vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 6061248
instruction manual
Bagless cylinder
Vax model number:
VZL-118 Series
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 1
VZL-118
1. Diagram
vax.co.uk
2
parts overview
1 2
8
9
3 4
5 6
7
Fig.1/1
Fig.1/2
1 Dirt container locking button
2 Carry handle
3 Auto cord rewind
4 Blocked filter indicator
5 Power indicator
6 On/off button
7 Post-motor filter
8 Wheel
9 Dirt container
10 Hose inlet
11 Dirt container carry handle
12 Combination floor head
(Model:VZL-118P & VZL-118PS only)
13 TurboTool (Model:VZL-118P & PS only)
14 Upholstery tool
15 Telescopic extension tube
16 TurboBrush
(Model:VZL-118AT, PS & C only)
17 Hard floor tool
(Model:VZL-118AT, PS & C only)
18 Stretch hose
(Model:VZL-118AT, PS & C only)
19 Flexible hose
a - Crevice tool b - Dusting brush
20 TurboTool Connector
(Model:VZL-118P & PS only)
1
0
11
14
13
12
15
16
17
20
a
19
b
18
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 2
3
V
ax Careline 0870 606 1248
safety information
2. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.
4. Children should be supervised to ensure that they
do not play with the appliance.
5. The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
6. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.
7. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified
person for examination, repair or adjustment.
8. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.
9. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
10. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
12. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
13. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.
14. Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).
15. Do not vacuum up hard or sharp objects such as
glass, nails, screws, coins, etc.
16. Do not use without the filters in place.
17. Take extra care when vacuuming stairs.
18. Keep vacuuming area well lit.
19. Store the vacuum cleaner indoors in a cool, dry area.
20. Turn off the on/off switch before unplugging the
vacuum cleaner.
21. Use only CE-approved 13 amp extension cords.
Non-approved extension cords may overheat. Care
should be taken to arrange the cord so that the cord
cannot be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.
CAUTION: The vacuum cleaner is a very
powerful unit. Before plugging the cord into
the electrical outlet, make sure the switch is in the
‘off’ position.
IMPORTANT: If the inlet, hose or telescopic
tube is blocked, switch off the vacuum cleaner
and remove the blockage(s) before re-starting the
vacuum cleaner.
IMPORTANT: Cleaning filters improves vacuum
performance. Make sure all the filters are
completely dry before inserting back into the vacuum
cleaner.
This vacuum cleaner is intended for household use only
and not for commercial or industrial use.
!!!
!
Motor Thermostat
IMPORTANT: The motor is equipped with a thermal
cut-out. If for any reason, the vacuum cleaner should
over-heat, the thermostat will automatically turn the
unit off. Should this occur, unplug the vacuum cleaner
from the electrical outlet and turn off the switch.
Remove the dirt container and empty. Clean the
filters. Allow the cleaner to cool for approximately one
(1) hour. To re-start, plug into an electrical outlet and
switch back on.
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 3
vax.co.uk
4
assembly / operation
3. How to Assemble
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet before assembling or
removing the accessories.
1. Insert the flexible hose into the inlet on the main body
of the vacuum cleaner. Push in until it clicks into
position (Fig.3/1).
2. Push the telescopic extension tube on to the end of
the handle (Fig.3/2).
3. The telescopic extension tube can be lengthened or
shortened by pushing the button in and sliding the
tube apart or together as required (Fig.3/3).
4. Fit the combination floor head
(Model: VZL-118P & PS
only)
or TurboBrush (Model: VZL-118AT, PS & C only) or
Hard Floor tool head (Model: VZL-118AT & C only) by
pushing onto the extension tube (Fig.3/4).
4. How to Operate
Cord Release
Fully unwind the power cord. A yellow mark on the power
cord indicates the recommended cord length. Do not
exceed the cord length beyond the red mark.
On/Off Button
Insert the power plug into the electrical outlet. Ensure the
vacuum cleaner is switched off.
Press the on/off button located on the top of the vacuum
cleaner and press the button again to turn the vacuum
cleaner off.
Carpet Cleaning
Model VZL-118P & PS only: For carpet and rug cleaning
press the rocker switch on the combination floor head to
raise the brushes.
Model VZL-118AT
, PS & C only: Attach the TurboBrush
floor head to the end of the extension tube. (NOTE:
TurboBrush: for pet hair, stair and large carpeted areas.
NOT recommended for hard floors.)
Hard floor cleaning
Model VZL-118P & PS only: For hard floor cleaning, press
the rocker switch on the combination floor head to lower
the brushes.
