Vax 6121 User Manual

6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 1
User Guide
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
Multifunction
Get Cleaning...
What’s your Vax model number? (Located on the top flap of the packaging)
e.g. 6 12 1 T
Note these down in case you need them in future. Please keep instructions for further use.
vax.co.uk
6121 series
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 2
---
Machine Overview
Solution pump button (green)
1
Power button (red)
2 3 Carry handle 4 Power cord
Lid release clips
5 6 Hose connection port 7 Solution tube port
Post motor filter cover (hidden)
8
Hose
9
10 Solution delivery tube
11 Hose connector
12 Solution delivery tube to
machine connector
13 Solution delivery tube to wash
head/tool connector 14 2 piece extension tube 15 Fibreflow wash head 16 Wash tool 17 Vax carpet cleaning solution 18 Combination floor head 19 3 x paper dust bags
20 Crevice tool
21 Dusting brush
22 Upholstery tool 23 Pleated pre motor filter
24 Foam post-motor filter 25 Foam pre-motor filter
3
8
7
6
9
10
12
1
2
16
11
13
4
1
4
5
15
18
17
PLEASE NOTE: some parts may vary according to model. Please check inside flap of box for more details.
23
Filters
2
19
Unit and accessories
24 25
Vax Careline: (UK) 0844 412 8455
20
22
21
(ROI) 1-800 928 308
!
!!!
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 3
General Safety Information
FOR HOUSEHOLD USE ONLY.
hen usingthe multifunction cleaner basic safetyprecautions
W
should always be observed, including the following:
1. Do not leave the multifunction cleanerunattended when
lugged in. Unplugit from the socket whennot in use.
p
. To prevent electric shockdo not use outdoors.
2
3. Notto be used as a toy.
4. Childrenshould be supervised to ensure that they do not
lay with the appliance.
p
. Thisapplianceis not intended for use by persons (including
5
children)withreduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
theyhavebeengiven supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
6. Useonlyas described in this manual. Use onlyVax
recommended attachments.
7. Do not use the multifunction cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the multifunction cleaner with a
damaged cord or plug. If the supply cord is damaged,
it must be replaced by the manufacturer or a
recommended Service Agent to avoid hazard and
invalidating the guarantee.
8. Do not handlethe plug or multifunction cleanerwithwet
hands. Do not use outdoors.
9. Do not put any objects into openings or operatewith
openings blocked. Keepthemfreeof anything that might
reduce airflow.
10. Keep hair,loose clothing, fingers and all parts of body away
fromopenings and movingparts.
11. Do not pick up hot coals, cigarette butts, matches or any
hot,smoking or burning objects.
12. Do not use the carpet washing function without the
solution tank and dirty watertank in place.
13. Do not use the multifunctioncleaner in dry mode without
the dust bag in place.
14. Turn off all controls before unplugging.
15. Do not vacuumup harmful or toxicmaterial(chlorine,
bleach, ammonia, drain cleaner etc.).
16. Do not vacuumup hard or sharp objects such as glass,
nails, screws,coins, etc.
17. Use only CE-approved13 amp extension cords.
Non-approved cords may overheat. Careshould be
akento arrange the cordso that the cord cannotbe
t
ripped over.
t
8. Store the multifunction cleaner in a cool, dry area.
1
19. To preventdirty water from running into motor, do not hold
the appliance upside-down or lay on its side. Use
appliancein normalvacuuming/carpet washingposition.
20. Take extracare when cleaningon stairs.
1. Turn off the on/off switch before unplugging the multi-
2
function cleaner.
2. Do not carry appliance while motoris running.
2
WARNING: Always switch off and unplug the
multifunction cleaner from the electrical outlet before
assembling, opening, emptying the dirt container/dirty water
tank, before connecting/disconnecting the attachments, or
carrying out maintenance or troubleshooting checks.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
IMPORTANT: If the inlet, hose or telescopic tube is
blocked, switch off the multifunction cleaner and
remove the blockage(s) before re-starting the multifunction
cleaner.
