DynamoCordless
POWERFUL 2-IN-1 CORDLESS
VACUUM WITH HANDHELD
LET’S GET STARTED.
H85-D-B14
H85-D-B18
Let’s talk safety
Basic
safety
precautions
Don’ts
This vacuum cleaner is intended for household use only
and NOT for commercial or industrial use.
• Only use the vacuum cleaner indoors and keep the area you’re
cleaning well lit.
• Keep ngers, hair and loose clothing from moving parts and
openings whilst using the vacuum cleaner.
• This vacuum cleaner can be used by children aged from 8
years and above and persons with reduced physical, sensory
• Don’t charge the Cordless upright outdoors or leave the charger
connected to the mains when not in use.
• Don’t use this vacuum cleaner if it has been dropped, damaged,
immersed in water or left outdoors.
• Don’t handle the charger plug or use the vacuum cleaner
with wet hands.
• Don’t run over the charger cord or use the vacuum cleaner if the
charger cord or plug is damaged. Please contact our Customer
Care Line on: 0330 026 8455 (Mon-Fri 8:30am to 6:30pm,
Sat 9:00am to 5:00pm).
Do’s
• Always make sure the lter and dirt container are tted correctly
before using your vacuum cleaner.
• Always turn o and unplug the vacuum cleaner from the charger
before carrying out any maintenance.
• Turn o all controls on the vacuum cleaner before disconnecting
or connecting the charger.
• Take extra care when cleaning on the stairs.
• Always protect the charger cord from heated surfaces or near
open ames.
• If charging the vacuum cleaner through an extension cord
use only CE approved 13amp extension cords, non-approved
extension cords may overheat. Care should be taken to arrange
the extension cord as it can be a trip hazard.
or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the vacuum cleaner in
a safe way and understand the hazards involved. Children should not play
with the vacuum cleaner. Cleaning and user maintenance should not be made
by children without supervision.
• Only Vax recommended charger, tools and accessories should be used with
this vacuum cleaner.
• Don’t use the charger cord as a handle, pull the charger cord around corners
or sharp edges or close a door over the charger cord. Don’t unplug charger
by pulling on the charger cord.
• Don’t attempt to remove blockages with sharp objects as this may cause
damage to your vacuum cleaner.
• Don’t use the charger with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
• Don’t vacuum up hot coals, cigarette butts, matches or smoking hot burning
items or use in an area where there may be harmful uids (chlorine, bleach,
and ammonia drain cleaner).
• Always carry the vacuum cleaner/handheld by the correct carry handle.
• Store your vacuum cleaner in a cool, dry area.
• Before any user maintenance is undertaken, refer to the appropriate section
in the user guide to understand necessary precautions required.
• Always use the charger supplied with the vacuum cleaner.
• Always remove the plug from the vacuum cleaner before cleaning
or maintaining the vacuum cleaner.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE.
Thank you for buying this Dynamo Cordless
Taking care of your carpets and hard oors
The Dynamo Cordless is designed to make vacuuming carpets and hard oors regularly,
as eective and ecient as possible and this user guide will help you get the most out
of your machine.
Maintaining your carpets and hard oors will ensure they keep their appearance for longer.
You’ve chosen the carpets and hard oors for your home for a reason and Vax will help you
take good care of them.
Taking care of your Dynamo Cordless
Also inside this guide are instructions on maintaining your new machine, so that it’s always
ready when you are to tackle your carpets and hard oors.
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support
Let us know what you think @VaxUK
Contents
Dynamo Cordless
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Accessories
What to do if it goes wrong
Getting in touch
Included with
your machine
Charger
2-in-1 Crevice Tool
/Dusting Brush
Getting to know your machine
On/O and suction
control switch
2-in-1 crevice tool/dusting
brush holder
Handle recline button
Handheld release button
LED Power/charge lights
Handheld On/O button
Dirt container
release button
Floorhead
LED oorhead
lights
Technical Specication
Name Dynamo Cordless 14.4V
Model No H85-D-B14
Voltage Please refer to product rating label
Wattage Please refer to product rating label
Charge Time 5 hours Run Time 25mins
Weight 3kg
Bin Capacity 0.4l
Subject to technical change without notice.
