Page 1
Solutions for Demanding Applications
VARTECH
S Y S T E M S I N C.
15.0” Enclosed VESA Mount PC
Model VTPC150V / VS / VDC / VSDC / VHB / VSHB
Read these instructions completely before attempting to operate your new VESA Mount PC
User’s Guide
Page 2
Revision History
Date Rev No Summary Page
03/15/08 00 First Issue
07/22/08 01 Revised Enclosure & Specifications 5 & 6
10/31/08 02 Added VHB & VSHB versions 1, 4 – 7
07/10/09 03 Revised Detail A 8
08/05/09 04 Added VDC & VSDC versions 6 & 7
15.0 Enclosed VESA Mount PC 486-0007-00-04
2
Page 3
Safety Instructions
Read the Safety Instructions carefully and keep it for use later.
The chassis metalwork of the module must be installed properly to the main earthing termination
for Class 1 equipment.
Care must be exercised in the application of the system to prevent overheating. Ensure that the
ambient temperature around the system does not exceed 60°C and provide adequate means of
ventilation to achieve this.
When cleaning cut off the electrical supply at all times. Never use liquid or aerosol detergent,
use a soft damp cloth instead.
Never insert anything metallic into the chassis openings. This may create an electric shock
hazard or hazard from rotating fan blades.
To avoid electric shock, never touch the inside of the system. There are no user adjustable
components inside, only a qualified technician should open the system’s case.
To prevent overheating, the heat sink should not be blocked or covered.
If the system does not operate normally – in particular, if there are any unusual sounds or smells
coming from it – disconnect it immediately.
Do not put pressure on the LCD panel screen because it is very fragile.
Always handle the system with care when moving it.
Take care that the system is disposed of correctly at the end of its life. If in doubt refer to your
local ordinances or regulations for proper disposal.
A socket-outlet shall be installed near the equipment and shall be easily accessible.
Cleaning the LCD monitor
To clean the LCD panel:
Wipe the screen gently with a clean lens brush made of camel hair, or a soft, clean, lint free
cloth. This is to remove dust and other particles without scratching the LCD panel.
If it is still not clean, then wipe with a damp lint free cloth and blow on it to dry.
Do not clean the panel with a keton-type material (e.g. acetone), or ethyl toluene, ethyl acid, methyl or
chloride. These may damage the LCD panel.
Do not apply pressure to the LCD panel.
15.0 Enclosed VESA Mount PC 486-0007-00-04
3
Page 4
Standard Technical Specifications:
LCD Monitor:
STANDARD/Dual Core VERSION:
Size / Type
Native Resolution
Contrast Ratio
Viewing Angles
Pixel Pitch
Brightness (typical) 400 cd/m²
Response Time (typical)
Colors Supported:
15.0” XGA TFT LCD
1024 x 768
600:1
Horizontal: 140°
Vertical: 120°
0.294mm
7ms
16.7 million
HIGH-BRIGHT VERSION:
Size / Type
Native Resolution
Contrast Ratio
Viewing Angles
Pixel Pitch
Brightness (typical) 1500 cd/m²
Response Time (typical)
Colors Supported:
15.0” a-Si TFT LCD
1024 x 768
450:1 (contrast ratio >10:1)
Horizontal: 75°
Vertical: 75° upside, 55° downside
0.297mm
25ms
16.7 million
15.0 Enclosed VESA Mount PC 486-0007-00-04
4
Page 5
Standard Computer System:
Processor
System Memory
BIOS
Hard Drive
Operating System
Expansion Slots
I/O Ports
Graphics
LAN
Touch Screen
Touch Screen Interface
Dual Core Computer System:
Intel® Atom™ N270, 1.6 GHz Processor with a 533 Mhz FSB
DDR2 533 SO-DIMM 1 GB (system max 2GB)
AMI BIOS
500 GB SATA (system max 2x SATA)
Microsoft Windows XP Professional (SP3)
1x PCI Express Mini Card
AC Power Inlet x 1
COMM Port x 2 (RS232)
USB 2.0 Port x 3
RJ45 LAN Port x 1
Intel Generation 3.5 integrated GFX Core (133Mhz)
PCIe Realtek 8111CP GbE
Resistive
Serial
Processor
System Memory
BIOS
Hard Drive
Intel Pentium Dual Core T4500 2.30 GHz
DDR2 533 SO-DIMM 2 GB (system max 4GB)
AMI BIOS
500 GB SATA (system max 2x SATA)
Operating System Microsoft Windows XP Professional (SP3)
I/O Ports
AC Power Inlet x 1
COMM Port x 2 (RS232)
USB 2.0 Port x 3
RJ45 LAN Port x 1
Graphics
LAN
Intel GM 45 integrated graphics engine
Realtek RTL8111B
Touch Screen Resistive
Touch Screen Interface
Serial
15.0 Enclosed VESA Mount PC 486-0007-00-04
5
Page 6
Power Specifications:
Power Input
Power Consumption
Standard:
Dual Core:
High-Bright:
Temperature
Standard:
High-bright:
Humidity
Standard:
100-240 VAC 1.5A 50/60 Hz
30W
68W
75W
Operational: 14°F to 113°F -10°C to 45°C
Storage: -4°F to 149°F -20°C to 65°C
Dual Core Processor: 14°F to 104°F -10°C to 40°C
Operational: 14°F to 113°F -10°C to 45°C
Storage: -4°F to 149°F -20°C to 65°C
Dual Core Processor: 14°F to 104°F -10°C to 40°C
Operational: 0 to 90% RH NC
Storage: 0 to 95% RH NC
High-bright:
Absolute: 95% max RH NC (ambient temp 0-40°C)
85% max RH NC (ambient temp > 40°C, up to 50°C)
55% max RH NC (Ta > 50°C)
Installation of Your Enclosed VESA Mount PC
Packaged with each carton will be:
1 - VTPC150V / VS / VDC / VSDC / VHB / VSHB
1 - Users Guide (Printed or on CD)
Cables Provided (Only cables pertaining to the ordered I/Os will be provided )
1 x AC power cable
1 x USB cable
2 x RS232 cable
2 x LAN cable
15.0 Enclosed VESA Mount PC 486-0007-00-04
6
Page 7
* Only one USB cable per order provided. Please inquire about additionally needed usb cables during
ordering.
