www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
R
e
tain f
or future reference.
Vax careline
0870 6061248
instruction manual
Bagless upright
Vax model number:
VZL-6017 Series
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 1
1. Diagram
www.vax.co.uk
2
parts overview
3
1
2
15
2
3
14
13
12
11
10
16
17
18
19
20
21
22
4
5
6
7
8
VZL-6017
Fig.1/1
1
Soft Touch handle grip
2 On/Off switch
3 Hose
4 Dirt cup release button
5 Dirt cup assembly
6
Hose handle
7 Cord reel window/ Exhaust vent
8 Headlight
9
No
zzle c
on
tr
ol knob: turn knob
t
o c
orr
ect se
tting for height of
carpe
t being cleaned
10
Furniture guard: helps prevent
cleaner from marking furniture
11
Brush bar shut-off pedal
12 Brush bar shut-off indicator
13 Exhaust filter access
14 Combination tool
15 TurboTool
16
Cr
e
vice t
ool
17 Hose/tool holder
18
Extension wands
19 Cord reel
20 Soft Touch™ wheels
21 Handle release pedal: step on
lever to lower handle to operating
or lo
w positions
22 Cord rewind button: press button
t
o r
e
wind c
or
d for storage. Hold
plug until cord is rewound
23 Hard Floor Brush
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 2
3
Vax Careline 0870 606 1248
safety information
2. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.
4. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the appliance.
5. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.
6. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified
person for examination, repair or adjustment.
7. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the
cord around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.
8. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
9. Do not put any objects into openings. Do not use
with an
y openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
10.
K
eep hair
, loose clothing, fingers and all parts of the
body away from openings and moving parts.
11. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
12. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
pr
esence o
f e
xplosiv
e liquids or v
apours.
13.
Do no
t vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).
14. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.
15. Do not use without the filters in place.
16. Take extra care when vacuuming on stairs.
17. Keep vacuuming area well lit.
18. Store the vacuum cleaner indoors in a cool, dry area.
19. Turn off the on/off switch before unplugging the
vacuum cleaner.
20. Use only CE-approved 13 amp extension cords.
Non-approved extension cords may overheat. Care
should be taken to arrange the cord so that the
cord cannot be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.
CAUTION: The vacuum cleaner is a very powerful
unit. Before plugging the cord into the electrical
outlet, make sure the switch is in the ‘off’ position. Hold
the vacuum cleaner firmly when starting and in use.
IMPORTANT: If the inlet, hose or extension tube is
blocked, switch off the vacuum cleaner and
remove the blockage(s) before re-starting the vacuum
cleaner.
IMPORTANT: Cleaning filters regularly improves
vacuum performance. Make sure all filters are
replaced back into the vacuum cleaner before using. This
vacuum cleaner is intended for household use only and
not for commercial or industrial use.
PLEASE KEEP THESE INSTRUCTIONS FOR
FURTHER USE.
!!!
!
Motor Thermostat
IMPORTANT: The motor is equipped with a
thermal cut-out. If for any reason, the vacuum
cleaner should over-heat, the thermostat will
automatically turn the unit off. Should this occur,
unplug the v
acuum cleaner from the electrical outlet
and turn off the switch. Remove the dirt container
and empty. Clean the filters. Allow the cleaner to cool
f
or appr
o
xima
tely one (1) hour. To re-start, plug into
an electrical outle
t and swit
ch back on.
!
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 3
www.vax.co.uk
4
how to assemble
3. How to assemble
Attach Handle
Using a Phillips screwdriver, remove (2) screws from the
top of the upper housing assembly (Fig.3/1).
Insert handle section (A) into upper housing assembly.
Push down firmly until you hear a click (Fig.3/2).
Fasten (2) screws on either side of handle base (Fig.3/3).
P
osition Tools
Place smaller diameter end of wand (A) into bottom of
holder. Snap wand into clip at top. Repeat with other
wand.
Crevice tool (B) fits into one of the extension wands.
F
it combination tool (C) into storage area on side of
cleaner as shown (Fig.3/4).
Fit TurboTool (A) into recessed area on front of cleaner.
Pivot toward handle to snap in place (Fig.3/5).
Fig.3/1
Fig.3/2
Fig.3/3
Fig.3/4
Fig.3/5
A
A
A
B
C
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 4
5
Vax Careline 0870 606 1248
how to operate
4. How to operate
On/Off Switch
Plug cord into electrical outlet. To turn cleaner ON, push
ON/OFF switch once. To turn cleaner OFF, push switch
again (Fig.4/1).
