Vax Flair Easy-Store U86-FN-Pe User Manual

vax.co.uk

U86-FN-Pe

Flair
Easy-Store™

Let’s get started

Project: Flair Easy-Store Pet

Project: U86-IN-e_Series_UG

Upload date:

Job No: J2543 Model No: U86-FN-Pe

Model No:

Proof No: 2 Designer: ACW PM: Size (HxW):

Size (HxW): Colours used:

Not

used

In

Progress

Final

Artwork

Barcode No.: Part No.:

165C

C

M Y K

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 1 01/07/2014 14:14

Let’s talk safety

Do’s

Basic safety precautions

3 Turn o all controls on the vacuum

cleaner before disconnecting or
connecting the power cord.

3 Always make sure lters are in place

before use.

3 Always switch o the

vacuum cleaner before
disconnecting or connecting
the hose and accessories.

3 Keep all openings clear and free

from debris as this may aect the
airow/suction.

3 Always replace the fuse in the plug

with a British 13amp fuse. Always
protect the power cable from heated
surfaces and open ames.

3 Take extra care when positioning

and using the vacuum cleaner
on the stairs.

3 Use only CE approved 13amp

extension cords, non-approved
extension cords may overheat.
Care should be taken to
arrange the extension cord
as it can be a trip hazard.

3 Store your vacuum cleaner in a cool,

dry area. If lters have been cleaned
as per user guide instructions
ensure they are thoroughly dry
before storing away.

Don’ts

8 Don’t use this vacuum cleaner if

it has been dropped, damaged or
left outdoors.

8 Don’t run over the power cord or use

vacuum cleaner if the power cord or
plug is damaged. Please contact our
Customer Care Line on: 0330 026
8455 (Mon-Fri 8.30am to 6.30pm,
Sat 9.00am to 5.00pm).

8 Don’t handle the plug or use the

vacuum cleaner with wet hands.

8 Don’t pull or carry this vacuum

cleaner by the power cord. Don’t use
the power cord as a handle, pull the
power cord around corners, sharp

edges or close a door over the power
cord. Don’t unplug vacuum cleaner
by pulling on the power cord.

8 Don’t vacuum up any ammable

or combustible materials (lighter
uid, petrol, kerosene etc.) or use
the vacuum cleaner in an area with
explosive vapours or liquid.

8 Don’t vacuum up hot coals, cigarette

butts, matches or smoking hot
burning items or use in an area
where there may be harmful uids
(chlorine, bleach, and ammonia
drain cleaner).

This vacuum cleaner is intended
for household use only and NOT for
commercial or industrial use.

• Only use the vacuum cleaner indoors
on dry surfaces and keep the area
your cleaning well lit.

• Keep ngers, hair and loose clothing
from moving parts and openings
whilst using the vacuum cleaner.

• This vacuum cleaner can be used
by children aged from 8 years and
above and persons with reduced
physical, sensory or mental

capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the vacuum cleaner in a safe
way and understand the hazards
involved. Children shall not play with
the vacuum cleaner. Cleaning and
user maintenance shall not be made
by children without supervision.

• Only Vax recommended tools should
be used with this vacuum cleaner.

Please keep instructions for
further use.

Don’ts

8 Don’t attempt to remove blockages

with sharp objects as this may cause
damage to your vacuum cleaner.

8 Don’t vacuum up hard or sharp

objects such as glass, nails,
screws or coins etc.

8 Don’t use the vacuum cleaner with

incorrect voltage as this may result
in damage or injury to the user.
The correct voltage is listed on the
ratings label.

