Page 1
USER GUIDE
CLSV-B4KS
CLSV-B4BS
Page 2
SAFETY GUIDE 2
SAFETY GUIDE
support.vax.co.uk
This machine is intended for
household use only and NOT for
commercial or industrial use.
PLEASE KEEP INSTRUCTIONS FOR
FURTHER USE AND USE ONLY AS
INSTRUCTED IN THIS GUIDE.
DON’TS
• Don’t leave the charger plugged in
when unattended.
• Don’t use the machine if it is faulty
or has been dropped, damaged or
left outdoors.
• Don’t use the machine to pick up any
flammable or combustible materials
(lighter fluid, petrol, kerosene etc.)
or use the machine in an area with
explosive vapours or liquid.
• Don’t use the machine to pick up hot
coals, cigarette butts, matches or
smoking hot burning items or use in
an area where there may be harmful
fluids (chlorine, bleach and ammonia
drain cleaner).
• Don’t handle the charger, battery or
use the machine with wet hands.
• Don’t unplug the charger by pulling
on the power cord.
• The power cord cannot be replaced.
If the cord is damaged the charger
should be scrapped.
• Don’t attempt to remove blockages
with sharp objects as this may cause
damage to the machine.
• Don’t use the machine with the
incorrect battery or charger as this
may result in damage or injury to the
user. The correct battery charger
information is listed on the battery
pack ratings label.
• Don’t charge the battery outdoors, or
leave the charger con nected to the
mains when not in use.
• Don’t use the machine with a
damaged battery. If the battery is
damaged contact us on: 08000
927737.
• Don’ t use on a surf ace that is
damaged, uneven or inc or rectly fitted.
• The brushbar in the powered
floorhead constantly rotates
when switched on. Never use the
powered floorhead on one spot for
an extended period of time as the
brushbar may damage the floor
surface.
DO’S
• Only VAX ONEPWR batteries
(BV15020/BV15030/BV25040) and
charger (BV05100UK) should be
used with this machine.
• Always stand the charger on a
stable, level surface, uncovered and
away from any heat source.
• Only VAX ONEPWR recommended
tools and accessories should be
used with this machine.
• Always remove the battery from the
machine before carrying out any
maintenance or if storing unused for
a long period of time.
• Keep all openings clear, free from
debris and don’t overfill the dirt
container as this may affect the
airflow/suction.
• Turn off all controls on the machine
before disconnecting or connecting
the battery.
Page 3
SAFETY GUIDE 3
support.vax.co.uk
• Only use the machine indoors on dry
surfaces and keep the area you’re
cleaning well lit.
• This machine is not intended to be
used or cleaned by persons with
reduced physical, sensory or mental
capabilities, or lack of experience or
knowledge, unless they have been
given instructions concerning the
safe use of the machine by a person
legally responsible for their safety.
They should be supervised whilst
using the machine. Children shall not
use, clean or play with this machine,
which when not in use should be
secured out of their reach.
• Keep fingers, hair and loose clothing
away from moving parts and
openings whilst using the machine.
• Store the machine in a cool, dry
area. Keep the machine away from
rain and moisture.
• Use only CE approved 13amp
extension cords, non-approved
extension cords may overheat.
Care should be taken to arrange the
extension cord as it can be a trip
hazard.
• Take extra care when using the
machine on the stairs.
• Always turn the power ed floorhead
brushbar off when cleaning hard
floors. To prevent any damage being
sustained, test on an inconspicuous
area of the flooring first.
• Always make sure the separator
and filter are fitted correctly before
using your machine and only use the
machine with the filter and separator
in place.
• Always check the powered floorhead
and accessories are free from
damage, dirt and debris before
using.
• This machine does not stay upright
without constant support. Between
uses, lie flat on the floor in a suitable
location so that it does not become a
trip hazard or can be stepped on.
BATTERY SAFETY PRECAUTIONS
• Replace the battery with a VAX
ONEPWR battery only. Use of
another battery may present a risk
of fire or explosion.
• Do not attempt to disassemble the
battery, remove any component
projecting from the battery terminals
and do not dispose of in a fire.
The battery and charger have no
user serviceable parts. Fire or injury
may result.