Brush bar Switch
The cleaner is shipped with the brush bar in the OFF
position. To turn the brush bar ON, step on the pedal (A).
The indicator (B) will show red in the “brush bar on”
window (Fig.4/2).
Cord Rewind
Grasp the end of the plug and pull to release cord from
cord reel. After desired cord length is reached, the cord
will lock into position.
T
o return cord for storage, hold plug and press on button
(A) at top of cord reel (Fig.4/3).
NOTE: To prevent cord from whipping, hold plug until
c
or
d is r
ewound.
Transporting Cleaner
To move your cleaner from room to room, put handle
in upright position, tilt cleaner back on rear wheels and
push forward (Fig.4/4).
Handle Positions
The handle of your cleaner has three positions; upright
for storage and when using cleaning tools; operating
position for general operation on carpet and floors; low
for reaching under low furniture. Step on handle release
lever to lower handle (Fig.4/5).
Fig.4/1
Fig.4/2
Fig.4/4
Fig.4/5
Fig.4/3
A
B
A
1
2
3
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 5
www.vax.co.uk
6
how to operate / accessories
C
arpet Height Adjustment
The cleaning of carpet and rugs takes place at the nozzle
(A). When it is necessary to raise and lower the nozzle for
various carpet pile heights, turn the nozzle control knob
(B) to the desired setting (Fig.4/6).
Settings
For maximum cleaning
performance, the following
carpet height settings are
recommended (Fig.4/7):
• Lowest setting for all
types of carpet.
NOTE: If the cleaner is
difficult to push, turn knob
to the next higher setting.
• Higher settings: for very deep pile carpet, where easier
pushing effort is desired, while maintaining good
cleaning performance.
Brush bar Shut-off
The brush bar shuts off automatically for tool use, when
the cleaner is in the upright position. To manually shut
off the brush bar for cleaning hard floors, step on the
pedal (A). The indicator (B) will show red in the “brush bar
off” window. To turn the brush bar on, step on the pedal
again. The indicator will show red in the “brush bar on”
window. (Fig.4/8)
5. Accessories
Select proper tool (Fig.5/1)
A. Combination tool: use with brush for carved furniture,
table tops, books, lamps, lighting fixtures, venetian
blinds, skirting boards, shutters, and registers. Remove
brush (Fig.5/3) to clean upholstered furniture, mattresses,
clothing, and carpeted stairs.
B. TurboTool: may be used for upholstered furniture,
mattresses, clothing, automobile interiors, and carpeted
stairs.
C. Crevice tool: may be used in tight spaces, corners and
along edges in such places as upholstered furniture,
stairs and skirting boards.
D. Wands: are used to give extra length to your hose.
Use them with any of the above tools.
E. Hard floor brush (Model: VZL-6017HF only): used to
vacuum any kind of hard floor.
Attach Wand and Tools
Attach tool or wand to the hose (A).
Attach tool to wand (B) by pushing it firmly onto the
wand.
Twist wand or tool slightly to tighten or loosen the
connection (Fig.5/2).
Fig.4/8
Fig.5/1
Fig.5/2
A
A
C
D
E
B
B
Fig.4/6
Fig.4/7
A
A
B
B
HIGH LOW
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 6
7
Vax Careline 0870 606 1248
accessories
Combination Tool
Slide brush to remove. To replace brushes, align brushes,
align bottom of brush with grooves (A) on tool. Slide
brush into place (Fig.5/3).
Stair Cleaning
Use the hose and Turbo Tool for stair cleaning. Clean
from bottom to top
CAUTION: To avoid personal injury or
unnecessary wear to carpet, and to prevent
the cleaner from falling, always place it at bottom
of stairs.
Extra Reach Hose
(Model: VZL-6017Conly)
The Extra Reach hose provides easier cleaning of stairs
and hard to reach places.
Follow the steps below for attaching and detaching the
Extra Reach hose.
Turn cleaner OFF before disconnecting and connecting
hose. Remove hose end from dirt duct (A) (Fig.5/4).
Align end of Extra Reach hose with projections (B) over
slots on dirt duct (C). Slide hose into slots and twist hose
to lock it into place.
Align end of hose with projections (D) over slots (E) on
Extra Reach hose.
Slide hose into slots and twist hose to lock it into place
(Fig.5/5). (To detach hose, reverse procedure.)
Attach wands or tools to the other end of hose.
Note: Hose must be connected to dirt duct and hose
tube after removing Extra Reach hose for carpet or
floor cleaning.