Machine charging port
Floorhead release button
Name Dynamo Cordless 18V
Model No H85-D-B18
Voltage Please refer to product rating label
Wattage Please refer to product rating label
Charge Time 5 hours Run Time 35mins
Weight 3kg
Bin Capacity 0.4l
*To purchase consumables and accessories, please visit vax.co.uk
Getting started
PLEASE READ ‘LET’S TALK SAFETY’ BEFORE USE
Before you begin
CAUTION: Always switch o the vacuum cleaner before connecting or disconnecting the handheld/attachments or removing
and emptying the dirt container.
IMPORTANT: The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat the
thermostat will automatically turn the vacuum cleaner o. If this happens, switch the vacuum cleaner o. Remove and empty the
dirt container also check the vacuum cleaner for blockages. Allow the vacuum cleaner to cool for approximately 1 hour (if you have
cleaned the lter please wait 24 hours for the lter to fully dry before putting back into the machine). For best cleaning results,
lters require cleaning at least every 3 to 6 months. If the vacuum cleaner is blocked, switch o before removing the blockage.
CAUTION: This vacuum cleaner has a constantly rotating brushbar. Never leave the vacuum cleaner in one spot for an extended
period of time as this may damage the oor surface.
Assembling your 2-in-1 vacuum cleaner
Line up the oorhead with
the main body and push
rmly into place.
Lift the handle in a hinge
like manner and secure
onto the main body.
Store the 2-in-1 tool on
board the vacuum cleaner
by pushing the tool rmly
into the tool holder located
on the handle.
Getting started
Carrying your 2-in-1 vacuum cleaner
Make sure the handle
is secured onto the main.
body and use the handle
to carry as a upright
vacuum cleaner.
Use the handle to carry as a handheld vacuum cleaner.
Charging your 2-in-1 vacuum cleaner
NOTE: Initial charge is 5 hours, charging will be required before rst use. The vacuum can be charged with the handheld either
attached to or detached from the main body.
Plug the charger into the side of the handheld
and plug into mains.
Once fully charged
the LED indicator lights
on the handheld will
illuminate green.
When the vacuum needs
recharging the LED lights
on the handheld will
illuminate red and the
machine will cut out.
Using your machine
CAUTION: The brushbar will constantly rotate. Never leave the vacuum cleaner in one spot for an extended period of time as this
may damage the oor surface. Vax cannot be held responsible for damage to the oor surface if the customer fails to take notice
of this recommendation
As an upright vacuum cleaner
Slide the On/O suction
control switch forward
once for low suction.
The LED lights on the
oorhead will illuminate.
The LED lights on the
handheld will illuminate
green, indicating the power
is on and the brushbar
Unplug the charger from
the mains and from the
side of the handheld.
Place foot on the oorhead
and pull the handle
backwards to recline.
will spin.
Slide the On/O suction
control switch forward
again for high suction.
Slide the On/O suction
control switch all the way
back to switch the power
and LED lights ‘O’.
As a handheld vacuum cleaner
Press the handheld
release button.
Lift to remove the
handheld from the
main body.
Slide the On/O suction
control forward to switch
the handheld on. The LED
lights will illuminate green
indicating the power is on
Using your machine
Using the 2-in-1 tool
CAUTION: Always turn o the vacuum cleaner if anything becomes trapped whilst using the tool.
1 2
1 Crevice tool
2 Dusting brush
For a more detailed clean, line up the 2-in-1 tool the with
the nozzle on the handheld and push rmly into place.
Before returning the
handheld to the main body,
slide the On/O suction
control backwards, to
switch the handheld o.
Pull to remove 2-in-1 tool
from the handheld nozzle.
Taking care of your machine
CAUTION: Always switch o the vacuum cleaner before carrying out any maintenance or troubleshooting.
Emptying the dirt container
Press the handheld
release button.
Lift to remove the
handheld from the
main body.
Lift the lter by the
lter frame out from
the dirt container.
Press the dirt container
release button.
Pull to separate the
dirt container from
the handheld.
Hold the dirt container
over a bin allowing
dirt/debris to fall out.
Taking care of your machine
24hr
Cleaning the lter
CAUTION: For best cleaning results lters require cleaning every 4-6 uses or as needed depending upon use.
Do not use your vacuum cleaner without the lter in place.
Press the dirt container
release button.
Leave for 24hrs or until
fully dry before replacing.
Pull to separate the
dirt container from
the handheld.
