www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 6061248
instruction manual
Carpet washer
Vax model number:
V-024U
UL
T
RA
SOLUTION
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 1
2
parts overview
Fig.1/1
www.vax.co.uk
1. Diagram
V-024U
1 Handle
2 Clean solution reservoir latch
3 Clean solution reservoir
4 Dirty water tank latch
5 Dirty water tank handle
6 Floating brushbar
7 Dirty water tank
8 Dirty water tank lid
9 Power switch
10 Handle screw
11 Power cord
12 Carrying handle
13 Quick cord release
14 Handle release pedal
15 Cord hook
16 Cord clip
17 Solution release trigger
18 Vax Ultra Solution
1
17
9
10
3
13
15
14
5
7
2
1
6
11
12
18
4
8
6
UL
T
RA
SOLUTION
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 2
3
V
ax Careline 0870 606 1248
safety information
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Nottobe used as a toy. Children should besupervisedto
ensure that they do not play with the appliance.
4. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack ofexperience and knowledge,
unless they have been given supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
5. Use only as described in this manual.
6. Do not use with a damaged cord or plug. If the supply
cord and/or plug is damaged, they must be replaced
by the manufacturer, a Vax Service Agent or similarly
qualified persons in order to avoid hazard.
7. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
8. Do not unplug by pulling on the cord.
9. Do not handle the plug or carpet washer with wet
hands.
10. Do not put any objects into openings or operate with
openings blocked, keep them free of anything that
may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
12. Do not use the carpet washer on any glowing,
burning or smoking particles.
13. Do not use without the solution tank and dirty water
tank in place.
14. Do not use the vacuum without the dust bag in place.
15. Turn off all controls before unplugging.
16. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they may
be present.
17. Keep the unit on the floor.
18. Do not use an extension cord.
19. Do not attempt to remove blockages with sharp
objects as they may cause damage.
20. Store indoors put away after use to prevent tripping
accidents.
21. Using improper voltage may result in damage to the
motor and possible injury to the user. The correct
voltage is listed on the rating label.
22. A hazard may occur if the carpet washer runs over
the power supply cord.
23. To prevent dirty water from running into motor, do
not hold the appliance upside-down or lay on its side.
Use appliance in normal vacuuming position.
24. Use extra care when cleaning on stairs.
25. Do not carry appliance while motor is running.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
NOTE: The unit must be unplugged from the mains
socket outlet after use, and before cleaning or
maintaining the unit.
IMPORTANT: This unit is not intended for
commercial use.
PLEASE KEEP THESE INSTRUCTIONS
FOR FURTHER USE.
!
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 3
www.vax.co.uk
4
assembly/ operation
3. Assembly
Putting your cleaner together
Stand the base in the upright position. Assemble the mid
section onto the base, taking care not to trap internal
mains wire (Fig 3/1).
Insert the three nuts into the recesses located on the left
and right sides of the base and into the recess located in
the middle of the back of the base.
While holding the nuts in place insert screws through the
front of the mid section and tighten (Fig 3/2).
NOTE: Phillips screwdriver required
Slide the upper handle down onto the unit. Insert nut into
the recess in the back of the upper handle. While holding
the nut in place insert the screw through the front of the
upper handle and tighten.
Run the mains wire above the upper cord hook and
secure with the cord clip (Fig 3/3).
4. Operation
IMPORTANT: Turn off when emptying and filling
the reservoir.
Grasp the solution reservoir under the handle and press
the handle release lever upward (Fig 4/1).
Tilt the solution reservoir away from the cleaner and
remove (Fig 4/2).
Unscrew the filler/ measure cap from the rear of the
solution reservoir (Fig 4/3).
Fill the bottle cap or measure cap 4 times with Vax Ultra
Solution and pour into the reservoir (Fig 4/4).
Fig.3/1
Fig.4/1
Fig.4/2
Fig.3/2
Fig.4/3
Fig.4/5
Fig.4/6
Fig.3/3
!
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 4
5
V
ax Careline 0870 606 1248
operation
IMPORTANT: Maximum water temperature 50°C.
Fill the remaining space in the solution reservoir with
warm tap water. Replace the measuring cap (Fig 4/5).
NOTE: use only Vax Ultra Solution, using other
cleaning solutions may cause excessive foaming.
This may cause the float to shut of the cleaner
prematurely. Using other cleaning solutions will
invalidate your warranty.
Place the bottom of the solution reservoir into the
cleaner and push into place. There will be an audible click
when the reservoir is in the correct position (Fig 4/6).
Plug the cord into a mains electricity socket.
Turn the power switch on (Fig 4/7).
The switch is located on the front of the cleaner, above
the solution reservoir.
The power switch controls the vacuum motor.Press on
the handle release pedal and pull the cleaner back into a
reclined position (Fig 4/8).
IMPORTANT: Never leave the cleaner
unattended with the power on.
NOTE: Vacuum carpets thoroughly with dry vacuum
cleaner before washing.
Whilst depressing solution spray trigger, push carpet
washer in a forwards motion. Release trigger and pull unit
backwards in same path to remove dirty water and
solution from the carpet. (Fig 4/9).
Repeat if necessary, when the dirty water reaches the
max fill line on the dirty water tank empty the tank.
Fig.4/4
Fig.4/5
Fig.4/6
Fig.4/8
Fig.4/7
Fig.4/9
!
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 5
www.vax.co.uk
6
operation
Emptying the dirty water tank
NOTE: The float in your Rapide Classic is the blue part
in the dirty water tank lid, it will shut off the suction
when the dirty water tank is full. For best results use
a smooth steady motion keeping the nozzle flat
against the carpet.