Fig.5/4
Fig.5/5
A
A
B
C
D
E
Fig.5/3
!
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 7
www.vax.co.uk
8
maintenance
6. Maintenance
Familiarise yourself with these home maintenance
tasks as proper use and care of your cleaner will
ensure continued cleaning effectiveness.
Emptying the Dirt Cup
Empty the dirt cup before the dirt reaches the fill line (A).
Place the cleaner in the upright position before removing
the dirt cup (Fig.6/1).
Disconnect cleaner from electrical outlet. Do not use
cleaner without dirt cup or filters in place.
CAUTION: Very fine materials, such as plaster dust or
cornstarch, may seal the filter and cause a reduction
in performance. When using the cleaner for this type
of dust, empty the cup and clean the filters often.
Press dirt cup release button (A) and pivot cup out
(Fig.6/2).
Holding dirt cup over trash receptacle, press dirt cup door
release button (A) to open dirt cup door (B) (Fig.6/3).
Close door and press dirt cup door release button to latch
dirt cup door closed. Place bottom of dirt cup into cleaner
body first. Pivot cup into cleaner body (Fig.6/4).
Press on dirt cup release button while firmly pressing on
dirt cup.
Release button in order for it to return to proper position
and lock the dirt cup into place (Fig.6/5).
A
B
Fig.6/3
Fig.6/4
Fig.6/5
A
A
!
Fig.6/2
Fig.6/1
A
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 8
C
leaning the Filters
Cyclonic Filter Assembly
IMPORTANT: Disconnect cleaner from electrical
outlet. Do not operate cleaner without dirt cup
or filters in place.
R
emove dirt cup as previously described (Fig.6/2).
Twist filter assembly (A) counterclockwise.
Remove assembly from dirt cup (Fig.6/6).
Dirt and debris can be cleaned from the filter assembly
by brushing with the cleaner’s combination tool.
Place the filter assembly on the dirt cup, aligning (3) tabs
(A) on filter with (3) slots on dirt cup (B) and twist it
clockwise to secure into position.
Press dirt cup door release button (C) to latch dirt cup
door closed (Fig.6/7).
Replace dirt cup as described in Figs.6/4 and 6/5.
Secondary Filter
IMPORTANT: Disconnect cleaner from electrical
outle
t. Do no
t oper
a
te cleaner without dirt cup
or filters in place.
R
emo
ve dirt cup as previously described (Fig.6/2).
With thumb and forefinger, slide latch (A) located at the
top of the housing to the right and pull down to remove
gray filter frame.
9
Vax Careline 0870 606 1248
maintenance
Remove black foam filter. Rinse filter frame cartridge and
foam filter under cold water (Fig.6/8).
Allow both filter frame and filter to air dry for 24 hours
before replacing filter into filter frame.
Reposition filter frame cartridge by inserting tabs into
slots on back of housing.
Rotate filter cartridge frame up toward top of housing
and snap closed.
HEPA Final Filter
IMPORTANT: Disconnect cleaner from electrical
outlet. Do not operate cleaner without dirt cup
or filters in place.
With fingers in slots, pull filter frame (A) straight out
(Fig.6/9).
Dirt and debris can be cleaned from the filter cartridge
by brushing with the cleaner’s combination tool,
IMPORTANT: Do not rinse or wash the HEPA
filter cartridge.
Fig.6/9
A
Fig.6/6
B
C
A
A
Fig.6/7
!A!
!
!
Fig.6/8
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 9
www.vax.co.uk
10
maintenance
H
eadlight
IMPORTANT: Disconnect cleaner from electrical
outlet.
Removing Headlight Lens
Press handle release pedal and place handle in low
p
osition. Using a Phillips screwdriver, remove the screw as
shown and lift off lens (Fig.6/10).
Installing Headlight Bulb
Pull old bulb straight out of socket. Push new bulb straight
into socket until locked in place. Excessive force is not
required.
(Fig.6/11).
For replacement bulbs please call Vax
Care line
.
Replacing Headlight Lens
Reposition lens and secure with the screw (Fig.6/12).
B
elts
IMPORTANT: Disconnect cleaner from electrical
outlet.
WARNING: Brush bar can start suddenly. Unplug
cleaner before turning it over.
T
he belts are located under the bottom plate of the
cleaner and should be checked from time to time to be
sure they are in good condition.
Replacing Flat Belt
Replace belt if it is stretched, cut or broken. To check the
flat belt, refer to Fig.6/13.
Removing Bottom Plate
Place handle in low position and turn cleaner over so
bottom side is facing up. Remove the 6 screws as shown
with a Phillips screwdriver. Lift off bottom plate (Fig. 6/13).