IMPORTANT: Cleaning filters maintains vacuum
performance. Vax recommends that your filters
should be checked and cleaned periodically. If your filters are
washable make sure they are completely dry before
inserting back into the multifunction cleaner.
IMPORTANT: The motor is equipped with a thermal
cut-out. If for any reason the unit should overheat, the thermostat will automatically turn the unit off. Should this occur, unplug the multifunction cleaner from the electrical outlet and turn off the switch. Clean filters. Allow the unit to cool for approximately one (1) hour. To re-start, plug into an electrical outlet and switch back on.
This multifunction is intended for household use only and NOT for commercial or industrial use.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.
vax.co.uk
3
!
!
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 4
---
Operation
WARNING: Unplug your multifunction cleaner before performing maintenance/troubleshooting checks.
Vacuuming
Assembling your multifunction cleaner (dry vacuuming)
1
1
Lift up clips to remove lid.
Remove clean water tank from unit.
2
1
2
Remove the float housing from the lid.
Fit the pleated pre­motor filter to the lid.
NOTE: The crevice tool, dusting brush and upholstery tool, can all be
attached to the telescopic tube/handle.
Slide dust bag into the slots inside the base of the unit.
2
Fit the plug.
Press down on clips to secure.
1
2
NOTE: Fully unwind power cord.
Vax Careline: (UK) 0844 412 8455
4
(ROI) 1-800 928 308
!
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 5
Operation
Before you begin carpet washing
IMPORTANT: Do not use the cleaner as a dry vacuum when set up in carpet washing mode.
NOTE: Do not over saturate your carpet.
• Vacuum your carpets thoroughly.
• Test for colourfastness - Wet a white absorbent cloth with the solution. In a small, hidden area of your carpet, gently rub the surface with the dampened cloth. Wait ten minutes and check for colour removal or bleed with white paper towel or cloth. If your carpet has more than one colour, check all colours.
• When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture is too heavy to move, place aluminium foil or wax paper under legs. This will prevent wood finishes from staining your carpet. Pin up furniture skirts and curtains.
Helpful hints for washing carpet:
1. For heavy soiled areas, additional applications may be necessary.
2. Allow plenty of time to dry carpet thoroughly.
3. Try not to walk on carpet until it is completely dry.
4. After carpet is thoroughly dry, vacuum the carpet using your vacuum cleaner in dry mode.
5. Before cleaning, determine where to start and end, making sure not to walk over previously
cleaned areas.
6. Thoroughly clean the dirty water tank and clean water tank after use with warm water
(max 40°C).
.
vax.co.uk
5
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 6
---
Operation
Assembling your multifunction cleaner (carpet washing)
2
1
Lift up clips to remove lid.
2
Attach float to the lid.
Press down on clips to secure.
Remove filter. Remove plug.
1
Fill clean water tank with warm water (max 40º C). Add 40ml of Vax solution per 1 litre of water, unless otherwise stated on the bottle.
1
2
Replace the clean water tank inside the dirty water tank.
Attach hose to unit. Ensure solution tube is wrapped loosely around the hose and extension tubes. Secure in place with the clips provided.
Attach the solution pump hose.
Attach the lid ensuring the solution pump hose is inside the clean water tank.
2
1
6
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 7
Operation
Operating the appliance (carpet washing mode)
1
2
Red button – power.
Green button – activate pump.
Washing carpets
NOTE: For best results apply solution on the forward stroke and recover solution on the
backward stroke.
Ensure rocker switch is towards the back of the Fibreflow wash head to allow water flow.
To suck up excess water push the rocker switch to the front.
Washing upholstery
Attach the wash tool directly onto the handle of the hose and wrap the excess solution tube around as necessary.
vax.co.uk
To start water and solution flow, push the collar on the wash tool forwards.
To recover excess water and solution, pull the collar backwards.
7
24hr
!
!
!
t
a
p
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 8
---
Maintenance (Keep your Vax as good as new)
WARNING: Unplug your multifunction cleaner before performing maintenance/troubleshooting checks.
