Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using the
carpet washer. Always fully extend
the mains cable before use.
www.vax.co.uk
UPRIGHT CARPET WASHER
Vax Model Number: V-028M/CCW-501
UPRIGHT CARPET WASHER
Vax Model Number: V-028/CCW-502
UPRIGHT
CARPET WASHER
Vax Model Number: V-028MPT
UPRIGHT CARPET WASHER
Vax Model Number: V-028PET
UPRIGHT CARPET WASHER
Vax Model Number: V
-028PT
Vax V-028 Range.qxd 27/4/07 13:26 Page 1
1. Diagram
P
arts Overview
Attachments
(Model: V-028/V-028MPT/V-028PT/
V-028PET only)
24. Hose wrap
25. Solution tube
26. Upholstery/stair hose adaptor
27. Upholstery/stair hose
28. Upholstery/stair attachment
29. Solution spray trigger
30.
8x Scr
ews
(Model: V
-028/V
-028PT/
V
-028PET only)
28. 5x Screws
(Model: V-028M/V-028MPT only)
31.
Pr
e-tr
eatment wand
(Model: V
-028MPT/V
-028PT only)
32. Powered wash brush
(Model: V-028PET only)
7
8
9
10
11
12
14
15
29
30
28
26
25
27
16
17
18
19
24
13
6
2
3
4
5
1
2
Fig.1/1
Fig.1/4
Fig.1/5
Fig.1/3
Fig.1/2
p
re
treatment
pre-treatment
carpetsolution
solutiondeprélavage
pourtapisetmoquettes
teppichvorwaschspray
tapitreinigerspray
AAA
ANTI
ALLER GE N
A
DDITI VE
20
1. Handle
2. Clean water tank latch
3. Clean water tank
4. Dirty water tank latch
5. Dirty water tank handle
6. Brushbar
7. Dirty water tank
8. Dirty water tank door
9. Dirty water tank lid
10. Solution tube clip
11. Power cord
12. Lower cord clip
13. Lower cord wrap with
quick cord release
14. Power on/off pedal
15. Solution tube port
16. Handle release pedal
17. Tool caddy
18. Carry handle
19. Cord wrap
20. Vax AAA Carpet Cleaner
21. Pre-treatment solution (Model:
V-028MPT/V-028PT only)
22. Vax “For Pets” AAA carpet
cleaner (V-028PET only)
23. Vax Spot and Stain Remover
(V-028PET only)
Fig.1/6 Fig.1/7
31 32
s
pot&stain remover
forhomeswith
21 22 23
Vax V-028 Range.qxd 27/4/07 13:26 Page 2
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the carpet washer, basic safety precautions
should always be observed, including the following.
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. If the
supply cord and/or plug is damaged, they must be
replaced by the manufacturer, a Vax Service Agent
or similarly qualified persons in order to avoid hazard.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with
hot or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
10. Keep hair, loose clothing fingers and all parts of
the body away from openings and moving parts.
11. Do not use the carpet washer on any glowing,
burning or smoking particles.
12. Do not use without the solution tank and dirty
water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the carpet washer on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent
tripping accidents.
19. Using improper voltage may result in damage
to the motor and possible injury to the user
.
The correct voltage is listed on the rating label.
20. A hazard may occur if the carpet washer runs over
the power supply cord.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
NOTE: If the supply cord is damaged, it must be
replaced by the manufactur
er, a Vax service agent or
similarly qualified persons in order to avoid hazard.
S
afety Information/Use & Function
3. Use & Function
Assembling the carpet washer
Fig.3/2: Insert 4 lower handle/tool caddy scr
ews (as
shown) and tighten until secur
e.
BACK VIEW
BASE
POCKETS
TABS
MID-SECTION
Fig.3/1
Fig.3/2
CORD
3
NOTE: The carpet washer must be unplugged from
the mains socket outlet after use, and before cleaning
or maintaining the carpet washer.
IMPORTANT: This carpet washer is not intended for
commercial use.