• Prior to disposal, protect exposed
terminals with heavy insulating tape
to prevent shorting. The battery is to
be disposed of safely at your local
battery recycling centre.
• When the battery pack is not in
use, keep it away from other metal
objects that can make a connection
from one terminal to another.
Shorting the battery terminals
together may cause burns or a fire.
• In case of battery leakages, avoid
any contact with skin and contact us
on: 08000 927737.
Page 4
WARRANTY & TECHNICAL
WARRANTY
If a VAX ONEPWR mach i ne is used
in the wa y i t is int e nd ed and it break s
down wit h in the guara ntee peri od, it’s
our respo nsibility to repa ir or replace it.
Here’ s wh at isn ’t cov e red:
• Normal wear a nd tear of c on s um ab le
item s, for exampl e : be lts, fil ters,
brushbars, fuses etc.
• Batter ies which ha ve become faulty
as a resu lt of impr ope r h andling.
• Batter ies which ha ve a reduced
service l ife as a r e su lt of normal wear.
• Accidental damage
- Damag e a s a result o f u se not in
accor dance with the pr oduct
user guide.
- Damag e c au sed b y n ot carrying out
regular maint enance.
- Damag e to the char ger cable .
- Blockages caused by m isuse.
support.vax.co.uk
• Fault s caused by :
- Negligent use, misuse, neglect or
careless operation of the ma c h ine.
- Use of the machine cleaner which
is not i n accord an ce with the
user guide.
- Use of a VAX ONEPWR machine
for anyth ing other t h an nor m a l
domesti c hou se hold purposes
in the country in whic h i t was
purchased.
- Use of parts, a ccessorie s and
consumab les, which are not
genuine VAX components.
- Faul ty i n s tallat ion or repai rs –
unless car r ied out by a qualified
electrician or engineer .
4
TECHNICAL
EU Statement of Compliance: Manufacturer/EU importer: VAX Limited, hereby on
our own responsibility, declare that the V AX ONEPWR Blade 4 is manufactured in
compliance with the following Directives:
Safety: 2014/35/EU Low Voltage Directive.
EMC: 2014/30/EU Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.
V AX is a t rade mark of Techtronic Cordless GP.
© 20 20 Techtroni c C ordless GP. Al l r ights reserved.
VAX Ltd, Artillery House, Heritage Way, Droitwich, WR9 8YB, UK.
Page 5
GETTING TO KNOW YOUR MACHINE
6
1
2
3
4
5
10
7
8
9
13
14
support.vax.co.uk
1
Carry handle
2
Dirt container
3
Filter cover and filter
4
Dirt container release latch
5
Dirt r elease button
6
P ower ON/OFF
7
Brushbar ON/OFF
8
Boost ON/OFF
9
Battery level indicator light
10
Reach wand
11
P owered floorhead
12
Brushbar
13
Battery dock
14
Filter cover r elease tab
(hidden)
15
ONEPWR Battery*
16
ONEPWR Charger*
17
Cr evice tool
18
Dusting brush
19
Cr e vice tool storage caddy
20
Wall mount
screws and wall plugs
5
15 16
19 2017 18
TECHNICAL SPECIFICATION
VAX ONEPWR Blade 4
Weight (without battery pack) 2.8kg
11
12
Dirt bin capacity 0.6L
Runtime and charge time dependent on bat tery pack
and power mode used.
*Included with model CLSV-B4KS only.
Subject to technical change without notice. Images are illustr ativ e only .
Page 6
GETTING STARTED
The dusting brush can be fitted onto the
wall bracket.
Fully assemble the machine and firmly
press the machine into the wall bracket
to secure. Always ensure the machine is
securely locked into place.
ASSEMBLY
support.vax.co.uk
6
To as semble the dirt container, line up the arrow on the dirt
container connection with the arrow on the handle. Push the
dirt container onto the handle until it clicks into place.
ATTACHING THE WALL MOUNT
Without the handheld attached to the
reach wand and power ed floorhead,
push the wall bracket onto the top and
back of the reach wand.
Choose a location for the machine to be stored, preferably near to a mains supply
although not directly abov e or below a mains socket. Stand the machine power ed
floorhead and wand against the wall, ensuring the power ed floorhead is flat on
the floor.