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 2-3 01/07/2014 14:14

Contents

Let’s talk safety

Getting to know your machine

Getting started

Using your machine

Taking care of your machine

Let’s talk technical

What to do if it goes wrong

Getting in touch

Accessories

Notes

Flair Easy-Store™

Included with
your machine

Flair Easy-Store™

+

TurboTool

Fur ‘n’ u tool

Extension hose 1.5m

Dusting brush

Crevice tool

Hard oor tool

Initial Setup for normal operation

1. Use the base accessories.
a. Shortest hose
b. Extension tube set to shor test practicable length.

2. Clean lters installe d.

3. Du st receptacle empty.

4. All Bleeds mu st be closed.

5. Variable Power set to M aximum.

6. Floor hea ds/too ls set to Carpet Mode for carpet clea ning.

7. Mechanical Agitation turn ed ON for carpet cleaning.

8. Floor head s/too ls set to Hard Floor Mode for hard oor clea ning.

9. Mechanical Agitation turn ed OFF for hard oor cleaning.

Extension tube

Taking care of you

We’re here if you need us. Instead of taking me back
to the shop, simply visit:

vax.co.uk/support or call:

(UK) 0330 026 8455 (ROI) 1-800 928 308

Monday-Friday 8.30am to 6.30pm, Saturday 9.00am to 5.00pm

Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.

Alternatively, you can write to us at:

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK

This user guide can also be found online at: vax.co.uk/support

Let us know what you think @VaxUK

Thank you for buying this Flair Easy-Store™.

Taking care of your carpets

The Flair Easy-Store™ is designed to make washing carpets regularly, as eective and ecient as
possible and this user guide will help you get the most out of your machine.

Maintaining your carpets will ensure they keep their appearance for longer and smell fresh and
clean. You’ve chosen carpets for your home for a reason and Vax will help you take good care
of them.

Taking care of your Flair Easy-Store™

Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets.

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 4-5 01/07/2014 14:14

Assembling your vacuum cleaner

Lift handle up and click
into place.

Slide 2 in 1 Dusting Brush onto
dust brush holder with brushes
facing outwards.

Line up latch on accessory hose,
push until clicks into place.

Line up turbo tool brushes into
turbo tool holder, push into place
until it clicks (some models only).

Push accessory hose into
hose to machine connector.

Push extension tube and
crevice onto holder.

Before you begin cleaning

WARNING: Always switch o the vacuum cleaner before connecting
or disconnecting the hose/attachments or removing and emptying the
dirt container.

IMPORTANT: The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat
the thermostat will automatically turn the vacuum cleaner o. If this happens switch the vacuum cleaner o and unplug
from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for blockages. Allow the
vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please wait 24 hours for the lters to fully
dry before putting back into the machine).

Filters require cleaning at least every 3-6 months. If the vacuum cleaner is blocked, switch o and unplug before removing
the blockage.

When the vacuum cleaner is stood in the upright position, or when using the hose and tools the brush bar height adjuster
must be set to the highest setting.

Getting to know your machine Getting started

PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE

Extension tube
and crevice

Handle release button

Dust brush holder
(some models only)

Handle

Turbo tool holder
(some models only)

Carry handle

Dirt container
release button

Separator

Dirt container lid

Dirt container

HEPA pre-motor lter
(hidden)

Dirt release clip

Upper release
cord hook

Hose to machine
connector

Height adjuster dial

Name Flair
Voltage 220-240V-50Hz
Wattage 850 Air Watts
Cord length 8m
Weight 7.5kg

Technical Specication

Subject to technical change without notice.

Filter Kit (Type 110)

1-1-134394-00

Belt Kit Type 25
1-1-134411 -00

Turbo Tool Type 6*

1-1-134419-00

Crevice Tool (Type 16)

1-1-134427-00

Dusting Brush (Type 10)

1-1-134426-00

Pro Cleaning kit

(1-1-133326-00)

Accessories & Consumables

* Selected models only.

To purchase consumables and accessories, please visit vax.co.uk

Hose connector

Hose inlet

On/o button

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 6-7 01/07/2014 14:14

Hard oor cleaning

Using your machine Using your machine

Hard oor cleaning tool.

Line up oor tool with base of vacuum
cleaner, push it until it clicks into place.

Lie vacuum cleaner on its
back exposing brush bar.

Hold vacuum cleaner with brush bar over tread of stairs.

