Hero Spot Wash 80
2in1 RGBW+W
User manual
moving head
Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: info@thomann.de
Internet: www.thomann.de
05.04.2019, ID: 451570
Table of contents
Table of contents
1 General notes............................................................................................................................................... 6
1.1 Further information........................................................................................................................... 7
1.2 Notational conventions.................................................................................................................... 8
1.3 Symbols and signal words............................................................................................................... 9
2 Safety instructions.................................................................................................................................. 11
3 Features....................................................................................................................................................... 19
4 Installation.................................................................................................................................................. 21
5 Starting up.................................................................................................................................................. 27
6 Connections and controls................................................................................................................... 30
7 Operating.................................................................................................................................................... 33
7.1 Starting the device........................................................................................................................... 33
7.2 Main menu.......................................................................................................................................... 34
7.3 Functions in 8-channel DMX mode........................................................................................... 43
7.4 Functions in 15-channel DMX mode........................................................................................ 46
7.5 Functions in 20-channel DMX mode........................................................................................ 52
Hero Spot Wash 80 2in1 RGBW+W
moving head
3
Table of contents
7.6 Gobos................................................................................................................................................... 60
8 Technical specications....................................................................................................................... 61
9 Plug and connection assignments.................................................................................................. 63
10 Troubleshooting...................................................................................................................................... 64
11 Cleaning....................................................................................................................................................... 66
12 Protecting the environment.............................................................................................................. 67
Hero Spot Wash 80 2in1 RGBW+W
4
moving head
Hero Spot Wash 80 2in1 RGBW+W
moving head
5
General notes
1 General notes
This manual contains important instructions for the safe operation of the unit. Read and follow
the safety instructions and all other instructions. Keep the manual for future reference. Make
sure that it is available to all those using the device. If you sell the unit please make sure that
the buyer also receives this manual.
Our products are subject to a process of continuous development. Thus, they are subject to
change.
Hero Spot Wash 80 2in1 RGBW+W
6
moving head
1.1 Further information
General notes
On our website (www.thomann.de) you will nd lots of further information and details on the
following points:
Download This manual is also available as PDF le for you to download.
Keyword search
Online guides
Personal consultation For personal consultation please contact our technical hotline.
Service
Use the search function in the electronic version to nd the topics of
interest for you quickly.
Our online guides provide detailed information on technical basics
and terms.
If you have any problems with the device the customer service will
gladly assist you.
Hero Spot Wash 80 2in1 RGBW+W
moving head
7
General notes
1.2 Notational conventions
This manual uses the following notational conventions:
Letterings
Displays
Cross-references
Hero Spot Wash 80 2in1 RGBW+W
8
moving head
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’.
References to other locations in this manual are identied by an arrow and the specied page
number. In the electronic version of the manual, you can click the cross-reference to jump to
the specied location.
Example: See Ä ‘Cross-references’ on page 8.
1.3 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words that are
used in this manual.
Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
WARNING! This combination of symbol and signal word indicates a pos‐
CAUTION! This combination of symbol and signal word indicates a pos‐
NOTICE! This combination of symbol and signal word indicates a pos‐
General notes
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
sible dangerous situation that can result in death or serious
injury if it is not avoided.
sible dangerous situation that can result in minor injury if it
is not avoided.
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Hero Spot Wash 80 2in1 RGBW+W
moving head
9
General notes
Warning signs Type of danger
Warning – high-voltage.
Warning – dangerous optical radiation.
Warning – suspended load.
Warning – danger zone.
Hero Spot Wash 80 2in1 RGBW+W
10
moving head
2 Safety instructions
Safety instructions
Intended use
This device is intended for use as a freely moving multifunctional spotlight. The device is
designed for professional use and is not suitable for use in households. Use the device only as
described in this user manual. Any other use or use under other operating conditions is consid‐
ered to be improper and may result in personal injury or property damage. No liability will be
assumed for damages resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Extend the operating life of the device by regular breaks and by avoiding frequent switching
on and o. The device is not suitable for continuous operation.
Hero Spot Wash 80 2in1 RGBW+W
moving head
11
Safety instructions
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers.
There are no user-serviceable parts inside.
Do not use the device if covers, protectors or optical components are missing or
damaged.