Emptying and replacing the dust bag
Insert new dust bag.
IMPORTANT: The condition of the filters affects the performance of your machine. Please check, wash/change filters periodically (depending on level of use).
Cleaning the post motor filter
40° C max
Cleaning the pleated pre motor filter assembly
WARNING:
Do not wash the pleated pre motor filter assembly.
8
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
!
t
a
p
!
24hr
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 9
Maintenance (Keep your Vax as good as new)
WARNING: Unplug your multifunction cleaner before performing maintenance/troubleshooting checks.
Cleaning the pre-motor filter
1
2
Remove the float housing from the lid.
40° C max
Emptying and cleaning the clean and dirty water tanks
NOTE: Thoroughly
clean the dirty water/clean water tanks after use with warm water
40° C)
(max
Clearing blockages
Hose Blockages
Disconnect the hose from your machine. Carefully remove any blockages found and reconnect the hose securely.
vax.co.uk
Accessory Blockages
Remove accessory from the hose or tube. Carefully remove the blockage and return to the cleaner.
9
!
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 10
---
FAQs
WARNING: To reduce the risk of personal injury, unplug your multifunction cleaner before performing maintenance/troubleshooting checks.
Is there an accessory missing?
• Check the parts overview page to make sure the attachment is supplied with your unit.
• If it is missing, please call our Vax Careline to order a replacement: 0844 412 8455 or visit vax.co.uk to order online.
Why won’t my multifunction cleaner put down water/solution mix?
• Check there is water/solution mix in the clean water tank.
• Ensure the solution tube on the underside of the motor housing has been released and is in the clean water tank.
• Check that the pump button on the carry handle has been switched on.
• Ensure the foot pedal on the wash head is positioned to the back of the wash head.
• Ensure the collar on the wash tool is pushed forward.
Why won’t my multifunction cleaner recover water?
• The dirty water tank may be full.
• The wash tool/fibreflow wash head might have an obstruction.
What do I do if an accessory/the unit has become damaged or broken?
• We’re here to help. Simply call 0844 412 8455 or visit vax.co.uk
Why wont the multifunction cleaner pick up in dry mode?
• A filter may be clogged; refer to maintenance section for cleaning instructions.
• The dust bag may be incorrectly fitted, check assembling your machine in dry mode.
• The dust bag may be full, check and replace with a new dust bag.
• Check for blockages in the hose/floorheads/accessories.
Why is dust escaping from my multifunction cleaner in dry mode?
• The filters may be incorrectly installed, check that they are fitted correctly.
• The dust bag may be incorrectly fitted, check assembling your machine in dry mode.
Vax Careline: (UK) 0844 412 8455
10
(ROI) 1-800 928 308
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 11
Other Information
UK Service & Help
Vax Careline:
(UK) 0844 412 8455
(ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm
Saturday-Sunday 9.00am to 5.00pm
If you have queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the UK local rate. Please make a note of the serial number and model number of the vacuum cleaner before calling. For the nearest Service Agent, please call the Vax Customer Careline or visit vax.co.uk
Consumables
To purchase spares and accessories, please visit vax.co.uk
6121 series maintenance kit: 1-9-127562-00 6121 series filter kit: 1-9-127558-00
Technical Specification
Voltage: 220-240V ~50Hz Wattage: 1300 W Capacity: Dust bag 10 litres
Cord Length: 10m Weight: 7.8kg
Subject to technical change without notice.
EEC Statement of Compliance
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the 6121 series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of withhousehold waste. Please recycle where facilities exist. Check with your LocalAuthority or retailer for recyclingadvice.
Clean water tank 4 litres Dirty water tank 4 litres
vax.co.uk
11
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 12
---
Notes
12
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 13
Notes
vax.co.uk
13
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 14
Notes
14
Vax Careline: (UK) 0844 412 8455
(ROI) 1-800 928 308
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 15
Notes
vax.co.uk
15
6121 Multivax Series User Guide v1.2.qxd:User guide 28/1/11 14:58 Page 16
---
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: vax.co.uk
Version 1.2
Loading...