Fig.3/1: Stand base in upright position. Push mid-section
onto base by aligning tabs on inside of mid-section with
the pockets on the base as shown in Fig.3/1.
Vax V-028 Range.qxd 27/4/07 13:26 Page 3
Fig.3/4: Insert the upper handle screw (as shown) and
tighten until secure.
NOTE: Make sure the power cord is out of the way to
avoid pinching.
BACK VIEW
Note: model
V-028M does
not have hose
wrap shown.
UPPER HANDLE
4
U
se & Function/Tool Caddy Assembly/Cord Storage
Fig.3/5
Fig.3/7
Fig.3/6
Fig.3/4
Caddy Assembly
(Model: V-028/V-028PT/V-028PET only)
Align tool caddy with screw holes on mid-section
and base.
Insert the three (3) tool caddy screws (as shown) and
tighten until secure.
Cord Storage
Wrap cord around
upper and lower
cord wraps as
shown in Fig.3/7.
Clip plug to cord to
secure for storage.
Upper Cord
Wrap
Lower Cor
d
Wrap with
Quick Cord
Release
Fig.3/3: Slide upper handle down onto unit.
Fig.3/3
Vax V-028 Range.qxd 27/4/07 13:26 Page 4
Tool Storage/Preparing the Carpet
Fig.3/8
Fig.3/9
Fig.3/10
Fig.3/11
Fig.3/12
Place Upholstery/Stair hose adaptor, Upholstery/Stair
hose, and the Upholstery/Stair attachment into their
storing locations.
Slide the adaptor end of hose into the left clip
on tool caddy.
U
pholstery/
S
tair hose
Upholstery/Stair
hose attachment
Upholstery/Stair
h
ose adaptor
Left clip On
Tool caddy
Adaptor end
of hose
Hose
clips
No 2
Run hose from the tool caddy to the upper hose
wrap and press into hose clip No.1 (Fig.3/10). Continue
wrapping hose clockwise, aligning hose into groove on
the bottom hose clip (Fig.3/11). Wrap hose back to the
upper hose wrap and press into hose clip No.2
(Fig.3/10). Slide upholstery tool attachment handle into
the right clip of the tool caddy (Fig.3/12).
4. Preparing the Carpet
IMPORTANT: DO NOT USE THE CARPET WASHER
AS A DRY VACUUM.
1. Vacuum carpet thoroughly. Use a vacuum cleaner
with a revolving brushbar for best results.
2. Remove as much furniture from the room as
possible. If unable to remove the furniture, place
plastic or foil under and around the legs until the
carpet has dried completely.
HELPFUL HINTS FOR CLEANING CARPET:
1. Only use Vax AAA Carpet Cleaner with this carpet
washer.
2. Do not oversaturate carpet with cleaning solution
while using the carpet washer.
3. For heavily soiled areas, additional applications may
be necessary.
4. Allow plenty of time to dry carpet thoroughly.
5. Wipe cleaning solution from woodwork and wood
to prevent any damage.
6. Try not to walk on carpet until it is completely dry.
7. After carpet is thoroughly dry, vacuum the carpet
using a vacuum cleaner with a revolving brushbar.
8. Before cleaning, determine where to start and end,
making sure not to walk over previously cleaned
areas.
CHECK FOR COLOUR FASTNESS:
Before cleaning carpet, test for colour fastness.
Dampen a white cloth with solution. Test a small area
in a closet. Gently rub the cloth over the area. Check
each colour for colour bleeding. If the cloth remains
clean, it should be safe to clean the carpet.
AFTER CLEANING:
•
Allow carpet to dry completely
. T
ry not to walk on the
carpet until it is dry.
•
If it is necessary to walk on the carpet, place white
towels on the areas to be walked on.
• If the carpet is not dry and the furniture must be
placed back in the room, use plastic or foil under the
furniture to prevent staining the carpet.
•
Thor
oughly clean the dirty water tank with warm
(max 40
o
C) tap water
.
