DCS2V1MP
DCS3V1HP
LET’S GET STARTED.
Power
DEHUMIDIFIER
REDUCES MOISTURE FAST
Basic
safety
precautions
Don’ts
Do’s
This machine is intended for household use only and NOT for
commercial or industrial use.
• Only use the appliance indoors and keep away from open
external doors and windows.
• Keep ngers, hair and loose clothing away from moving parts and
openings whilst using the appliance.
• This appliance can be operated by children aged from 8 years
and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge, if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without
supervision.
• Always position the appliance on a at, stable, solid surface and never over
stretch the power cord.
• Always remove the water tank and drain the appliance before carrying
or transporting.
• Position the appliance where air is not drawn across your body or head
while sitting or sleeping.
• Don’t leave water stored in the water tank between uses.
• Don’t cover the appliance with washed clothes or position under
washed clothes as water may drip onto the appliance.
• Don’t place the appliance near sources of heat, such as stove
tops, ovens, radiators, open res, candles or computers.
• Don’t position the appliance underneath or near to smoke alarms.
• Don’t move or tilt the appliance when in use. Leaking from the
water tank may occur.
• Don’t use the appliance if the power cord or plug is damaged.
Please contact our Customer Service Line on: 0330 026 8455
(Mon-Fri 8:30am-6:30pm Sat 9:00am-5:00pm).
• Don’t use the appliance if it has been dropped, damaged
or left outdoors.
• Don’t run the power cord under rugs, runners or carpets as it can
be a trip hazard.
• Don’t pull, carry or trap the power cord under doors or sharp edges.
• Don’t handle the plug or appliance with wet hands.
• Don’t unplug the appliance by pulling on the power cord.
• Don’t use the appliance in an area with toxic/explosive vapours/liquids, oxygen
water tanks or near to ammable, combustible materials (lighter uid, petrol,
kerosene, chlorine, bleach and ammonia drain cleaner etc).
• Don’t use the appliance with incorrect voltage as this may result in damage
or injury to the user. The correct voltage is listed on the ratings label.
• Don’t use without the lter in place.
• Inspect the appliance regularly and remove any dust/dirt build
up as this may aect the airow.
• Keep all openings/grills clear and free from obstruction and
sources of heat, open ames including candles. Don’t attempt
to remove blockages with sharp objects as this may cause
damage to the appliance.
• Turn o all controls on the appliance before disconnecting
or connecting the power cord.
• Always replace the fuse in the plug with a 13amp fuse. Always protect the
power cable from heat.
• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat.
• Care should be taken to arrange the extension cord as it can be a trip hazard.
• Always switch o and unplug the appliance before performing maintenance
or troubleshooting checks.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.
Contents
Included with
your machine
Dehumidier
Let us know what you think @VaxUK
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support
Drainage hose
Model Number DCS2V1MP
Power Input Please refer to rating label
Rated Frequency 50Hz
Input Voltage 220-240V
Tank Capacity 5.5l
Moisture removal 16 Litres/Day
Weight 12.6kg
Model Number DCS3V1HP
Power Input Please refer to rating label
Rated Frequency 50Hz
Input Voltage 220-240V
Tank Capacity 5.5l
Moisture removal 20 Litres/Day
Weight 12.6kg
Technical Specication
Subject to technical change without notice.
Adjustable air
outlet cover
Handle
Water tank
release handle
Air inlet grill/
lter cover
Drainage port
Water tank
(hidden)
Air outlet grill
LED indicator
light
Castor wheels
Control panel
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
What to do if it goes wrong
Getting in touch
Getting to know your machine
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Before you begin
For best performance position the appliance a safe distance
away from walls, furniture and clothing with sucient spacing
as shown above, preferably a hallway or landing with the
internal doors open.
Plug the dehumidier into the mains. The appliance will produce a 2
second audio bleep conrming there is power to the appliance. Press
the on/o button on the control panel to switch the appliance on.
The fan will activate and the Led light on the front of the appliance
will illuminate.
Using the mode/programme button select one of the four
programme options.
Adequate ventilation
such as leaving
all internal doors
open, will allow
the dehumidier to
provide best coverage
around the
home.
IMPORTANT: Remove all packaging covering the appliance. Make sure the water tank and lters are in place and
correctly tted. Stand the appliance upright on a stable, at surface away from sources of heat or open windows.
Never block the air grills, keep the air grills free from any obstruction. Never position the dehumidier under
washing to prevent water dripping onto the appliance.
