Varytec QUAD VISOR FX User Manual

User manual
QUAD VISOR FX
2 / 6
Table of content
1. Safety instructions ........................................................................................................................... 3
1.1. FOR SAFE AND EFFICIENT OPERATION ............................................................................ 3
2. Technical data ................................................................................................................................. 4
3. Operation ......................................................................................................................................... 4
3.1. Functions via DIP .................................................................................................................... 4
3.2. Auto Mode ............................................................................................................................... 5
3.3. Sound Mode ............................................................................................................................ 5
3.4. Master/Slave Mode .................................................................................................................. 5
4. DMX Control .................................................................................................................................... 5
3 / 6
1. Safety instructions
This device is suitable for indoor use only.
All modifications to the device will void the warranty.
Repairs are to carry out by skilled personnel only.
Use only fuses of the same type and original parts as spare parts.
Protect the unit from rain and humidity to avoid fire and electric shocks.
Make sure to unplug the power supply before opening the housing.
1.1. FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature
Avoid exposing it to direct rays of the sun or near a heating appliance. Not put it in a temperature bellow 41°F /5°C, or ex ceeding 113°F /45°C.
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust. Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. When not using the device for an extended period of time, be sure to disconnect the plug from the receptacle
.
Important: Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or problems. Make sure the electrical connection is carried out by qualified personnel. All electrical and mechanical connections have to be carried out according to the European safety standards.
4 / 6
2. Technical data
Power supply 90-250VAC, 50~60Hz Power consumption 45W Current 0.36A Sound Control Via built-in microphone DMX512 connection 3 Pin XLR Weight 3.05 Kg Measurements 250 x 250 x 230 mm Maximum ambient temperature 45°C Maximum housing temperature 50°C Fuse F1A, 250V Channel 5 Number of LEDs 2 x 9W, 108 x 5mm
3. Operation
3.1. Functions via DIP
Function
DIP1
DIP2
DIP3
DIP4
DIP5
DIP6
DIP7
DIP8
DIP9
DIP10
MODE
Red
1
0 0 0 0 0 0 0 0 0 Auto (Master)
Green 0
1
0 0 0 0 0 0 0 0 Auto (Master)
Blue 0 0
1
0 0 0 0 0 0 0 Auto (Master)
Purple/White Strobe slow
0 0 0
1
0 0 0 0 0 0 Auto (Master)
RGB Strobe slow
0 0 0 0
1
0 0 0 0 0 Auto (Master)
RG Strobe fast
0 0 0 0 0
1
0 0 0 0 Auto (Master)
Motor mode 0 0 0 0 0 0
1
0 0 0 Auto (Master)
Auto 0 0 0 0 0 0 0
1
0 0 Auto (Master)
Sound Control
0 0 0 0 0 0 0 0
1
0 Sound Control
(Master)
Master/Slave 0 0 0 0 0 0 0 0 0
1
Auto (Master)
5 / 6
3.2. Auto Mode
In order to select Auto mode, set DIP switch 1 to 10 to OFF, set DIP switch 8 to ON.
3.3. Sound Mode
In order to select Sound Control Mode, set DIP switch 1 to 10 to OFF, set DIP switch 9 to ON.
3.4. Master/Slave Mode
In order to select Master/Slave Mode, set Auto Mode or the Sound Control Mode from DIP switch 1 to 9 to OFF, set DIP switch 10 to ON. In Master/Slave operation one unit will act as the controlling unit and the others will react to the controlling unit’s built-in programs.
4. DMX Control
Channel
Value
Function
CH1 000-004
005-028 029-056 057-084 085-112 113-140 141-168 169-197 198-224 225-255
LED Close Red Green Blue Blue/Green Red/Blue Green/Red Red/Green/Blue Tri color chase automatically Seven color chase automatically
CH2 000-004
005-255
No strobe Strobe from slow to fast
CH3 001-127
128-255
Motor positive rotation Motor reversion rotation
CH4 000-063
064-127 128-191 192-255
LED Close Purple White Purple/White
CH5 000-004
005-255
No strobe Strobe from slow to fast
6 / 6
Importer:
B & K Braun GmbH
Industriestraße 1
D-76307 Karlsbad
www.bkbraun.com
info@bkbraun.com
Loading...