Model VZL-118AT & C only: Attach the hard floor tool
head to the end of the extension tube. (NOTE: For parquet
and laminate coverings).
TurboTool
(Model: VZL-118P & PS only):
IMPORTANT: The TurboTool connector must be
added to the handle before the TurboTool may
be attached.
for vacuuming up pet hair, stair and upholstery cleaning.
(NOTE: Do not use the TurboTool on suede and leather
surfaces).
Stretch hose (Model: VZL-118AT, PS & C only): For full
height stair cleaning (NOTE: This should not be used as the
main vacuum hose).
NOTE: For stair cleaning, the unit should always be
placed at the bottom of the stairs.
NOTE: The stretch hose is recommend to be used for a
period of 20 minutes max.
Cord Rewind
To rewind the power cord, press the cord rewind button,
located on the top of the vacuum cleaner, and guide the
power cord with one hand. This will prevent the cord from
whipping which could cause damage or injury.
Carry Handle
Use the carry handle located on the top of the machine to
move the vacuum cleaner from room to room.
Fig.3/1
Fig.3/2
Fig.3/3
Fig.3/4
!
!
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 4
5
V
ax Careline 0870 606 1248
operation / accessories
Hose Storage
For convenience there is a slot located located on the rear
of the vacuum cleaner where the floor tool and hose can
be parked for carrying and storage.
Power Indicator
Located behind the carry handle on the top of the unit, a
green light will indicate that the machine is working
correctly.
Blocked Filter Indicator
Located behind the carry handle on the top of the unit, the
indicator light will illuminate red when the filter or dirt
container has become blocked. When this occurs, empty
the dirt container and check the filters.
5. Accessories
The accessories can be attached directly to the handle by
removing the telescopic tube and pushing in the desired
accessory.
The accessories can also be attached to the telescopic
tube for extra reach. Remove the combination floor head
and push on the desired accessory.
Dusting brush: for delicate surfaces.
Upholstery tool: for carpets, upholstery, stairs, etc.
Crevice Tool: for crevices, corners and cracks, etc.
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 5
vax.co.uk
6
dirt containers
6. Dirt Container: Removal
and Replacement
WARNING: Always unplug the vacuum cleaner
from the electrical outlet before removing the
dirt container.
WARNING: Do NOT use the vacuum cleaner
without ALL of the filters and dirt container in
place.
Emptying the Dirt Container
NOTE: The dirt container must be emptied every time
the dirt reaches the max line.
After removing the flexible hose, press the dirt containerlocking button on the top of the machine (Fig.6/1)
Remove the dirt container and position over a rubbish bin.
Press catch one (1) first, followed by catch two (2) (Fig.6/2)
When all the dirt has fallen the dirt container may be wiped
with a damp cloth to clean. Allow to air dry completely
before closing the dirt container bottom. Then return the
dirt container bin back to the unit, a click will be heard
when the bin is in the correct position.
Cleaning the dirt container
When all the dirt has fallen the dirt container and
separators may be wiped with a damp cloth to clean. To
gain better access to the dirt container, the lid and bin can
be separated by lifting the release catch at the back of the
dirt bin (Fig.6/3).
The separators and dirt bin may then be wiped with a
damp cloth to remove dirt residue (Fig.6/4).
Allow to air dry completely before re assembling the bin.
The bin is reassembled by locating the tabs on the front of
the dirt bin with the lid. Press down the lid on to the dirt
bin until a click is heard.
!
Fig.6/1
Fig.6/3
Fig.6/5
Fig.6/2
!
!
1
2
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 6
7
V
ax Careline 0870 606 1248
cleaning filters
7. Cleaning the Pre- and
Post-motor filters
NOTE: The pre-motor filter should be cleaned
frequently and the post-motor filter should be cleaned
every 9 - 12 months. Vax recommends frequently
cleaning the filters to optimise the performance of the
vacuum cleaner.
NOTE: Do not use any detergents or boiling water to
wash the filters.
Cleaning the Pre-motor Filter
Remove the dirt container as previously directed.
Remove the foam filter frame from the back of the dirt
container and separate the foam filter from the frame
(Fig.7/1).
Remove the foam filter and fabric filter cassette from the
main body of the unit (Fig.7/2)
The filters may then be tapped against the side of a
rubbish bin and may then be rinsed in luke warm water
(max 40°C). Allow to air dry for at least 24 hours before
replacing back in the unit.
Cleaning the HEPA Post Motor Filter
NOTE: This is located at the rear of the vacuum
cleaner.