Hero Spot Wash 80 2in1 RGBW+W
12
moving head
Safety instructions
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a pro‐
tective contact plug. Do not modify the mains cable or the plug. Failure to do so
could result in electric shock/death or re. If in doubt, seek advice from a regis‐
tered electrician.
WARNING!
Eye damage caused by high light intensity
Never look directly into the light source.
WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons
should avoid looking at strobe lights.
Hero Spot Wash 80 2in1 RGBW+W
moving head
13
Safety instructions
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that apply
in your country. Always secure the device with a secondary safety attachment,
such as a safety cable or a safety chain.
The load capacity of trusses or other xtures must be sucient for the intended
number of devices. Not that the movement of the head places additional loads on
the load-bearing parts.
Hero Spot Wash 80 2in1 RGBW+W
14
moving head
Safety instructions
CAUTION!
Risk of injury due to movements of the device
The head of the device can move quickly (pan, tilt) and can produce very bright
light. This is also valid immediately after you turn on the device, when the device
operates in automatic mode or under remote control and when you turn o a
DMX controller that is connected to the device. Persons staying near the device
could be injured or frightened.
Before you turn on the device and during the operation, always ensure that
nobody stays close to the device. If work has to be performed in the area of move‐
ment or in the near vicinity of the device, it must remain turned o.
NOTICE!
Risk of re
Do not block areas of ventilation. Do not install the device near any direct heat
source. Keep the device away from naked ames.
Hero Spot Wash 80 2in1 RGBW+W
moving head
15
Safety instructions
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.
Only operate the device within the ambient conditions specied in the chapter
‘Technical specications’ of this user manual. Avoid heavy temperature uctua‐
tions and do not switch the device on immediately after it was exposed to tem‐
perature uctuations (for example after transport at low outside temperatures).
Dust and dirt inside can damage the unit. When operated in harmful ambient
conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by
qualied service personnel at regular intervals to prevent overheating and other
malfunction.
The device must not be moved during use.
Hero Spot Wash 80 2in1 RGBW+W
16
moving head
Safety instructions
NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or re.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react
with the coating of your parquet, linoleum, laminate or PVC oor and after some
time cause permanent dark stains.
In case of doubt, do not put the rubber feet directly on the oor, but use felt-pad
oor protectors or a carpet.
Hero Spot Wash 80 2in1 RGBW+W
moving head
17
Safety instructions
NOTICE!
Risk of overheating
The distance between light output and the illuminated surface must be more
than 1.5 m (19.7in).
Provide sucient ventilation.
The ambient temperature must always be below 40 °C (104 °F).
Hero Spot Wash 80 2in1 RGBW+W
18
moving head
3 Features
Features
The Moving Head is ideal for mobile DJs, entertainers and use in bars.
Special features of the device:
n 6 × 4in1 LED ring (RGBW, each 8 W)
n 1 × LED white light spot (30 W)
n Control via DMX (8, 15 or 20 channels) and via buttons and display on the unit
n Preprogrammed automatic show programmes
n Two movable axles with 16 bit resolution:
– Tilt (190°)
– Pan (540°)
n Sound control
n Master / Slave mode
n Gobo wheel with 7 rotatable gobos
n Gobo-ow and gobo-shake functions
n Electronic dimmer
n Electronic shutter 0 … 20 Hz
Hero Spot Wash 80 2in1 RGBW+W
moving head
19
Features
For technological reasons, the light output of LEDs decreases over their lifetime. This eect
increases with higher operating temperature. You can extend the service life of the illuminants
by providing adequate ventilation and operating the LEDs with the lowest possible brightness.
Hero Spot Wash 80 2in1 RGBW+W
20
moving head
4 Installation
Installation
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the product against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
Lift the device only at the base. When lifted at the rotatable mounting, the device may be dam‐
aged.
You can install the device standing or hanging. When in use, the device must be mounted at a
solid surface or clamped to an approved truss.
Work from a stable platform whenever you install or move the device or when you perform
any kind of maintenance. Block access under the work area.
Hero Spot Wash 80 2in1 RGBW+W
moving head
21
Installation
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that apply
in your country. Always secure the device with a secondary safety attachment,
such as a safety cable or a safety chain.
The load capacity of trusses or other xtures must be sucient for the intended
number of devices. Not that the movement of the head places additional loads on
the load-bearing parts.