Using on the stairs

Always raise the height of the brush bar to hard oor setting when using the
vacuum cleaner on lino and hard oor.

TIP

Filters require cleaning at least
every three months.

This vacuum cleaner
has a constantly rotating
brush bar. When cleaning
on stairs raise the height

adjuster dial to the highest
setting. The brush bar
must overhang the stair
tread. Always take care

when cleaning stairs.

WARNING

TIP

For best performance use your
vacuum cleaner with only the
accessory hose attached.

Plug vacuum cleaner into the
mains, switch on. Turn brush
bar height adjuster dial to
desired setting.

Press On/O button to
switch on.

Place foot on oor head
and pull handle to recline.

Pull hose out of hose
to machine connector.

Attach accessory
to tube/hose.

Attach accessory hose to
extension hose.

If required attach extension
hose to extension tube.

Using accessories

Choose an accessory.

The accessories can be attached to the extension tube or directly to the hose.

When using accessories on the hose/extension tube raise the height adjuster to the highest setting.

IMPORTANT: Always switch o and unplug the vacuum cleaner before connecting or disconnecting the hose/
attachments, or removing and emptying the dirt container.

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 8-9 01/07/2014 14:15

Cleaning the post motor lter

Cleaning the separator

Storing your vacuum cleaner

Wrap the power
around the quick
cord release hooks.

Press handle
release button.

Lower handle
downwards.

Press post motor
lter cover clip, pull
to remove.

Turn separator
anti-clockwise
to ‘unlock’, pull
to remove.

Remove any dirt/
debris. Rinse under
water (max 40°C).

Using a soft brush
clean any dirt/debris
out of the separator.

Remove post
motor lter.

Tap separator over
a bin to remove any
dirt/debris.

Leave to dry for 24
hours or until fully dry
before placing back in
the vacuum cleaner.

24hr

Always use the carry
handle to lift and carry
the machine.

Line up tabs on
separator with dirt
container, turn
separator clockwise
to ‘lock’ and click
into place.

The separator
should sit on seal
in bottom of dirt
container when
correctly tted.

Taking care of your machine Taking care of your machine

Press the dirt container
release button, pull to remove.

Emptying the dirt container

Cleaning the HEPA pre-motor lter

Hold dirt container
over a bin.

Press the dirt release clip,
allowing dirt/debris to fall out.

Turn the dirt container
release button, pull
to remove.

24hr

Leave to dry for
24 hours or until
fully dry before
placing back in the
vacuum cleaner.

Turn the HEPA
pre-motor lter
anti-clockwise,
pull to remove.

Tap HEPA pre-motor
lter over a bin to remove
any dirt/debris.

Rinse under water
(max 40°C).

Line up HEPA
pre-motor lter tabs
in dirt container lid,
turn clockwise until it
clicks into place.

IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the machine should overheat,
the thermostat will automatically turn the machine o. Switch o and unplug the vacuum cleaner. Check the
machine for blockages and clean the lters. Wash the lters with warm water (40°C max) and leave for 24 hours
or until fully dry before replacing into the machine.

Filters require cleaning at least every 3-6 months (depending on the level of use).

Don’t use your vacuum cleaner without all the lters in place.

TIP

Don’t over ll the dirt
container to avoid blocking
the air ow through the
vacuum cleaner and replace

lters every 6-9 months.

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 10-11 01/07/2014 14:15

Removing dirt/debris from TurboTool (some models only)

Removing debris from the brushbar

Using a pair of
scissors cut any hair
or debris free from
around the brushes.

Line up the tabs on front
of the housing and re-t.
Slide locking ring into
groove to secure.

Slide the locking ring
to remove.

Using a pair of scissors
remove any threads or
hair caught around the
brush bar.

Tabs

Lift and separate
the housing.

Taking care of your machine Let’s talk technical

IMPORTANT: Unplug and switch o vacuum cleaner before performing maintenance or troubleshooting checks.