Attach the handheld to the reach wand until it clicks into place.
Attach the r each wand to the powered floorhead until it clicks
into place. Push the tool caddy onto the reach wand and slot the
crevice tool into place.
Holding the wall bracket securely against
the wall, make a small mark for each
screw. Secure the wall bracket to the
wall using the wall plugs and screws.
Page 7
GETTING STARTED
support.vax.co.uk
CHARGING THE BATTERY
THIS MACHINE IS ONLY TO BE USED WITH VAX ONEPWR BATTERIES AND CHARGER.
PLEASE READ THE SAFETY GUIDE BEFORE USE.
NOTE: Before first use, ensure the battery is fully charged. Failure to fully charge the battery
before first use may result in poor battery performance. The life expectancy of the battery will vary
depending on the usage of the machine.
7
Slide the battery down on to the charger. The charger light will flash white to
show when the battery is charging.
The light on the charger will stop
flashing and go off when the battery
is fully charged.
Once fully charged, slide the battery off
the charger to remove.
To check the battery charge
level press the battery symbol.
OPERATION
WARNING: The brushbar in the powered floorhead constantly rotates when switched on. Never use
the powered floorhead on one spot for an extended period of time as the brushbar may damage the
floor surface. Always turn the powered floorhead brushbar off when cleaning hard floors. To prevent
any damage being sustained, test on an inconspicuous area of the flooring first.
Slide the battery into the handheld until
it clicks into place.
Place your foot on the powered floorhead.
Pull the handle backwards to r ecline.
To remove the battery press both the
buttons to release.
Page 8
GETTING STARTED
OPERATION
support.vax.co.uk
8
Press the on/ of f button to switch the
machine on.
Press the brushbar on/off button to
switch the brushbar on.
Press the boost button on to increase
the suction for particularly dirty areas.
NOTE: The powered floorhead brushbar should be ON for carpets and OFF for hard floors.
Constant use of the boost mode and brushbar will reduce the battery runtime.
When the machine is in use the battery
level indicator lights will illuminate
indicating how much charge is
remaining. When less than 20% char ge
is remaining the bottom light will flash
red indicating the battery is run ning low
and charging is requir ed.
All of the accessories, including the
powered floorhead can be attached
directly onto the handheld or the reach
wand. The crevice tool and dusting
brush can be used for hard to reach
places and at different heights for above
floor cleaning.
CAUTION: If the brushbar in the powered floorhead has been
obstructed, the brushbar motor protection sensor may have been
activated. The brushbar will stop, the light on the powered floorhead
will illuminate red and the machine may switch off. To reset remove
the powered floorhead from the reach wand/handheld and clear any
obstruction. Wait 1 minute before refitting the powered floorhead tool,
switch the machine on and press the brushbar ON/OFF button.
Page 9
CLEANING & MAINTENANCE
support.vax.co.uk
REMOVING AND REFITTING THE DIRT CONTAINER
WARNING: Always remove the battery before carrying out any maintenance or troubleshooting.
1
2
9
1. Squeeze the latch on the dirt
container to release.
2. Tilt and lift to remov e from the
handheld.
To refit, line up the dirt container
connection with the handheld handle.
Push the dirt container back onto the
handle until it clicks into place.
When correctly fitted all 3 connection
points will be aligned and will sit flush.
EMPTYING THE DIRT CONTAINER
CAUTION: Don’t over fill the dirt container to avoid blocking the air flow through the machine.
For best cleaning results, empty the dirt container after every use. Filters should be tapped over a
bin every 4-6 uses to remove dirt and debris and washed every 3 months. Filters should be replaced
every 6-9 months depending on the level of use.
1
2
1. Squeeze the latch on the dirt
container to release.
2. Tilt and lift to remov e from the
handheld.
Hold the dirt container over a bin and
press the dirt r elease button to allow dirt
and debris to fall out.
To close, push the dirt release door until
it clicks into place.
Page 10
CLEANING & MAINTENANCE
CLEANING THE FILTER AND SEPARATOR
support.vax.co.uk
10
Push the tab on the lid of the dirt container and lift the cover to access the filter.