Hero Spot Wash 80 2in1 RGBW+W
22
moving head
Installation
CAUTION!
Risk of injury due to movements of the device
The head of the device can move quickly (pan, tilt) and can produce very bright
light. This is also valid immediately after you turn on the device, when the device
operates in automatic mode or under remote control and when you turn o a
DMX controller that is connected to the device. Persons staying near the device
could be injured or frightened.
Before you turn on the device and during the operation, always ensure that
nobody stays close to the device. If work has to be performed in the area of move‐
ment or in the near vicinity of the device, it must remain turned o.
NOTICE!
Risk of overheating
The distance between light output and the illuminated surface must be more
than 1.5 m (19.7in).
Provide sucient ventilation.
The ambient temperature must always be below 40 °C (104 °F).
Hero Spot Wash 80 2in1 RGBW+W
moving head
23
Installation
NOTICE!
Possible damage caused by movements of the device
Always ensure that enough space is free around the device for the movements of
the head (pan, tilt).
NOTICE!
Possible data transmission errors
For error-free operation make use of dedicated DMX cables and do not use ordi‐
nary microphone cables.
Never connect the DMX input or output to audio devices such as mixers or ampli‐
ers.
Hero Spot Wash 80 2in1 RGBW+W
24
moving head
Mounting options
Installation
The threads on the bottom side of the housing (A) allow the secure attachment of the included
mounting bracket. There, you can fasten adapters such as half couplers, trigger clamps, chooks etc. Safety cables are being threaded through the eyelet (B) on the bottom side of the
housing.
Hero Spot Wash 80 2in1 RGBW+W
moving head
25
Installation
Please note that this device must not be connected to a dimmer.
Hero Spot Wash 80 2in1 RGBW+W
26
moving head
5 Starting up
Starting up
Create all connections while the device is o. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.
Hero Spot Wash 80 2in1 RGBW+W
moving head
27
Starting up
Connections in DMX mode
Connect the DMX input of the device to the DMX output of a DMX controller or another DMX
device. Connect the output of the rst DMX device to the input of the second one, and so on
to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain
is terminated with a resistor (110 Ω, ¼ W).
Hero Spot Wash 80 2in1 RGBW+W
28
moving head
Starting up
DMX indicator
Connections in master/slave
mode
When the device and the DMX controller are operational, the DMX indicator in the display
shows that a DMX signal is being received on the input.
When you congure a group of devices in master/slave mode, the rst unit will control the
other units for an automatic, sound-activated, synchronized show. This function is ideal when
you want to start a show immediately. Connect the DMX output of the master device to the
DMX input of the rst slave device. Then connect the DMX output of the rst slave device to
the DMX input of the second slave device and so on.
Hero Spot Wash 80 2in1 RGBW+W
moving head
29
Connections and controls
6 Connections and controls
Hero Spot Wash 80 2in1 RGBW+W
30
moving head
Connections and controls
1 Display
2 Built-in microphone for sound control
3 [MENU]
Activates the main and the settings menu and toggles between menu items. Closes an open submenu without
saving any changes.
4 [DOWN]
Decreases the displayed value by one.
5 [UP]
Increases the displayed value by one.
6 [ENTER]
Selects an option of the respective operating mode, conrms the set value.
7 [DMX IN]
DMX input.
8 [DMX OUT]
DMX output
Hero Spot Wash 80 2in1 RGBW+W
moving head
31
Connections and controls
9 Lockable input socket (Power Twist) for mains power supply
10 Fuse holder
Hero Spot Wash 80 2in1 RGBW+W
32
moving head
7 Operating
7.1 Starting the device
Operating
CAUTION!
Risk of injury due to movements of the device
The head of the device can move quickly (pan, tilt) and can produce very bright
light. This is also valid immediately after you turn on the device, when the device
operates in automatic mode or under remote control and when you turn o a
DMX controller that is connected to the device. Persons staying near the device
could be injured or frightened.
Before you turn on the device and during the operation, always ensure that
nobody stays close to the device. If work has to be performed in the area of move‐
ment or in the near vicinity of the device, it must remain turned o.
Connect the device to the power supply to start operation. After a few seconds, the fans start
to work, the head moves to the home positions for rotation (pan) and inclination (tilt). After a
few more seconds, the display shows ‘001’ .The device is now ready for operation.