TIP

To test for a blockage in the

hose, drop a small ball of
paper through the hose. The
paper will drop through if the
hose is clear.

Pull hose out of hose to
machine connector.

Wrap hose around hose guide. Over and behind carry handle.
Into hose to machine connector.

Attach accessory hose
to extension hose.

Storing extension hose on vacuum cleaner (optional)

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 12-13 01/07/2014 14:15

• Check the ‘This pack contains’ panel on the box to make sure the
part is included with your vacuum cleaner.

• The plug may not be fully pushed into the electrical socket.

• Check the fuse in the plug if this needs replacing, always replace with a
13amp fus e.

• The motor therm ostat may have tripped. If this has happened, u nplug
the vacuum cleaner. Remove and empty the dirt container and check the
hose for blockages. Clean the lters and allow the vacu um cleaner to cool
for approximately 1 hour (if you h ave washed the lters you will n eed
to wait 24 hours for the lters to fully dry before pu tting them back into
the vacuum cleaner).

• The brushbar may be clogged, check the brush bar and clear any
hair or debris. Go to ‘Let’s talk technical’.

• The belt might be broken, go to ‘Let’s talk technical’.

• There may be a blockage in the hose. Please remove the hose from the
vacuum cleaner, check and clear any blockages. Go to ‘Let’s talk technical’,

• Empty the dirt container and clean lters. Go to the ‘Taking care of your
machine’ page*.

• The brushbar may not be turning. Go to ‘My brushbar isn’t turning?’ below.

• The brush bar height adjuster dial may not be set to the correct setting. Go to
‘Using your machine’.

• If the accessory/tool will not pick up, check and clear any blockages. Go to
‘Let’s talk technical’.

SolutionProblem

Let’s talk technical

Is there an accessory
missing?

Why does my vacuum
cleaner have no power?

Why won’t the vacuum
cleaner pick up?

My brushbar
isn’t turning?

What to do if it goes wrong

Replacing the belt

Place belt on rounded
area of brush bar
without bristles.

Line up right side of
brush bar with base,
push into place. Lift and
push left side of brush
bar until clicks into place.

Lie vacuum cleaner
on its back exposing
brush bars. Use a cross
head screwdriver.
Undo 5 screws

Line up brush bar
cover, push until it
clicks into place.
Replace 5 screws
and tighten.

Lift to remove
brush bar cover.

Lift to remove brush
bar. Remove and
dispose of old belt.

Clean any debris from spindle.
Place new belt on spindle.

Pull hose out of
hose to machine
connector.

Lift clip under the
hose inlet.

Pull latch out and
remove hose.

Remove any
blockage by
inserting wire coat
hanger into hose.

Line up latch,
push until it clicks
into place.

Removing a blockage from the hose

If the brush bar does
not rotate easily then
the belt may not have
been tted correctly.

Make sure the belt is
not twisted.

WARNING

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 14-15 01/07/2014 14:15

* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the vacuum cleaner before calling.

Getting in touch

Don’t forget your accessories!

Order at: www.vax.co.uk/spares-and-solutions

Accessories

TurboTool (Type 6)
1-1-134419-00

Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking up
stubborn pet hair.

Pro cleaning kit (Type 2)
1-1-133326-00

All our best tools all in one kit that makes cleaning
your home quicker, easier and with even better results.
We’ve taken care of cleaning all of the hard to reach
areas such as on top of cupboards and in between
blinds to the dust that collates behind and
within the radiator.

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 16-17 01/07/2014 14:15

Notes Notes

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 18-19 01/07/2014 14:15

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
email: [e-mail] website: vax.co.uk

Version 1.0

EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility,

declare that the U86-AN-(Be, Pe) is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.

@VaxUK

© 2014 All rights reserved. VAX®, VAX Lozenge, are trade marks or registered trade marks of Techtronic Floor Care Technology Ltd.

U86-FN_Pe_FlairEasy-Store_UG_[J2543]_Amd_01.07.14.indd 20 01/07/2014 14:15