IMPORTANT: Care should always be taken when using a dehumidier in a new build home or if any internal
plaster renovation has been carried out within the last 6 months.
We recommend using the appliance with the humidity dial set to high and gradually adjusted over a period
of weeks to prevent excess over-drying. Vax cannot be held responsible for any building damage as a result
of improper use. Guidance should always be taken from you home builder.
30cm or more
20cm
or more
20cm
or more
20cm
or more
10cm
or more
TIP
Using your machineGetting started
Using the control panel
The LED lights will illuminate over the function names when selected
Timer
1hr delay o increments up until
a maximum of 24hrs.
Tank Full
Indicates tank
is full/removed.
Timer
Indicates time delay
is active.
Clothes Drying Mode
Operates the fan on high speed
and turns on compressor – ignore
users humidity setting so it can
dry clothes within the room The
product will only operate for a
maximum of four hours to prevent
over drying and potential property
damage.
Fan Only Mode
Operates the fan on high speed
– no compressor or extraction.
Ideal for summer / winter
months to help circulate air
in a room.
Night Mode
The user sets their humidity level
for night. The product reduces to
low fan, LED’s power o and the
audio function turns o so not to
disturb the user during the night if
the tank is full.
Only operation and Night Mode LED
will remain lit on the display.
Daily Mode
Allows the user to pre-set the room
humidity level – between 30 – 80%.
Digital display
Displays current humidity,
set humidity and time delay.
Allows user to adjust humidity/
time delay hours.
On/OProgram
Allows one of the
4 programs to be
selected.
On/O Indicator
IMPORTANT: The control panel is touch sensitive, lightly press the
controls. When the machine is activated the digital humidity reading of the
room will be displayed.
Using the Adjustable air outlet cover
The LED lights will illuminate over the function when selected
The air outlet cover should always be open when
the appliance is in use. Adjust the cover manually
to direct the air to the preferred setting and to
prevent the least disruption to the surroundings.
Important: When the dehumidier is rst used it will produce a signicant amount of water and the tank will need
emptying more frequently. As the room becomes drier the dehumidier collects less water and the tank takes
longer to ll.
Always switch the appliance o and unplug from the mains when removing or retting the water tank or lter and
before carrying out any maintenance or troubleshooting checks.
Using the hose for continuous drainage (optional)
Using the release handles pull either side
of the water tank and remove the water
tank from the back of the appliance .
The water tank must remain tted to the appliance when using the hose for continuous drainage. Using the drainage hose will allow
continuous emptying of the dehumidier. Water will be directed out through the hose and will not collect within the internal water tank.
The hose must be lower than the drainage port allowing the water to ow and prevent any ooding. Connect the hose to oor drain or
stand pipe making sure it is correctly secured.
Attach the drainage hose to the
water outlet. (Located behind the
drainage port).
Ret the water tank making sure the
hose lines up with the drainage port and
does not become trapped.
Using your machine Using your machine
Using the Dehumidier
Using the control panel and setting the humidity
Using the Control panel and setting the time delay
Smart Air Sensor technology
IMPORTANT:
The control panel is touch sensitive, lightly press the controls. When the machine is activated,
the digital humidity reading of the room will be displayed.
Programme Options
Using the mode button choose one of the following four options:
Fan – This programme operates the dehumidier in fan only mode (no moisture extraction, ideal for summer months when dehumidication
is not required), to circulate air in the home or a room.
Clothes dry – This programme ignores room humidity levels and any settings selected and operates full extraction on high fan mode.
This programme is best suited when drying clothes ideally in a small/medium sized room. This programme will run for 4 hours and will
automatically switch o the appliance.
Daily – This programme is specically for dehumidication within the home. The user can automatically set humidity target from
80 - 30% and will regulate to that level. The product will automatically adjust between high and low fan speed depending on the target
humidity and actual humidity level dierence.
Night – This programme is specically for dehumidication at night. The user can automatically set the humidity target from 80 – 30%
however the dehumidier will only operate in low fan for night time use. The LED light will switch o and the audio tank full will be
disabled, so as not to disturb you during the night.
The target humidity levels can be adjusted on the daily and night programs which are automatic.
The humidity can be adjusted from 80 – 30% in 5% increments. Once the room humidity meets the set level, the appliance will
automatically switch o and turn back on when needed to maintain this level. (The LED light on the front panel and the display lights
on the control panel will remain on continuously).