Hero Spot Wash 80 2in1 RGBW+W
moving head
33
Operating
7.2 Main menu
Press [ENTER] to activate the main menu.
Use [UP] and [DOWN] to change the respectively indicated value. When the display shows the
desired value press [ENTER].
To exit the menu item without making changes, press [MENU].
If you don't press any button for about 30 seconds the display turns o. Then press [MENU],
[ENTER], [UP] or [DOWN] briey to turn it on again.
All previous settings are retained even when you switch the device o and disconnect it from
the mains.
DMX address
Hero Spot Wash 80 2in1 RGBW+W
34
moving head
Use the ‘DMX Address’ menu to set the DMX address.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows ‘DMX
Address’ . Conrm the selection with [ENTER] and use [UP] or [DOWN] to select a value between
1 and 512 to set the desired DMX address.
When the display shows the desired value conrm the setting with [ENTER]. To exit the menu
item without making changes, press [MENU].
Make sure that this number matches the conguration of your DMX controller.
Operating
DMX mode
Use the ‘DMX Channel’ menu to set the DMX mode.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows ‘DMX
Channel’ . Conrm the setting with [ENTER] and use [UP] or [DOWN] to select one of the three
DMX modes (8-channel mode, 15-channel mode or 20-channel mode, display shows ‘DMX 8
Ch’ , ‘DMX 15 CH’ or ‘DMX 20 Ch’).
When the display shows the desired value conrm the setting with [ENTER]. To exit the menu
item without making changes, press [MENU].
Hero Spot Wash 80 2in1 RGBW+W
moving head
35
Operating
Operating mode
Use the ‘Running Mode’ menu to set the operating mode.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows
‘Running Mode’ . Conrm the selection with [ENTER] and use [UP] or [DOWN] to select one of
the four operating modes ( ‘DMX’ , ‘Auto’, ‘Sound’, ‘Slave’).
Operating mode Function
‘DMX’ DMX control
In this mode the device is controlled via a DMX controller.
‘Auto’ Auto programmes
In this mode, the unit plays the preprogrammed shows.
‘Sound’ Sound control
In this mode, the unit follows the rhythm of the background music or
sounds detected by the built-in microphone.
‘Slave’ Slave function
In this mode, the device follows exactly the operation of the master
that it is connected to.
Hero Spot Wash 80 2in1 RGBW+W
36
moving head
Operating
When the display shows the desired value conrm the setting with [ENTER]. To exit the menu
item without making changes, press [MENU].
Auto programmes
Use the ‘Programs’ to select one of the preprogrammed shows.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows
‘Programs’ . Conrm the setting with [ENTER] and use [UP] or [DOWN] to select one of the eight
preprogrammed shows (display shows ‘Program1’ … ‘Program8’).
When the display shows the desired value conrm the setting with [ENTER]. The device plays
the selected show as an endless loop. To exit the menu item without making changes, press
[MENU].
Hero Spot Wash 80 2in1 RGBW+W
moving head
37
Operating
Settings
Use the ‘Settings’ menu to adjust the device parameters.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows
‘Settings’ . Conrm the selection with [ENTER] and use [UP] or [DOWN] to select the desired
parameter.
Parameter Function
‘Pan Rev’ Pan inversion
Use [UP] or [DOWN] to select ‘YES’ (reverse rotation) or ‘NO’ (normal
rotation).
‘Tilt Rev’ Tilt inversion
Use [UP] or [DOWN] to select ‘YES’ (reverse direction of inclination) or
‘NO’ (normal direction of inclination).
‘Display Rev’ Display inversion
Use [UP] or [DOWN] to select ‘YES’ (text in the display appears upside
down) or ‘NO’ (text in the display appears normal).
Hero Spot Wash 80 2in1 RGBW+W
38
moving head
Operating
Parameter Function
‘Sensitivity’ Microphone sensitivity
Use [UP] or [DOWN] to select a value from 0 (sound control o) to 100
(microphone sensitivity high).
‘Dmx Fail’ Behaviour on DMX control failure
Use [UP] or [DOWN] to select ‘OFF’ (blackout in case of DMX failure)
or ‘HOLD’ (last DMX signal is being held).
