Page 1
Solutions for Demanding Applications
VarTech Systems Inc.
Industrial CRT and Flat Panel Displays
VT190 DiamondVue Series
19.0” Flat Panel Series LCD Monitors
VT190C · VT190P · VT190R
VT190P-SS · VT190W · VT190M
Transflectives:
VT190PTSR · VT190PTSRSS
VT190RTSR · VT190WTSR · VT190MTSR
User’s Guide
Read these instructions completely before attempting to operate your new Color Display.
VT190 DiamondVue User Guide 150-065
Page 2
Table Of Contents
Section Page Section Page
Section 1
Introduction
Section 4
Touch screen
1.1 About LCD Monitors 1 4.1 Touch Screen Introduction 10
1.2 Product Safety Precautions 2 4.2 Touch Screen Definition 10-11
4.3 Touch Screen Serial Interface 11
Section 2
Display Setup
4.4 Setting up the Touch Interface 11
4.5 Installing Windows NT 4.0 Touch Drivers 12
2.1 Display Features 3 4.6 Installing Windows 95/98 Touch Drivers 12-13
2.2 Unpacking The Display 4 4.7 Installing Windows 2000 Touch Drivers 13
2.3 Included Parts 4
2.4 Connecting Your Display 4
2.5 Signal Connections 4-6
Section 3
Getting Started
Section 5
Troubleshooting Tips
Section 6
Cleaning & Maintenance
14-15
16
3.1 Adjusting the Display 7
3.2 Adjustment Procedure 8-9
Section 7
Mechanical Drawings
Panel Mount Instructions 17
Chassis Mount Mechanical Drawings
Panel Mount Mechanical Drawings 18-19
Rack Mount Mechanical Drawings
Wall Mount Mechanical Drawings
Section 8
Display Specifications
20
Page 3
1.1
Section
INTRODUCTION
INTRODUCTION
1
About LCD Monitors
What you gain by using an LCD monitor in your industrial controls
are the future of display technology. CRTs although they have dropped
in cost significantly, do not offer the performance, reliability, and
LCDs
LCDs
LCDs
the function of the video board which converts the analog RGB (Red, Green, Blue) signals from a
standard video card to a high quality, digital RGB that the LCD can display.
Recently the video card has taken on a new role. It is the responsibility of this device to “scale” a
particular video resolution to the “native” resolution of the LCD. Simply, consider that a computer is
putting out a VGA [640x480] resolution signal, yet the LCD that is connected is an XGA
[1024x768] display. The displayed picture would be in the center 1/3 of the LCD. With the
introduction of the scaling engine. The converter will mathematically recalculate the 640x480 to
1024x768. This may sound simple but it is in fact a complex algorithm that adjusts for different
aspect ratios and pixel alignment, essentially smoothing text and graphics to produce a picture
that is pleasant to the eye.
mounting options available with LCDs. LCD monitors consist primarily of
an LCD, Video Board and a Back Light video. The LCD determines to a
large extent the viewing angle, brightness and contrast. Beyond that it is
All Vartech displays from 12.1” (800x600) to 23.1 (1600x1200) incorporate scaling engines in the
converter card.
VT190 DiamondVue User Guide 150-065
1
Page 4
1.1
Product Safety Precautions
⇒ Ensure that sufficient space is available around the display to provide the circulation
necessary for cooling.
⇒ Ensure that the ambient air temperature will not exceed the specified maximum
temperature.
⇒ Do not attempt to service this display yourself. The rear chassis has a seal so that non
qualified personal will not expose themselves to dangerous voltages or other risks.
⇒ To protect from electrical shock, unplug the display power supply from the wall before
moving.
⇒ Do not expose the display to direct sunlight or heat.
⇒ Do not use this display near water
⇒ Do not place any heavy objects on the power cords. Damage may cause electrical shock.
⇒ Unplug the power supply from the wall or unit if one of the following conditions exists.
⇒ Power cord or plug is damaged or frayed
⇒ Liquid is spilled into the display or the display is exposed to rain or water.
⇒ The display does not operate normally when the operating instructions are
followed.
⇒ The display has been dropped or the enclosure has been damaged.