Bottom
hose clip
No 1
Upholstery
tool
attachment
handle
Right clip
on Tool
caddy
Tool Storage
(Model: V-028/V-028PT/V-028PET only)
5
Vax V-028 Range.qxd 27/4/07 13:26 Page 5
P
re-treating your Carpet
6
5. Pre-treating your Carpet
(Model: V-028MPT/V-028PT only)
Grasp the clean water tank under the handle while
pressing the clean water tank latch. Tilt the clean
water tank away from the carpet washer and remove.
Unscrew the measuring cap from the back of the
clean water tank.
C
lean water
t
ank handle
Clean water
t
ank latch
Fig.5/1
Fig.5/2
Fig.5/3
Fill the remainder of the clean water tank with warm
(max 40oC) tap water. Replace the cap.
Place the bottom of the clean water tank into the
carpet washer and rotate top into position until the
clean water tank latch snaps into place.
Attach the pr
e-tr
eatment wand to the water supply
port and pr
ess firmly until it locks into place.
Fig.5/4
Fig.5/6
Fig.5/5
BACK
VIEW
Fill the measuring cap with the pr
e-treatment solution
(approximately 3 capfuls per litre of clean water).
Pour into the clean water tank.
Vax V-028 Range.qxd 27/4/07 13:26 Page 6
7
P
re-treating your Carpet / How to Operate
Fig.5/7
To pre-treat your carpet, step on the power on/off pedal
to turn the cleaner on.
Using the wand and the trigger, apply the pre-treatment
solution to your carpets. Turning the spray nozzle
clockwise or anti-clockwise will alter the spray pattern.
Fig.5/8
Fig.5/9
Releasing the trigger will stop the solution flow.
The treated areas should be left for 10 to 15 minutes.
For heavy stains, mild agitation may be used.
Note: Do not over wet carpets.
Note: Once your carpets have been pre-treated,
rinse the clean water tank and clean your carpets with
Vax AAA Carpet Cleaner as directed.
6. How to Operate
Grasp clean water tank under handle while pressing
clean water tank latch. Tilt clean water tank away from
cleaner and remove.
Unscrew measuring cap from back side of clean water
tank.
C
lean water
tank handle
C
lean water
t
ank latch
Fig.6/1
Fig.6/2
Fig.6/3
Vax V-028 Range.qxd 27/4/07 13:26 Page 7
H
ow to Operate/Carpet Cleaning
8
Fill measuring cap with solution (approximately
4 capfuls). Pour into clean water tank.
NOTE: Use only Vax AAA Carpet Cleaner solution.
Using other cleaning solutions may cause excess
foaming. Excessive foam will cause the float to shut off
the carpet washer prematurely. Using other solutions
will void the warranty.
Fill remainder of clean water tank with warm (max
40ºC) tap water. Replace cap.
7. Carpet Cleaning
Place bottom of clean water tank into carpet washer
and r
otate top into position until the clean water tank
Latch snaps into place.
Fig.7/1
Fig.7/3
Fig.7/2
Plug cord into electrical socket. Step on the power on/off
pedal to turn cleaner on.
NOTE: Never leave unit unattended with power on. Turn
off when emptying and filling tanks. Do not oversaturate
the carpet.
Step onto handle release pedal to put into cleaning
position.
Fig.7/4
Fig.7/5
While depr
essing solution spray trigger, pull carpet
washer in backwar
d motion. Release trigger and push
unit forwar
d in same path to remove dirty water and
solution fr
om carpet. (For heavily soiled areas, repeat
if necessary).
Vax V-028 Range.qxd 27/4/07 13:26 Page 8
9
Fig.8/1
IMPORTANT: For best cleaning results use a steady,
moderate, forward and backward motion.
IMPORTANT: If the sound of the motor changes to a
high pitch, this indicates the dirty water tank is full and
must be emptied.
8. Accessories
(Model: V-028/V-028PT/V-028PET only)
Put carpet washer in its upright position, then turn off.