‘Calibration’ Calibrating
Detailed information about this menu item can be found under
Ä
‘Calibrating’ on page 40.
‘Factory Reset’ Reset to factory defaults
Use [UP] or [DOWN] to select ‘YES’ (factory reset) or ‘NO’ (no factory
reset).
‘Reset Motor’ Resetting the motor
When the display shows the desired value conrm the setting with [ENTER]. To exit the menu
item without making changes, press [MENU].
Hero Spot Wash 80 2in1 RGBW+W
moving head
39
Operating
Calibrating
Use the ‘Calibration’ menu to adjust the start parameters of the device.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows
‘Settings’ . Conrm the selection with [ENTER] and use [UP] or [DOWN] to select the submenu
‘Calibration’ .
Conrm the selection with [ENTER]. The device prompts you to enter a password. Press [UP] or
[DOWN] repeatedly until the display shows ‘018’ and conrm the selection with [ENTER].
Use [UP] or [DOWN] to select the desired parameter you want to set.
Parameter Function
‘All To Origin’ Resets all parameters of the calibration to factory settings.
‘Pan’ Sets the home position of the rotation.
‘Tilt’ Sets the home position of the inclination movement.
‘Red ’ Sets the initial intensity for red.
‘Green’ Sets the initial intensity for green.
‘Blue’ Sets the initial intensity for blue.
Hero Spot Wash 80 2in1 RGBW+W
40
moving head
Operating
Parameter Function
‘White’ Sets the initial intensity for white.
‘Spot Color’ Sets the initial colour of the spot.
‘Gobo’ Sets the rst gobo.
‘Focus’ Sets the home position for focus.
When the display shows the desired parameter conrm the setting with [ENTER]. Use [UP] or
[DOWN] to select the desired value for the selected parameter (0 … 120 for pan and tilt,
0 … 255 for red, green, blue, white, light bundling, spot colour and gobo) and conrm the set‐
ting with [ENTER]. To exit the menu item without making changes, press [MENU].
System information
Use the ‘System Info’ menu to call up information about the system.
Press [ENTER] to activate the main menu and use [UP] or [DOWN] until the display shows
‘System Info’ . Conrm the selection with [ENTER].
The display shows the current software version, the current operating mode and the DMX start
address.
Hero Spot Wash 80 2in1 RGBW+W
moving head
41
Operating
Menu overview
Hero Spot Wash 80 2in1 RGBW+W
42
moving head
7.3 Functions in 8-channel DMX mode
Channel Value Function
1 0…255 Rotation (pan) (0° up to the maximum value of the Pan area. middle position: 128)
2 0…255 Inclination (tilt) (0° up to the maximum value of the Tilt area. middle position: 128)
3 0…255 Wash: Dimmer intensity from dark (0) to bright (255)
4 Wash: Strobe / shutter (with dimmer open on channel 3)
0…9 Open
10…250 Stroboscope eect, increasing speed
251…255 Open
5 0…255 Spot: Dimmer intensity from dark (0) to bright (255)
6 Spot: Strobe / shutter (with dimmer open on channel 5)
0…9 Open
10…250 Stroboscope eect, increasing speed
Operating
Hero Spot Wash 80 2in1 RGBW+W
moving head
43
Operating
Channel Value Function
251…255 Open
7 Colour sequence and gobos
0…24 No function
25…50 Automatic colour sequence, color, gobo 1
51…75 Automatic colour sequence, color, gobo 2
76…100 Automatic colour sequence, color, gobo 3
101…125 Automatic colour sequence, color, gobo 4
126…150 Automatic colour sequence, color, gobo 5
151…175 Automatic colour sequence, color, gobo 6
176…200 Automatic colour sequence, color, gobo 7
201…255 Automatic colour sequence, colour, gobo (music control, from sound control o to high
microphone sensitivity)
8 Auto programmes
Hero Spot Wash 80 2in1 RGBW+W
44
moving head
Channel Value Function
0…10 No function
11…20 preprogrammed automatic show 1
21…30 Preprogrammed automatic show 2
31…40 Preprogrammed automatic show 3
41…50 Preprogrammed automatic show 4
51…60 Preprogrammed automatic show 5
61…70 Preprogrammed automatic show 6
71…80 Preprogrammed automatic show 7
81…90 Preprogrammed automatic show 8