Removing Belt
Remove used belt (A) from large pulley (B) and discard
(Fig.6/14).
Positioning Belt
With lettering on outside of belt, slide new belt over motor
sha
ft (A)
. Place o
ther end o
f belt over large pulley (B) while
r
olling the pulle
y in dir
ection shown. Turn brush bar making
sure belt turns freely and is not pinched between brush bar
and agitator shield (Fig.6/15).
Fig.6/13
Fig.6/14
A
B
!
!
Fig.6/11
Fig.6/12
!
Fig.6/10
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 10
Insert brush bar through belt an position belt in groove (A)
on brush bar (Fig.6/18).
Brush bar
IMPORTANT: Disconnect cleaner from electrical
outlet.
WARNING: Brush bar can start suddenly. Unplug
cleaner before turning it over.
Replacing Brush bar
When agitator brushes are worn, the brush bar should be
replaced.
Inspecting Brush bar
To check condition of brushes, move edge of a card
across bottom plate while turning brush bar.
To maintain cleaning effectiveness, replace brush bar if
brushes do not touch card (Fig.6/18).
11
Vax Careline 0870 606 1248
maintenance
Reposition bottom plate and 6 Phillips head screws.
Tighten screws securely (Fig.6/16).
Inspecting V-Belt
The V-belt is designed to last for a long time and is not
normally replaced. However, if the V-belt is cracked, gouged
or broken, it should be replaced.
Slide flat belt off large pulley as shown in Fig.6/14.
To remove V-belt, slide back of belt over pulley (A). Then
firmly pull on belt and ‘snap’ it out. Discard used belt.
To install new belt (with lettering on outside of belt), slide
back of belt over pulley and pull front of belt toward groove
(B) next to pulley. Belt will ‘pop’ into place (Fig.6/17).
Fig.6/16
Fig.6/18
Fig.6/17
A
A
A
B
B
Fig.6/15
!
!
Fig.6/18
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 11
www.vax.co.uk
12
troubleshooting/ uk service & help
8. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 8.00am to 6.00pm.
Saturday-Sunday 9.00am to 5.00pm.
An answerphone is available outside of these hours.
Any queries or concerns about using the Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For
the nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
7. Troubleshooting
WARNING: To reduce the risk of personal injury,
unplug vacuum cleaner before servicing
.
PROBLEM: Cleaner won’t run
Cause:
Not properly plugged into wall outlet.
Solution: Plug in firmly.
Cause: No electricity in wall outlet.
Solution: Check fuse or breaker.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
Cause: Motor thermostat tripped.
Solution: Switch off and unplug the vacuum cleaner.
Leave for one (1) hour. See page 3.
PROBLEM: Cleaner/tools won't pick up
Cause:
Broken or worn belt.
Solution: replace belt.
Cause: Brush bar worn.
Solution: Replace brush bar.
Cause: Dirt container full.
Solution: Empty dirt container.
Cause: Incorrect carpet height setting.
Solution: Move carpet height adjuster to lower setting.
Cause: Blockage in air flow passages.
Solution: Clear blockage.
PROBLEM: Cleaner hard to push
Cause:
Incorrect carpet height setting.
Solution: Move carpet height adjuster to higher setting.
PROBLEM: Smoky/burning smell detected
Cause:
Belt broken or stretched.
Solution: Replace brush bar as described in section 6.
PROBLEM: TurboTool brush bar won’t turn
Cause:
Too much pressure being applied to tool.
Solution: Continue using tool applying light pressure.
Cause: Blockage in turbine channel.
Solution: Remove blockage.
Cause: Low cleaner suction.
Solution: Check items under “Cleaner/tools won’t pick
up” above.
!
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 12
13
Vax Careline 0870 606 1248
technical specification
9. Technical Specification
Voltage: 230 – 240V ~50Hz
Wattage: 1500W
Capacity: 2.6l
Filters: Pre-motor filter assembly
HEPA post motor filter
Cord Length: 8.3m
Weight: 11.8kg
Subject to technical change without notice.
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 13
www.vax.co.uk
14
This page has been left intentionally blank.This page has been left intentionally blank.This page has been left intentionally blank.
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 14
15
Vax Careline 0870 606 1248
This page has been left intentionally blank.
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 15
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
VZL-6017 Mach 7 upright vacuum cleaner is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
W
as
t
e electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
Vax VZL-6017 User Guide v3.qxd 8/1/08 16:49 Page 16
Loading...