Tap the separator over a bin to remove
dirt and debris and wipe over the metal
shroud with a dry cloth.
Pull the tab on the filter to remove from
the separator.
CAUTION: Ensure both
the filter and separator are
refitted before use.
40°C
MAX
24hr
Lift the filter and separator from the
dirt container.
Tap the filter against the bin to remove
any dirt and debris.
Wash the filter under running water
(40°C max). Leave for at least 24hr s or
until fully dry befor e replacing.
Page 11
CLEANING & MAINTENANCE
support.vax.co.uk
CLEANING AND REPLACING THE POWERED FLOORHEAD BRUSHBAR
11
remove the floorhead from the machine.
Pull the brushbar out from the brushbar
housing.
Using a coin, push and turn the brushbar lock anticlockwise to release the brushbar.Press the floorhead r elease button to
To remove any thr eads or hair, slide
the blade of a pair of scissors into the
groove on the brushbar and cut along
the groove.
Clear any dirt/ debris from the end caps
and inside the housing of the powered
floorhead.
Refit the brushbar into the floorhead. Align the arrow on the brushbar cover so it
points north, firmly push and twist clockwise to lock.
Page 12
CLEANING & MAINTENANCE
CHECKING FOR BLOCKAGES
support.vax.co.uk
12
Press the handheld r elease button and
remove the reach wand. Check and clear
any dirt and debris from the handheld
connection point.
Press the dirt container release button
and remove the dirt container. Check
and clear any dirt and debris from
behind the dirt container flap.
To test for a blockage in the reach wand,
drop a small ball of paper into the wand.
The paper will drop thr ough if the wand
is clear. Use a broom handle or similar
blunt object to remov e any blockage.
Check the powered floorhead for any
blockages and use a blunt object to
remove the blockage.
Page 13
TROUBLESHOOTING
THERE IS AN ACCESSORY MISSING
Check the contents on the back of the box.
WHY DOES THE MACHINE HAVE NO POWER?
• The battery is not fitted cor rectly. See OPERATION page 7.
• The battery has no charge. See CHAR GING THE BATTERY page 7.
• The motor thermostat may have tripped. Empty the dirt container and check for blockages.
Clean the filters and allow the machine to cool for approximately 1 hour. If you have washed
the filters, wait 24 hours to fully dry before placing back on the machine.
See CLEANING THE FIL TER AND SEPARATOR page 10.
• The brushbar motor sensor has been activated. To reset remove the po w ered floorhead from
the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting the powered
floorhead, switch the machine on and pr ess the brushbar ON/OF F button. See OPERATION
page 8.
WHY WON’T THE MACHINE PICK UP?
• The dirt container may not be cor rectly fitted. See REMOVING AND REFITTING THE DIRT
CONTAINER page 9 .
• The dirt container may be blocked. Check the dirt c ontainer and handheld inlet for blockages.
See EMPTYING THE DIRT CONTAINER page 9.
• The filters may be clogged. See CLEANING THE FILTER AND SEPARATOR page 10.
• There maybe a blockage. See CHECKING FOR BLOCKA GE S page 12.
• The brushbar on the power ed floorhead has not been activated. See O P ERATION page 8.
• The powered floorhead may be block ed. See CLEANING AND REPLACING THE P O WERED
HEAD BRUSHBAR page 11.
• The machine, powered floorhead and reach wand may not be correctly fit ted.
See ASSEMBLY page 6.
support.vax.co.uk
13
WHY IS THERE A RED LIGHT?
• Battery charge is running lo w (<20%). See CHARGING THE BA TTERY page 8.
WHY IS THERE A RED LIGHT ON THE POWERED FLOORHEAD?
• The powered floorhead brushbar has been obstructed. See CLEANING AND REPLACING THE
POWERED FLO ORHEAD BRUSHBAR page 11.
WHY WON’T THE BRUSHBAR TURN?
• The brushbar on the power ed floorhead has not been activated. Go to O P ERATION page 8.
• The tool/brushbar may be obstructed. See CLEANING AND REPLACING THE POWERED
HEAD BRUSHBAR page 11.
• The machine, powered floorhead and reach wand may not be correctly fit ted. See AS SEMBLY
page 6.
Loading...