To make this adjustment, use the and buttons. The display wish ash to indicate this target value and will then revert back
to actual room humidity.
The timer function allows you to switch the appliance o after a set number of hours. If this is not selected the appliance will run
in continuous mode (with the exclusion of clothes drying).
Press the timer button. The display panel will then display ’00’. Using the and buttons select the required amount of time
up to a maximum of 24 hours. (The clothes drying mode can only be timed to a maximum of 12 hours). After 3 seconds of setting
the timer the display panel will revert back to displaying the humidity of the room.
To display the remaining timed hours, press the timer button and the remaining hours will then appear on the display.
Your Vax dehumidier automatically monitors the humidity in the room and adjusts the extraction rate accordingly, as well as changing the
indicator light on the front of the machine.
Blue light – indicates when the room humidity is less than 50%
Green light – indicates when the room humidity is at an ideal humidity setting of between 50% - 70%
Red light – indicates when the room humidity is very high, greater than 70%
Red ashing light means the water tank is full and will need to be emptied out.
Emptying the water tank
With the water tank removed from the
appliance, gently pull one side of the
water tank handle to detach from the
water tank cover.
Pull and remove the other side of the
handle from the cover.
Lift and remove the cover from the
water tank.
Rinse the tank under water and wipe
dry with a clean cloth.
Ret the water tank cover and the
handle to secure cover into place.
IMPORTANT: Do not leave water stored in the water tank between uses.
Always switch the appliance o and unplug from the mains when removing or retting the water tank or lter,
and before carrying out any maintenance or troubleshooting checks.
IMPORTANT: Do not attempt to remove the oat from inside the tank.
When the water tank is full or incorrectly tted, the LED light on the front of the appliance will ash. The appliance
will operate for several minutes and then shut down. The LED light will continue to ash.
Emptying the water tank
Using the release handles pull either
side of the water tank and remove
the water tank from the back of the
appliance.
Carry the water tank carefully by the
handle. The water tank cover is not
detachable.
Empty the water tank over a sink and
rinse tank. Wipe the outside of the tank
with a clean dry cloth and ret tank.
Taking care of your machine Taking care of your machine
Note: For optimal performance regularly clean and maintain the lter.
If the appliance will not be used for a long period of time:
• Unplug from the mains
• Empty the water tank and allow to dry before retting
• Clean the lter
• Store the dehumidier in the upright position away from direct sunlight, at room temperature and where the
appliance cannot freeze.
Cleaning the dehumidier
Storage
Keep all grills/openings clear of dust
and debris.
Wipe the dehumidier with a clean
dry cloth.
IMPORTANT: The lter should be cleaned every two weeks and replaced every 6 months dependant upon use.
Do not use the dehumidier without the lter being correctly tted and in place.
The appliance is intended for household use only and should not be used in high dusty environments such as during
building or renovation work.
Note: For optimal performance regularly clean and maintain the lter.
Cleaning the lter
Lift the air inlet grill/lter cover located
on the back of the dehumidier.
Separate the lter and cover. Use a vacuum cleaner with a soft
dusting brush attached or tap the lter
over a bin to remove dust.
Wash the lter under running water
(40 degrees max) Leave for 24 hours
or until fully dry before retting.
Never place in a dishwasher to clean.
Taking care of your machine Taking care of your machine
†
†
Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before cal ling.
The plug may not be fully pushed into the electrical socket.
Check the fuse in the plug if this needs replacing, always replace with a 13amp
British fuse.
Timer may have nished, re-set the timer. Go to ‘Using your machine’.
The water tank is full. Go to ‘Taking care of my machine’.
The machine has not been positioned correctly, place the machine on a at, stable,
solid surface. Go to ‘Getting started’.
The drainage hose has not been correctly tted. Go to ‘Using your machine’.
The machine has been moved or tilted with water in the water tank. Remove water
tank and empty. Go to ‘Taking Care of your machine’.
The water tank is full. Go to ‘Taking Care of your machine’.
The water tank is incorrectly tted. Ret the water tank.
SolutionProblem
Why does my
dehumidier
have no power?
Why is water leaking
from my dehumidier?
Why are the LED lights
ashing red on the
control panel?
Getting in touchWhat to do if it goes wrong
GET IN TOUCH
0330 026 8455 VaxVacuumsinfo@vax.co.uk vax.co.uk @VaxUK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
DCS2V1MP and DCS3V1HP are manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage
Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
© 2016 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.
Loading...