Lift the lter by the
lter frame out from
the dirt container.
Ret the lter making
sure the lter frame is
correctly lined up in the
dirt container.
Cleaning the terminals
CAUTION: For best performance all terminals must be free from dust and dirt.
Tap the lter over a bin
to remove any dirt/debris.
Wash the lter under
running water
(40 degrees max).
Using a dry cloth or soft dusting brush remove any dust/debris from terminals on main body and handheld.
Taking care of your machine
Clearing blockages
CAUTION: Use a blunt instrument such as a broom handle or something similar when removing a blockage from the main body
or oorhead.
Press the handheld
release button.
Remove any blockage from the main body or oorhead.
Lift to remove the
handheld from the
main body.
Press the oorhead
release button.
Pull to remove the
oorhead from
the main body.
Taking care of your machine
Clearing a blockage from the brushbar
CAUTION: If the brushbar has been obstructed, the Motor Protection Sensor may have been activated. Remove the handheld
and oorhead and clear any obstruction from the brushbar. Wait 30 minutes for the vacuum cleaner to reset itself. Replace the
handheld and oorhead and retry.
Using a pair of scissors remove any threads or hair
caught around the brushbar.
Remove the brushbar lifting the side of the brushbar
nearest the release lock rst.
To release the brushbar pull and lift the release lock
located underneath the oorhead.
Replace the brushbar. Fit the inverted round end of the
brushbar rst, then line up and push the other side of
brushbar into the oorhead. Ret the release lock.
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
Pre-motor lter (Type 132)
1-7-137521
2-in-1 tool (Type 3)
1-9-137520
A replacement 2-in-1 tool for your
Dynamo Power cordless vacuum.
What to do if it goes wrong
SolutionProblem
• Check the vacuum cleaner is fully charged. Go to ‘Getting started’.
• Check the charger is plugged into the mains and correctly connected
Why does my vacuum
cleaner have no power?
Why isn’t my vacuum
cleaner charging?
Why won’t the vacuum
cleaner pick up?
to the vacuum cleaner. Go to ‘Getting started’.
• Check the handheld has been correctly tted into the main body.
• Check the terminals on the main body and handheld are clean. Go to ‘Taking
care of your machine – Cleaning the terminals’.
• If the brushbar has been obstructed, the Motor Protection Sensor may
have been activated. Remove the handheld and oorhead and clear any
obstruction from the brushbar. Wait 30 minutes for the vacuum cleaner
to reset itself. Replace the handheld and oorhead and retry.
• Check the charger is plugged into the mains and correctly connected
to the vacuum cleaner. Go to ‘Getting started’.
• Check the terminals on the main body and handheld are clean. Go to ‘Taking
care of your machine – Cleaning the terminals’.
• Check the charger cable for damage. If damaged please contact our
Customer Service Line on: 0330 026 8455 (Mon-Fri 8:30am to 6:30pm,
Sat 9:00am to 5:00pm).
• Empty the dirt container and clean lter. Go to ‘Taking care of
your machine’.
• There may be a blockage in the vacuum cleaner. Go to ‘Taking care of your
machine – Clearing blockages’.
• The brushbar may not be turning. Go to ‘My brushbar isn’t turning?’ below.
• The vacuum cleaner may need recharging. Go to ‘Getting started’.
• Low suction has been selected, increase to high suction. Go to ‘Using
your machine’.
• If the brushbar has been obstructed, the Motor Protection Sensor may
have been activated. Remove the handheld and oorhead and clear any
My brushbar
isn’t turning
obstruction from the brushbar. Wait 30 minutes for the vacuum cleaner
to reset itself.
• Replace the handheld and oorhead and retry the brushbar may
be blocked. Go to ‘Taking care of your machine – Clearing a blockage
from the brushbar’.
• The LED lights on the handheld will turn Red when the vacuum
cleaner needs recharging. Go to ‘Getting stared’.
Why has the LED
light turned Red ?
Caution: Always unplug the steam cleaner before performing maintenance/troubleshooting checks.
Getting in touch
† Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
GET IN TOUCH
0330 026 8455 VaxVacuumsinfo@vax.co.uk vax.co.uk @Vax UK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
H85-D-B14 and H85-D-B18 and are manufactured in compliance with the following Directives: Safety: 2006/95/EC Low
Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
© 2015 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.
Loading...