vax.co.uk
U86-AN-Be/U86-AN-Pe/U86-IN2-Pe
Action 602
Let’s get started
Basic safety precautions
Don’ts
8 Don’t use this vacuum cleaner if
it has been dropped, damaged or
left outdoors.
8 Don’t run over the power cord or use
vacuum cleaner if the power cord
or plug is damaged. Please contact
our Customer Care Line on:
0330 026 8455 (Mon-Fri 8.30am
to 6.30pm, Sat 9.00am to 5.00pm).
8 Don’t handle the plug or use the
vacuum cleaner with wet hands.
8 Don’t pull or carry this vacuum
cleaner by the power cord. Don’t use
the power cord as a handle, pull the
power cord around corners, sharp
edges or close a door over the power
cord. Don’t unplug vacuum cleaner
by pulling on the power cord.
8 Don’t vacuum up any ammable
or combustible materials (lighter
uid, petrol, kerosene etc.) or use
the vacuum cleaner in an area with
explosive vapours or liquid.
8 Don’t vacuum up hot coals, cigarette
butts, matches or smoking hot
burning items or use in an area
where there may be harmful uids
(chlorine, bleach, and ammonia
drain cleaner).
Let’s talk safety
This vacuum cleaner is intended
for household use only and NOT for
commercial or industrial use.
• Only use the vacuum cleaner indoors
on dry surfaces and keep the area
your cleaning well lit.
• Keep ngers, hair and loose clothing
from moving parts and openings
whilst using the vacuum cleaner.
• This vacuum cleaner can be used
by children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the vacuum cleaner in a safe
way and understand the hazards
involved. Children shall not play with
the vacuum cleaner. Cleaning and
user maintenance shall not be made
by children without supervision.
• Only Vax recommended tools should
be used with this vacuum cleaner.
Please keep instructions for
further use.
Do’s
3 Turn o all controls on the vacuum
cleaner before disconnecting or
connecting the power cord.
3 Always make sure lters are in place
before use.
3 Always switch o the
vacuum cleaner before
disconnecting or connecting
the hose and accessories.
3 Keep all openings clear and free
from debris as this may aect the
airow/suction.
3 Always replace the fuse in the plug
with a British 13amp fuse. Always
protect the power cable from heated
surfaces and open ames.
3 Take extra care when positioning
and using the vacuum cleaner
on the stairs.
3 Use only CE approved 13amp
extension cords, non-approved
extension cords may overheat.
Care should be taken to
arrange the extension cord
as it can be a trip hazard.
3 Store your vacuum cleaner in a cool,
dry area. If lters have been cleaned
as per user guide instructions
ensure they are thoroughly dry
before storing away.
Don’ts
8 Don’t attempt to remove blockages
with sharp objects as this may cause
damage to your vacuum cleaner.
8 Don’t vacuum up hard or sharp
objects such as glass, nails, screws
or coins etc.
8 Don’t use the vacuum cleaner with
incorrect voltage as this may result
in damage or injury to the user.
The correct voltage is listed on the
ratings label.
Let’s talk safety
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm, Saturday 9.00am to 5.00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can also be found online at: vax.co.uk/support
Let us know what you think @VaxUK
Thank you for buying this Action 602.
Taking care of your carpets
The Action 602 is designed to make washing carpets regularly, as eective and ecient
as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets will ensure they keep their appearance for longer and smell fresh and
clean. You’ve chosen the carpets for your home for a reason and Vax will help you take good care
of them.
Taking care of your Action 602
Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets.
Contents
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
What to do if it goes wrong
Getting in touch
Accessories
Notes
Action 602
Included with
your machine
Action 602 Pet
+
TurboTool
Reach extension hose 2.2m
Reach extension hose 1.5m
2 in 1 dusting/upholstery
& crevice tool
Extension tube
Hard oor tool
Action 602 Reach
+
Initial Setup for normal operation
1. Use the base accessories.
a. Shortest hose.
b. Extension tube set to shortest practicable length.
2. Clean lters installed.
3. Dust receptacle empty.
4. All Bleeds must be closed.
5. Variable Power set to Maximum.
6. Floor heads/tools set to Carpet Mode for carpet cleaning.
7. Mechanical Agitation turned ON for carpet cleaning.
8. Floor heads/tools set to Hard Floor Mode for hard oor cleaning.
9. Mechanical Agitation turned OFF for hard oor cleaning.
Extension tube
and crevice
Handle release button
Dust brush holder
(some models only)
Handle
Turbo tool holder
(some models only)
Carry handle
Dirt container
release button
Separator
Dirt container lid
Dirt container
HEPA pre-motor lter
(hidden)
Dirt release clip
Upper release
cord hook
Hose to machine
connector
Height adjuster dial
Name Action 602
Voltage 220-240V-50Hz
Wattage 900 Air Watts
Cord length 7m
Weight 7.5kg
Technical Specication
Subject to technical change without notice.