91…230 Sound control, from sound control o to high microphone sensitivity
231…240 Reset, if the value is transmitted for at least 3 seconds
241…255 No function
Operating
Hero Spot Wash 80 2in1 RGBW+W
moving head
45
Operating
7.4 Functions in 15-channel DMX mode
Channel Value Function
1 0…255 Rotation (pan) (0° up to the maximum value of the Pan area. middle position: 128)
2 0…255 Inclination (tilt) (0° up to the maximum value of the Tilt area. middle position: 128)
3 0…255 Wash: Dimmer intensity from dark (0) to bright (255)
4 Wash: Strobe / shutter (with dimmer open on channel 3)
0…9 Open
10…250 Stroboscope eect, increasing speed
251…255 Open
5 0…250 Intensity red (0 % to 100 %)
6 0…250 Intensity green (0 % to 100 %)
7 0…250 Intensity blue (0 % to 100 %)
8 0…250 Intensity white (0 % to 100 %)
Hero Spot Wash 80 2in1 RGBW+W
46
moving head
Channel Value Function
9 Colour macros (with the dimmer open, channel 4 must be set between 251 and 255)
0…10 No function
11…20 Red
21…30 Green
31…40 Blue
41…50 White
51…60 Red, white
61…70 Green, white
71…80 Blue, white
81…90 Red, green
91…100 Green, blue
101…110 Red, blue
Operating
111…120 Red, green, white
Hero Spot Wash 80 2in1 RGBW+W
moving head
47
Operating
Channel Value Function
121…130 Green, blue, white
131…140 Red, blue, white
141…150 Red, green, blue, white
151…200 Colour change, increasing speed
201…255 Colour transition, increasing speed
10 0…255 Spot: Dimmer intensity from dark (0) to bright (255)
11 Spot: Strobe / shutter (with dimmer open on channel 5)
0…9 Open
10…250 Stroboscope eect, increasing speed
251…255 Open
12 Colour wheel
0…24 White (open)
25…50 Red
Hero Spot Wash 80 2in1 RGBW+W
48
moving head
Channel Value Function
51…75 Yellow
76…100 Light blue
101…125 Green
126…150 Amber
151…175 Purple
176…200 Blue
201…255 Colour wheel with alternating direction of rotation, rainbow eect, increasing speed
13 Gobo and gobo-shake function
0…10 Open (white)
11…20 Gobo 1
21…30 Gobo 2
31…40 Gobo 3
Operating
41…50 Gobo 4
Hero Spot Wash 80 2in1 RGBW+W
moving head
49
Operating
Channel Value Function
51…60 Gobo 5
61…70 Gobo 6
71…80 Gobo 7
81…90 Gobo 1 shake, increasing speed
91…100 Gobo 2 shake, increasing speed
101…110 Gobo 3 shake, increasing speed
111…120 Gobo 4 shake, increasing speed
121…130 Gobo 5 shake, increasing speed
131…140 Gobo 6 shake, increasing speed
141…150 Gobo 7 shake, increasing speed
151…255 Gobo rotation, clockwise and counterclockwise yo-yo eect, from fast to slow
14 0…255 Focus
15 Auto programmes
Hero Spot Wash 80 2in1 RGBW+W
50
moving head
Channel Value Function
0…10 No function
11…20 Preprogrammed automatic show 1
21…30 Preprogrammed automatic show 2
31…40 Preprogrammed automatic show 3
41…50 Preprogrammed automatic show 4
51…60 Preprogrammed automatic show 5
61…70 Preprogrammed automatic show 6
71…80 Preprogrammed automatic show 7
81…90 Preprogrammed automatic show 8
91…230 Sound control, from sound control o to high microphone sensitivity
231…240 Reset, if the value is transmitted for at least 3 seconds
241…255 No function
Operating
Hero Spot Wash 80 2in1 RGBW+W
moving head
51
Operating
7.5 Functions in 20-channel DMX mode
Channel Value Function
1 0…255 Rotation (pan) (0° up to the maximum value of the Pan area. middle position: 128)
2 0…255 Fine adjustment rotation (pan) 16 bit
3 0…255 Inclination (tilt) (0° up to the maximum value of the Tilt area. middle position: 128)
4 0…255 Fine adjustment inclination (pan) 16 bit
5 0…255 Speed of rotation (pan) and inclination (tilt), fast (0) to slow (255)
6 0…255 Wash: Dimmer intensity from dark (0) to bright (255)
7 Wash: Strobe / shutter (with dimmer open on channel 6)
0…9 Open
10…250 Stroboscope eect, increasing speed
251…255 Open
8 0…250 Intensity red (0 % to 100 %)
Hero Spot Wash 80 2in1 RGBW+W
52
moving head
Channel Value Function
9 0…250 Intensity green (0 % to 100 %)
10 0…250 Intensity blue (0 % to 100 %)
11 0…250 Intensity white (0 % to 100 %)