BEFORE MAKING ANY CONNECTIONS OR APPLYING POWER,
FIRST READ THROUGH THE ENTIRE MANUAL
Mounting Procedure
VESA Panel Mounting Procedure:
1- Install the enclosure to a 100mm VESA mount pedestal.
2- Secure the enclosure using the screws and lock washers, supplied with the unit.
3- Tighten all mounting hardware to a torque of 15 inch-pounds.
ATTENTION: Mounting hardware must be tightened to a torque of 15 inch-pounds to provide a
proper panel mount and avoid potential damage. Vartech Systems assumes no responsibility for
water or chemical damage to the monitor or other equipment within the enclosure due to
improper installation.
4- Attach the power and system cables to the bottom side of the enclosure if you have not
already done so.
15.0 Enclosed VESA Mount PC 486-0007-00-04
Product Drawing: Detail –A–
7
Page 8
Connections to the Enclosed PC
Power Connection (Power In)
The Enclosed VESA Mount PC includes an AC line cord which is 6ft long. The power input
receptacle is located on the bottom rear panel of the system.
Serial Connections (COM 2 - 3)
The Enclosed VESA PC is supplied with a serial connector configured for RS-232. The
connector is a 9 pin female connectors and can be set up for any baud rate from 300 to 19.2
baud. The connector is located on the bottom panel of the system.
Ethernet Connections (LAN)
The Enclosed PC is supplied with integrated Ethernet. The interface will support 10/100/1000
BaseT connection to a local area network (LAN). The Enclosed PC is supplied with a RJ-45
female connector located on the bottom panel of the system.
USB Connections (USB 1 - 2 - 3)
Bottom Rear View
- Connector Panel -
15.0 Enclosed VESA Mount PC 486-0007-00-04
8
Page 9
The Enclosed VESA PC is supplied with three USB 2.0 connectors, which are located on the
bottom panel of the system.
Turning the system On and Off
Before connecting the Enclosed VESA Mount PC to power, connect any peripheral devices. As
a general rule, any peripheral device should only be connected or disconnected when the
Enclosed PC is off with the exception of any USB peripheral.
The Enclosed VESA Mount PC is turned on using the main On-Off switch located on the bottom
panel. Once the Enclosed PC is powered on the computer power pushbutton switch must be
depressed for Windows to start. Windows must be properly shut down before the main power
switch is turned off to prevent the chance of corrupting files in the operating system.
The Enclosed VESA Mount PC is rated for continuous duty. However, to extend the life of the
various components and conserve power, it is highly recommended that the system be properly
shut down and power turned off when the Enclosed VESA Mount PC is not in use.
LCD Monitor Warm-up Time
All LCD monitors need time to become thermally stable the first time you turn them on.
Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to
warm (be on) for at least 20 minutes before making any screen adjustments.
Maintenance
The Enclosed VESA Mount PC is designed to provide optimum service and performance with
minimal maintenance including the occasional external cleaning. For cleaning the Enclosed
VESA Mount PC enclosure follow the suggested guidelines.
General – NEVER use abrasive cleaners or solvent-based cleaners!! Use a clean soft cloth.
The Enclosed VESA Mount PC should only be opened and serviced by a qualified technician.
Keep the area around the Enclosed VESA Mount PC clear and free of excessive dirt or other
contaminants.
For Additional Assistance
Contact Your VarTech Sales Representative
Vartech Systems, Inc.
11529 Sun Belt Ct.
Baton Rouge, LA 70809
800-223-8050
15.0 Enclosed VESA Mount PC 486-0007-00-04
9
Page 10
Fax: 225-297-2440
www.vartechsystems.com
15.0 Enclosed VESA Mount PC 486-0007-00-04
10
Loading...