Filter Kit (Type 110)
1-1-134394
Belt Kit Type 25
1-1-134411
Turbo Tool Type 6*
1-1-134419
Crevice Tool (Type 16)
1-1-134427
Dusting Brush (Type 10)
1-1-134426
Pro Cleaning kit
(1-1-133326)
Accessories & Consumables
* Selected models only.
To purchase consumables and accessories, please visit vax.co.uk
Hose connector
Hose inlet
On/o button
Getting to know your machine
Assembling your vacuum cleaner
Lift handle up and click
into place.
Slide 2 in 1 Dusting Brush onto
dust brush holder with brushes
facing outwards.
Line up latch on accessory hose,
push until clicks into place.
Line up turbo tool brushes into
turbo tool holder, push into place
until it clicks (some models only).
Push accessory hose into
hose to machine connector.
Push extension tube and
crevice onto holder.
Before you begin cleaning
IMPORTANT: Always switch o the vacuum cleaner before connecting or disconnecting the hose/attachments
or removing and emptying the dirt container.
IMPORTANT: The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does
overheat the thermostat will automatically turn the vacuum cleaner o. If this happens switch the vacuum cleaner o
and unplug from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for blockages.
Allow the vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please wait 24 hours for the
lters to fully dry before putting back into the machine).
Filters require cleaning at least every 3-6 months. If the vacuum cleaner is blocked, switch o and unplug before
removing the blockage.
When the vacuum cleaner is stood in the upright position, or when using the hose and tools the brush bar height adjuster
must be set to the highest setting.
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Getting started
Plug vacuum cleaner into the
mains, switch on. Turn brush
bar height adjuster dial to
desired setting.
Press On/O button to
switch on.
Place foot on oor head
and pull handle to recline.
The accessories can be attached to the extension tube or directly to the hose.
When using accessories on the hose/extension tube raise the height adjuster to the highest setting.
Pull hose out of hose
to machine connector.
Attach accessory
to tube/hose.
Attach accessory hose to
extension hose.
If required attach extension
hose to extension tube.
Using accessories
Choose an accessory.
Using your machine
IMPORTANT: Always switch o and unplug the vacuum cleaner before connecting or disconnecting the hose/
attachments, or removing and emptying the dirt container.
TIP
For best performance use your
vacuum cleaner with only the
accessory hose attached.
Hard oor cleaning
Hard oor cleaning tool.
Line up oor tool with base of vacuum
cleaner, push it until it clicks into place.
Lie vacuum cleaner on its
back exposing brushbar.
Hold vacuum cleaner with brush bar over tread of stairs.
Using on the stairs
Always raise the height of the brush bar to hard oor setting when using the vacuum cleaner on lino and hard oor.
Using your machine
TIP
Filters require cleaning at least
every three months.
This vacuum cleaner has a
constantly rotating brushbar. When
cleaning on stairs raise the height
adjuster dial to the highest setting.
The brushbar must overhang the
stair tread. Always take care when
cleaning stairs.
WARNING
Press the dirt container
release button, pull to remove.
Emptying the dirt container
Cleaning the HEPA pre-motor lter
Hold dirt container
over a bin.
Press the dirt release clip,
allowing dirt/debris to fall out.
Turn the dirt container
release button, pull
to remove.
24hr
Leave to dry for
24 hours or until
fully dry before
placing back in the
vacuum cleaner.
Turn the HEPA
pre-motor lter
anti-clockwise,
pull to remove.
Tap HEPA pre-motor
lter over a bin to remove
any dirt/debris.
Rinse under water
(max 40°C).
Line up HEPA
pre-motor lter tabs
in dirt container lid,
turn clockwise until it
clicks into place.
Taking care of your machine
Filters require cleaning at least every 3-6 months (depending on the level of use).
Don’t use your vacuum cleaner without all the lters in place.
IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the machine should overheat, the
thermostat will automatically turn the machine o. Switch o and unplug the vacuum cleaner. Check the machine
for blockages and clean the lters. Wash the lters with warm water (40°C max) and leave for 24 hours or until
fully dry before replacing into the machine.
TIP
Don’t over ll the dirt
container to avoid blocking
the air ow through the
vacuum cleaner and replace
lters every 6-9 months.
Cleaning the post motor lter
Cleaning the separator
Press post motor
lter cover clip, pull
to remove.
Turn separator
anti-clockwise
to ‘unlock’, pull
to remove.
Remove any dirt/
debris. Rinse under
water (max 40°C).
Using a soft brush
clean any dirt/debris
out of the separator.
