
valve underneath to release.

• The water/solution tank is empty. Refill the tank. See FILLING THE WATER/SOLUTION TANK page 8.

WHY WON’T THE BRUSHROLL TURN?

• The machine is not reclined. Place your foot on the base and pull the handle backwards to recline.
See OPERATION page 9.

• The brushroll may be obstructed or may not be correctly fitted. See REMOVING AND ADVANCED
CLEANING OF THE BRUSHROLL page 13.

WHY IS THERE A FLASHING WHITE LIGHT ON THE HANDLE?

• The brushroll motor sensor has been activated. To reset remove the brushroll and clear any
obstruction. Wait 1 minute before refitting the brushroll. Switch the machine on and recline. See
OPERATION page 9 and REMOVING AND ADVANCED CLEANING OF THE BRUSHROLL page 13.

support.vax.co.uk

15