Remove the dirty water tank door from the top of the
dirty water tank.
For cleaning upholstery and stairs
Fig.8/2
C
arpet Cleaning/Accessories
Connect the hose
solution tube into
the fitting on the
lower left side
of handle facing
carpet washer.
Fig.8/4
Step on power on/off pedal to turn cleaner on. While
depressing solution spray trigger, pull attachment in
backward motion. Release trigger and push
attachment forward in the same path to remove dirty
water and solution from upholstery. (For heavily soiled
areas, repeat if necessary.)
NOTE: Do not oversaturate the upholstery.
IMPORTANT: For best cleaning results use steady,
moderate, forward and backward motion. Make sure
upholstery is dry before use.
NOTE: If the dirty water tank door is not replaced,
there will be no suction through the nozzle and the unit
will not operate pr
operly.
Fig.8/5
BACK
VIEW
Upholstery / stair attachment
Fig.8/6
Power Wash Brush usage
(Model: V
-028PET only)
Insert the upholstery/stair
hose adaptor into
the opening on
top of the dirty
water tank.
Fig.8/3
Vax V-028 Range.qxd 27/4/07 13:26 Page 9
10
A
ccessories/Filters
The carpet washer is equipped with a shut off valve
within the dirty water tank. When the dirty water tank
becomes full, the float will rise, shutting off the air flow
through the nozzle.
NOTE: The float in the carpet washer will shut off the
suction when the dirty water tank is full. For best
results, use smooth, steady motion keeping the nozzle
flat against the carpet. Tipping the carpet washer and
breaking the seal of the nozzle and carpet will cause
the float to rise and shut off the suction. Once the float
is activated, empty the dirty water tank. If the dirty
water tank does not appear full, press the Power on/off
pedal and wait for the float to settle and reset. If the
float repeatedly shuts off the suction, empty the dirty
water tank. For best results, use only Vax AAA Carpet
Cleaner. Other solutions may generate excessive foam
which will cause the float to rise prematurely and shut
off the suction. Use 4 (four) capfuls of Vax AAA Carpet
Cleaner per fill up of the clean water tank. A higher
concentration of carpet cleaner may cause excessive
foaming.
NOTE: Ther
e will be a noticeable change in the pitch
of the cleaner. This indicates a need to empty the dirty
water tank.
WARNING: To reduce the risk of injury from moving
parts - unplug befor
e emptying the dirty water tank.
Step on power on/off pedal to turn cleaner on. Press
the button at the back of the Power Wash Brush to
start the rotation of the brushes. To release the flow of
water and solution, press the trigger and then move
the tool in slow circular motions over the desired area.
NOTE: After compressing the trigger there will be a
short time delay before water is dispensed.
NOTE: Although the tool is continually extracting water
from the carpet while switched on, positioning the front
nozzle directly onto the area will allow better recovery
and aid drying.
IMPORTANT: For first use, there may be a 10-15
second delay between depressing the trigger/button
and water being released from the attachments. This is
normal and is not a fault.
Fig.9/1
9. Filters
Emptying and cleaning the dirty water
tank and filter
Grasp top of dirty water tank handle and push latch to
release.
Grasp handle and pull tank out of base.
Fig.9/2
Remove dirty water tank lid.
Fig.9/3
HANDLE
LATCH
Vax V-028 Range.qxd 27/4/07 13:26 Page 10
11
F
ilters
To empty dirty water tank, grasp handle with one hand
and nozzle with the other and empty into sink. To
clean, rinse tank thoroughly with clean water
and let dry.
Fig.9/4
Remove filter from rear of dirty water tank lid.
Fig.9/5
Rinse dirty water tank and filter with warm tap water.
Wipe and let dry thoroughly before storing to prevent
mildew from forming.
NOTE: Do not use any chemicals when cleaning.
Fig.9/6
Push handle down until it latches.
NOTE: Do not store cleaner with solution in reservoir
or dirty water in dirty water tank. Mineral deposits and
mildew can form which will affect the performance of
the carpet washer
.