Release the post-motor cover by pressing in the catch at
the top of the cover. The filter can be removed by pulling
on the tab. The filter may be tapped against the side of a
rubbish bin to remove dust particles (Fig.7/4).
The HEPA post-motor filter may be rinsed in luke warm
water (max 40°C). Allow to air dry for at least 24 hours
before replacing (Fig.7/5).
Fig.7/1
Fig.7/5
Fig.7/4
Fig.7/2
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 7
vax.co.uk
8
cleaning blockages
8. Cleaning Blockages
WARNING: To reduce the risk of electric shock,
the power cord must be disconnected before
performing maintenance/troubleshooting checks.
1. Turn the vacuum cleaner off and unplug from the
electrical outlet.
2. The flexible hose and stretch hose
(Model: VZL-118AT
&
PS only)
can be disconnected from the vacuum
cleaner by pressing the release catch on the top of
the hose connector and pulling away from the
machine. Remove any blockages found then
reconnect the hose securely.
Removing debris from the TurboBrush
(Model: VZL-118AT, PS & C only)
The brushbar will stop rotating if it is blocked during
operation by vacuuming up foreign objects, or is strands of
carpet are wrapped around it.
Switch the vacuum cleaner off and disconnect the power
plug from the electrical outlet.
Lay the TurboBrush floor head on a flat surface and turn
over to expose the brushbar. Using a pair of scissors, cut
through any threads or hairs caught by the brushbar that
have wrapped around the guides (Fig.8/1).
Removing debris from the TurboTool
(Model: VZL-118P & PS only)
Switch the vacuum cleaner off and disconnect the power
plug from the electrical outlet.
Rotate the locking ring 180º (Fig.8/2).
Lift the top cover off and remove any blockage (Fig.8/3).
To re-assemble, ensure that the tabs are engage. Pivot the
lower housing closed and rotate the locking ring 180º
(Fig.8/3).
!
Fig.8/1
LOCKING RING
Fig.8/2
TABS
Fig.8/3
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 8
9
V
ax Careline 0870 606 1248
storage / troubleshooting
9. Storage
IMPORTANT: Always unplug the vacuum cleaner
from the electrical outlet and rewind the power
cord as directed before storing.
NOTE: Always store the vacuum cleaner base down.
10. Troubleshooting
WARNING: To reduce the risk of personal injury,
unplug the vacuum cleaner before performing
maintenance or troubleshooting checks.
PROBLEM: Vacuum cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in securely.
Cause: No electricity in the electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the vacuum cleaner.
Leave for one (1) hour before switching the
vacuum cleaner back on.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won’t pick up/loss of suction.
Cause: Dirt container not installed properly.
Solution: Review dirt container replacement.
Cause: Dirt container full or blocked.
Solution: Empty dirt container.
Cause: Clogged filters.
Solution: Remove, clean and replace filters.
PROBLEM: Accessories won’t pick up.
Cause: Accessories are not attached correctly.
Solution: Refer to section 5.
Cause: TurboBrush / TurboTool is clogged.
Solution: Refer to section 7.
Cause: Hose / Stretch Hose is not installed correctly.
Solution: Refer to section 7.
!
!
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 9
vax.co.uk
10
PROBLEM: Dust escaping from the vacuum cleaner.
Cause: Dirt container full.
Solution: Empty dirt container.
Cause: Dirt container not installed correctly.
Solution: Review dirt container replacement.
Cause: Hose / Stretch Hose is not installed correctly.
Solution: Review installation.
Cause: Filter not installed completely.
Solution: Remove, clean and replace filters.
11. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 8.30am to 6.30pm.
Saturday-Sunday 9.00am to 5.00pm.
Any queries or concerns about using the Vax, call the Vax
Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
troubleshooting / uk service & help
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 10
11
V
ax Careline 0870 606 1248
12. Technical Specification
Voltage: 220-240V ~50Hz
Wattage: 1400W
Capacity: 2 litres
Filters: Dirt container - wipeable
Foam pre-motor filter - washable
Fabric pre-motor filter - washable
HEPA post-motor filter - washable
Cord length: 6.0m approx
Weight: 6.7kg
Subject to technical change without notice.
technical specification
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 11
---
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
VZL-118 Series Force3 cylinder range is manufactured in compliance
with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Wasteelectrical products should not be disposed of with household waste.Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: vax.co.uk
Vax VZL-118 Series User Guide.qxd:04.09 24/4/09 10:06 Page 12
Loading...