Remove post
motor lter.
Tap separator over
a bin to remove any
dirt/debris.
Leave to dry for 24
hours or until fully dry
before placing back in
the vacuum cleaner.
24hr
Line up tabs on
separator with dirt
container, turn
separator clockwise
to ‘lock’ and click
into place.
The separator
should sit on seal
in bottom of dirt
container when
correctly tted.
Taking care of your machine
Taking care of your machine
Pull hose out of hose to
machine connector.
Wrap hose around hose guide. Over and behind carry handle.
Into hose to machine connector.
Attach accessory hose
to extension hose.
Storing extension hose on vacuum cleaner (optional)
Storing your vacuum cleaner
Wrap the power
around the quick
cord release hooks.
Press handle
release button.
Lower handle
downwards.
Always use the carry
handle to lift and carry
the machine.
Removing dirt/debris from TurboTool (some models only)
Removing debris from the brushbar
Using a pair of
scissors cut any hair
or debris free from
around the brushes.
Line up the tabs on front
of the housing and re-t.
Slide locking ring into
groove to secure.
Slide the locking ring
to remove.
Using a pair of scissors
remove any threads or
hair caught around the
brush bar.
Tabs
Lift and separate
the housing.
IMPORTANT: Unplug and switch o vacuum cleaner before performing maintenance or troubleshooting checks.
Let’s talk technical
TIP
To test for a blockage in the hose,
drop a small ball of paper through
the hose. The paper will drop
through if the hose is clear.
Replacing the belt
Place belt on rounded
area of brush bar
without bristles.
Line up right side of
brush bar with base,
push into place. Lift and
push left side of brush
bar until clicks into place.
Lie vacuum cleaner
on its back exposing
brush bars. Use a cross
head screwdriver.
Undo 5 screws.
Line up brush bar
cover, push until it
clicks into place.
Replace 5 screws
and tighten.
Lift to remove
brushbar cover.
Lift to remove brush
bar. Remove and
dispose of old belt.
Clean any debris from
spindle. Place new
belt on spindle.
Pull hose out of
hose to machine
connector.
Lift clip under the
hose inlet.
Pull latch out and
remove hose.
Remove any
blockage by
inserting wire coat
hanger into hose.
Line up latch,
push until it clicks
into place.
Removing a blockage from the hose
Let’s talk technical
If the brushbar does not rotate
easily then the belt may not
have been tted correctly. Make
sure the belt is not twisted.
WARNING
• Check the ‘This pack contains’ panel on the box to make sure
the part is included with your vacuum cleaner.
• The plug may not be fully pushed into the electrical socket.
• Check the fuse in the plug if this needs replacing, always replace
with a 13amp fuse.
• The motor thermostat may have tripped. If this has happened, unplug
the vacuum cleaner. Remove and empty the dirt container and check the
hose for blockages. Clean the lters and allow the vacuum cleaner to cool
for approximately 1 hour (if you have washed the lters you will need
to wait 24 hours for the lters to fully dry before putting them back into
the vacuum cleaner).
• The brushbar may be clogged, check the brush bar and clear
any hair or debris. Go to ‘Let’s talk technical’.
• The belt might be broken, go to ‘Let’s talk technical’.
• There may be a blockage in the hose. Please remove the hose from the
vacuum cleaner, check and clear any blockages. Go to ‘Let’s talk technical’,
• Empty the dirt container and clean lters. Go to ‘Taking care of your machine’.
• The brushbar may not be turning. Go to ‘My brushbar isn’t turning’ below.
• The brush bar height adjuster dial may not be set to the correct setting.
Go to ‘Using your machine’.
• If the accessory/tool will not pick up, check and clear any blockages.
Go to ‘Let’s talk technical’.
SolutionProblem
Is there an accessory
missing?
Why does my vacuum
cleaner have no power?
Why won’t the vacuum
cleaner pick up?
My brushbar
isn’t turning.
What to do if it goes wrong
†
Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
†
Getting in touch
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
TurboTool (Type 6)
1-1-134419
Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking up
stubborn pet hair.
Pro cleaning kit (Type 2)
1-1-133326
All our best tools all in one kit that makes cleaning
your home quicker, easier and with even better results.
We’ve taken care of cleaning all of the hard to reach
areas such as on top of cupboards and in between
blinds to the dust that collates behind and
within the radiator.
Accessories
Notes
Notes
@VaxUK
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich, Worcestershire, WR9 0LW, UK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
U86-AN-Be/U86-AN-Pe/U86-IN2-Pe is manufactured in compliance with the following Directives: Safety: 2006/95/EC Low
Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
© 2016 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care
Technology Ltd and is registered in the EU and may be pending or registered in other countries.
Loading...