Tipping the cleaner and breaking the seal of the
nozzle against the carpet will cause the float to rise
cutting off suction. Once the float is activated, empty
the dirty water tank. If the tank does not appear full
turn off the power switch and wait for the float to
settle. For best results use only Vax Ultra Solution.
You will hear a distinct change in the noise coming from
your cleaner when the tank is full and needs emptying.
IMPORTANT: Unplug your cleaner before
emptying the dirty water tank.
Grasp the top of the dirty water tank handle and press
the release latch (Fig 4/10).
Grasp the handle and pull up out of the base, take care to
ensure that no dirty water leaks from the front (Fig4/11).
Remove dirty water tank lid (Fig 4/12).
To empty the water tank grasp the handle with one hand
and nozzle with the other and empty into the sink
(Fig 4/13).
Cleaning the dirty water tank
Rinse the dirty water tank and filter thoroughly, with
warm water (Fig 4/14).
You should allow them to dry fully before replacing them
on your cleaner to prevent mildew.
Do not use any chemicals in the cleaning process.
Replacing the dirty water tank
Lift the front of the carpet cleaner base off the carpet
with one hand (Fig 4/15).
Fig.4/11
Fig.4/14
Fig.4/12
Fig.4/13
Fig.4/10
Fig.4/1
Fig.4/1
Fig.4/1
!
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 6
7
V
ax Careline 0870 606 1248
operation/ maintenance
Emptying the dirty water tank
Grasp the handle and hook the front of the dirty water
cleaner into the base, making sure that the front of the
dirty water tank is resting on the base.
The dirty water tank has three tabs on the underside
which MUST latch on to the underside of the base of the
cleaner. The base must be lifted so that the nozzle is
flush with the base of the cleaner.
Failure to install the dirty water tank correctly will result
in poor dirty water pick up (Fig 4/16).
While making sure the dirty water tank is resting on the
base, place the rear of the tank into the base of the
cleaner, push down on the handle until it latches.
Empty and rinse clean water tank after use (Fig 4/17).
5. Maintenance
Brush removal and replacement
NOTE: Phillips screwdriver required
NOTE: The plug must be removed from socket outlet
before cleaning or maintaining the appliance.
Remove the water tank switch off and unplug carpet
washer.
Flip the cleaner on its side to expose the nozzle base
(Fig 5/1).
To remove the brush access cover, use a Phillips
screwdriver to remove the two screws (Fig 5/2).
Lift out the floating brush bar (Fig 5/3).
Fig.4/15
Fig.4/16
Fig.4/17
Fig.5/1
Fig.5/2
Fig.5/3
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 7
www.vax.co.uk
8
maintenance/ troubleshooting
Replace floating brushbar (Fig 5/4).
Replace the brush access cover by inserting the end
furthest from the brush first. Then replace the front end
before securing in place with the two screws (Fig 5/5).
6. Troubleshooting
WARNING: To reduce the risk of personal injury,
unplug the vacuum cleaner before performing
maintenance or troubleshooting checks.
PROBLEM: The cleaner won't run.
Cause: Not properly plugged into electrical outlet.
Solution: Plug in firmly.
Cause: No electricity in electrical outlet.
Solution: Check fuse or breaker.
Cause: ON/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won’t pick up/loss of suction.
Cause: Dirty water tank is full.
Solution: Switch off and unplug cleaner. Empty dirty
water tank as shown in Section 4.
Cause: Dirty water tank not installed correctly.
Solution: Refer to page 9 for fitting information.
Cause: Obstruction in hose/nozzle.
Solution: Remove hose and clear obstruction.
Cause: Broken or worn belt.
Solution: Replace the belt. See page 10.
Cause: Brushbar is worn.
Solution: Replace the brush bar. See page 10.
PROBLEM: Liquid escaping from the carpet washer.
Cause: Dirty water tank is full.
Solution: Switch off and unplug cleaner. Empty dirty
water tank as shown in Section 4.
Cause: Dirty water tank not installed correctly.
Solution: Refer to page 9 for fitting information.
Cause: Solution tank not installed correctly.
Solution: Make sure the tank is securely locked in place
PROBLEM: Clean solution won’t dispense.
Cause: Solution tank not installed correctly.
Solution: Make sure the tank is securely locked in place.
Cause: Solution tank empty.
Solution: Refill tank.Refer to page 6 for instructions.
!
Fig.5/4
Fig.5/5
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 8
9
V
ax Careline 0870 606 1248
uk service & help/ technical specification
7. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 8.00am to 6.00pm
Saturday-Sunday 9.00am to 5.00pm
An answerphone is available outside of these hours. Any
queries or concerns about using the Vax, call the Vax
Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
8. Technical Specification
Voltage: 220-240V ~50Hz
Wattage: 600 W
Capacity: Clean water tank - 2.0 litres
Dirty water tank - 3.5 litres
Cord length: 7.5 metres
Weight: 5.75kg
Subject to technical change without notice.
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 9
www.vax.co.uk
10
This page has been left intentionally blank.
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 10
11
V
ax Careline 0870 606 1248
This page has been left intentionally blank.
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 11
---
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
Vax V-024U is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Wasteelectrical products should not be disposed of with household waste.Please recycle where
facilities exist. Check with your Local Authority or retailer for recyclingadvice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
V-024U User Guide v2.qxd:V-024U User Guide 12/3/08 08:47 Page 12
Loading...