Fig.9/8
While making sure the front of the dirty water tank is
resting on the base, place the rear of the tank into the
base of the cleaner.
Replacing dirty water tank in base
of carpet washer
Fig.9/7
Vax V-028 Range.qxd 27/4/07 13:26 Page 11
11. Troubleshooting
WARNING: TO REDUCE RISK OF PERSONAL
INJURY, UNPLUG CARPET WASHER BEFORE
SERVICING
PROBLEM: Carpet washer won’t pickup or low suction
Cause: The dirty water tank door is not installed.
Solution: Insert the dirty water tank door.
Cause: The dirty water tank door is not installed
correctly.
Solution: Review placing dirty water tank in base of
carpet washer.
Cause: The dirty water tank is full.
Solution: Empty the dirty water tank.
Cause: The dirty water passage clogged.
Solution: Clean the dirty water tank.
PROBLEM: Water escaping from carpet
washer
Cause: The dirty water tank is full.
Solution: Empty the dirty water tank.
Cause: The dirty water tank is not installed correctly.
Solution: Review placing dirty water tank in base of
cleaner.
Cause: The clean water tank is not installed properly.
Solution: Review clean water tank installation.
PROBLEM: Carpet washer won’t
dispense solution
Cause: The clean water tank is not installed properly.
Solution: Review How to Operate.
Cause: The carpet washer needs a service.
Solution: Take it to service center or contact Vax
Careline.
PROBLEM: Carpet washer attachments
won’t pick up (Vax Model V-028 only)
Cause: The hose is clogged.
Solution: Remove the hose and tools; remove
obstruction.
Cause: The dirty water tank is full.
Solution: Empty the dirty water tank.
PROBLEM: Carpet washer attachments
won’t spray (Vax Model V-028 only)
Cause: The solution tube is not connected pr
operly
.
Solution: Connect the solution tube properly.
S
torage/Troubleshooting
12
10. Storage
Transporting & storing carpet washer
Fig.9/1 Put handle in upright locked position.
Turn unit off. Store cord and above floor cleaning
attachments if used.
Fig.9/2 Tilt unit back on rear wheels and push
forward.
NOTE: The unit can also be transported between
rooms or floors using the carry handle.
BEFORE STORING CARPET WASHER:
1.
Empty and rinse clean water tank and dirty
water tank.
2. Replace empty clean water tank and dirty water
tank.
3. Ensure that brushes and underside of unit are fully
dry prior to storing on a carpeted or
wood surface.
NOTE: Do not store unit with a full clean water tank or
dirty water tank.
DO NOT TRANSPORT THE CARPET WASHER
WITH EITHER THE CLEAN WATER TANK OR
DIRTY WATER TANK FULL.
Fig.10/1
Fig.9/2
Vax V-028 Range.qxd 27/4/07 13:26 Page 12
13
UK Service & Help/Technical Specification
13. Technical Specification
Power supply: 220-240/50Hz
Motor power: 900W
Clean water tank volume: 4 litres
Dirty water tank volume: 2.0 litres
Filter system: Foam block
Cord length: 7.5m
Weight: 8.9kg
Subject to technical change
without notice.
12. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone is available out of these hours.
Any queries or concerns about using the Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
Vax V-028 Range.qxd 27/4/07 13:26 Page 13
14
This page is intentionally blank
Vax V-028 Range.qxd 27/4/07 13:26 Page 14
15
This page is intentionally blank
Vax V-028 Range.qxd 27/4/07 13:26 Page 15
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the products
V-028/CCW-502, V-028M/CCW-501, V-028MPT, V-028PT, V-028PET
are manufactured in compliance with the following:
Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC
EMC: 89/336/EEC Electr
omagnetic Compatibility Dir
ective, as modified by 93/68/EEC
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: enquiry@vax.co.uk - website: www
.vax.co.uk
Vax V-028 Range.qxd 27/4/07 13:26 Page 16
Loading...