12 0…250 Gradual increase in colour temperature (0 % bis 100 %)
13 Colour macros (with the dimmer open, channel 7 must be set between 251 and 255)
0…10 No function
11…20 Red
21…30 Green
31…40 Blue
41…50 White
51…60 Red, white
61…70 Green, white
Operating
71…80 Blue, white
Hero Spot Wash 80 2in1 RGBW+W
moving head
53
Operating
Channel Value Function
81…90 Red, green
91…100 Green, blue
101…110 Red, blue
111…120 Red, green, white
121…130 Green, blue, white
131…140 Red, blue, white
141…150 Red, green, blue, white
151…200 Colour change, increasing speed
201…255 Colour transition, increasing speed
14 0…255 Spot: Dimmer intensity from dark (0) to bright (255)
15 Spot: Strobe / shutter (with dimmer open on channel 5)
0…9 Open
10…250 Stroboscope eect, increasing speed
Hero Spot Wash 80 2in1 RGBW+W
54
moving head
Channel Value Function
251…255 Open
16 Colour wheel
0…24 White (open)
25…50 Red
51…75 Yellow
76…100 Light blue
101…125 Green
126…150 Amber
151…175 Purple
176…200 Blue
201…255 Colour wheel with alternating direction of rotation, rainbow eect, increasing speed
17 Gobo and gobo-shake function
Operating
0…10 Open (white)
Hero Spot Wash 80 2in1 RGBW+W
moving head
55
Operating
Channel Value Function
11…20 Gobo 1
21…30 Gobo 2
31…40 Gobo 3
41…50 Gobo 4
51…60 Gobo 5
61…70 Gobo 6
71…80 Gobo 7
81…90 Gobo 1 shake, increasing speed
91…100 Gobo 2 shake, increasing speed
101…110 Gobo 3 shake, increasing speed
111…120 Gobo 4 shake, increasing speed
121…130 Gobo 5 shake, increasing speed
131…140 Gobo 6 shake, increasing speed
Hero Spot Wash 80 2in1 RGBW+W
56
moving head
Channel Value Function
141…150 Gobo 7 shake, increasing speed
151…255 Gobo rotation, clockwise and counterclockwise yo-yo eect, from fast to slow
18 0…255 Focus
19 Colour sequence and gobos
0…24 No function
25…50 Automatic colour sequence, color, gobo 1
51…75 Automatic colour sequence, color, gobo 2
76…100 Automatic colour sequence, color, gobo 3
101…125 Automatic colour sequence, color, gobo 4
126…150 Automatic colour sequence, color, gobo 5
151…175 Automatic colour sequence, color, gobo 6
176…200 Automatic colour sequence, color, gobo 7
Operating
Hero Spot Wash 80 2in1 RGBW+W
moving head
57
Operating
Channel Value Function
201…255 Automatic colour sequence, colour, gobo (music control, from sound control o to high
microphone sensitivity)
20 Auto programmes
0…10 No function
11…20 Preprogrammed automatic show 1
21…30 Preprogrammed automatic show 2
31…40 Preprogrammed automatic show 3
41…50 Preprogrammed automatic show 4
51…60 Preprogrammed automatic show 5
61…70 Preprogrammed automatic show 6
71…80 Preprogrammed automatic show 7
81…90 Preprogrammed automatic show 8
91…230 Sound control, from sound control o to high microphone sensitivity
Hero Spot Wash 80 2in1 RGBW+W
58
moving head
Channel Value Function
231…240 Reset, if the value is transmitted for at least 3 seconds
241…255 No function
Operating
Hero Spot Wash 80 2in1 RGBW+W
moving head
59
Operating
7.6 Gobos
Hero Spot Wash 80 2in1 RGBW+W
60
moving head
8 Technical specications
Illuminant 6 × 4in1 RGBW LED ring, 8 W
Beam angle Wash: 25°
Rotation angle (pan), max. 540°
Inclination angle (tilt), max. 190°
Number of DMX channels 8, 15 or 20, depending on operating mode
Power consumption 110 W
Technical specications
1 × LED white light spot, 30 W
Spot: 13°
Operating supply voltage
Fuse 5 mm × 20 mm, 2 A, 250 V, fast-acting
Protection class IP20
100 – 240 V 50/60 Hz
Hero Spot Wash 80 2in1 RGBW+W
moving head
61
Technical specications
Dimensions (W × H × D) 210 mm × 297 mm × 145 mm
Weight 4.5 kg
Environmental conditions
Temperature range 0 °C…40 °C
Relative humidity 50 %, non-condensing
Hero Spot Wash 80 2in1 RGBW+W
62
moving head
9 Plug and connection assignments
Plug and connection assignments
Introduction
DMX connections
This chapter will help you select the right cables and plugs to connect your valuable equip‐
ment so that a perfect light experience is guaranteed.
Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug
ts into a socket, the result of an incorrect connection may be a destroyed DMX controller, a
short circuit or ‘just’ a not working light show!
The unit oers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please
refer to the drawing and table below for the pin assignment of a suitable XLR plug.
Pin Conguration
1 Ground, shielding
2 Signal inverted (DMX–, ‘cold signal’)
3 Signal (DMX+, ‘hot signal’)
Hero Spot Wash 80 2in1 RGBW+W
moving head
63
Troubleshooting
10 Troubleshooting
In the following we list a few common problems that may occur during operation. We give you
some suggestions for easy troubleshooting:
NOTICE!
Possible data transmission errors
For error-free operation make use of dedicated DMX cables and do not use ordi‐
nary microphone cables.
Never connect the DMX input or output to audio devices such as mixers or ampli‐
ers.
Hero Spot Wash 80 2in1 RGBW+W
64
moving head
Symptom Remedy
Troubleshooting
The unit does not work, no light,
the fan does not run
No response to the DMX con‐
troller
If the procedures recommended above do not succeed, please contact our Service Center. You
can nd the contact information at www.thomann.de.
Check the mains power connection and the main fuse.
1. The DMX indicator should light up. If it doesn't, check
DMX connectors and cables for proper connection.
2. If the DMX indicator lights up but with no response,
check the address settings and DMX polarity.
3. Try using another DMX controller.
4. Check whether the DMX cables lie near or adjacent to
high voltage cables, which could cause damage or inter‐
ference with a DMX interface circuit.
Hero Spot Wash 80 2in1 RGBW+W
moving head
65
Cleaning
11 Cleaning
Optical lenses
Fan grids
Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the
light output. The frequency of cleaning depends on the operating environment: wet, smoky or
particularly dirty surroundings can cause more accumulation of dirt on the optics of the
device.
n Clean with a soft cloth using our lamp and lens cleaner (item no. 280122).
n Always dry the parts carefully.
The fan grids of the device must be cleaned of any contamination, such as dust, etc. on a reg‐
ular basis. Before cleaning, switch o the device and disconnect mains-operated devices from
the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit
with a slightly damp lint-free cloth.
Hero Spot Wash 80 2in1 RGBW+W
66
moving head
12 Protecting the environment
Disposal of the packaging mate‐
rial
For the transport and protective packaging, environmentally friendly materials have been
chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that
they are collected for recycling. Please follow the notes and markings on the packaging.
Disposal of your old device
This product is subject to the European Waste Electrical and Electronic Equipment Directive
(WEEE) in its currently valid version. Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal rm or through your local waste
facility. When discarding the device, comply with the rules and regulations that apply in your
country. If in doubt, consult your local waste disposal facility.
Protecting the environment
Hero Spot Wash 80 2in1 RGBW+W
moving head
67
Notes
Hero Spot Wash 80 2in1 RGBW+W
68
moving head
Notes
Hero Spot Wash 80 2in1 RGBW+W
moving head
69
Notes
Hero Spot Wash 80 2in1 RGBW+W
70
moving head
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de
Loading...