⇒ The display exhibits a distinct change in performance, indicating a need for
service.
2
Page 5
Section
DISPLAY SETUP
DISPLAY SETUP
2
VT190 Series Display Features
2.1
⇒ Capable of displaying unlimited colors in a continuous spectrum. The high contrast LCD
enhances the image with no geometric distortion.
⇒ The VT190 DiamondVue Series directly accepts an analog 5 wire RGB with separate H/V sync
or 4 wire RGB with separate combined sync or 3 wire SOG.
⇒ The VT190 DiamondVue Series is auto synchronous adjusting the display to the appropriate
input between VGA, SVGA,XGA, and SXGA.
⇒ The VT190 DiamondVue Series is available in Panel Mount, Rack Mount, or Wall Mount
industrial packages.
⇒ The VT190 DiamondVue Series is supplied with a Anti-Reflective Screen unless equipped with
an optional Touch System.
⇒ The VT190 DiamondVue Series has an integrated 115/220VAC supply as standard on all
models.
VT190 DiamondVue User Guide 150-065
3
Page 6
Unpacking and setting up your display
2.2
Your LCD monitor package will consist of the components listed below. Open shipping
container and lay all components on a flat clean surface.
2.3
What is included with your display
VT190R, VT190P, VT190C, VT190W or VT190M LCD Monitor
⇒
⇒ 5 ft Video Cable
⇒ 10-32 Mounting Hardware. (For use with Panel Mount only)
⇒ 6 ft RS232 Touch Interface Cable (Optional when touch is installed)
⇒ CD ROM with Touch Screen Drivers (Optional when touch is installed)
⇒ Users Guide (Printed or on CD)
2.4
Connecting the Display
1. Connect all cables to the computer first. This would include the VGA cable and the optional
RS 232 serial touch screen connection.
2. After connecting the cables between the LCD monitor and the computer, plug the power
cord into the 115/220VAC power outlet.
3. Once the 115/220VAC connection is made, the display is active.
4. If your computer was off, turn on your computer.
5. Your display should now operate as a normal computer display showing your windows or
whatever video is being sent to the flat panel.
Note: If for any reason the display goes blank and gives an “out of Range” or “No Input Signal”,
your computer or video source is putting out a signal that is out of range of the LCD’s video
board. If this happens, reboot the computer or video source and make sure you are inputting
the correct signal. If the display doesn’t work properly, it may be because:
(a) The resolution is to high or low for the LCD.
(b) The refresh rate is set to high. Refresh on an LCD is different than a CRT. Set the refresh to
60Hz. CRT’s need a high refresh rate to avoid flicker. The refresh rate has no impact on
LCD’s.
(c) The power source is incorrect.
(d) The unit is malfunctioning. If you believe this to be true, disconnect the video cable from the
rear of the LCD and connect to a known good computer CRT display. If the computer
display is working satisfactory and the video is within the appropriate range, then contact
Vartech Customer service for a RMA number at 800-223-8050.
2.5
Signal Connections
To avoid irregular operation and /or damage to the display, please insure correct video is being
supplied as shown on the following page.
4
Page 7
2.5
Signal Connections Cont.
You can use an HD-15 connector cable or a BNC adapter cable to connect the flat panel
monitor to the host computer. The HD-15 video cable (supplied in the kit) you use with this
monitor is equipped with a conventional HD-15 connector at each end.
Note: The following figure is the view looking into the pin end of the male connector or solder
term end of the female connector.
HD15 Connector
The following table provides the pin numbers and corresponding pin assignments for
the HD-15 video connector.
Pin Signal Pin Signal Pin Signal
1 Red Video 6 Red Video Ground 11 Not Used
2 Green Video 7 Green Video Ground 12 Bi-Directional Data
3 Blue Video 8 Blue Video Ground 13 Horizontal Sync
4 Not Used 9 No Connection 14 Vertical Sync
5 Return 10 Sync Ground 15 Data Clock (SCL)
DVI-I
C2
C1
Pin Signal
C1 Analog Red
C2 Analog Green
C3 Analog Blue
C4 Analog H. Sync
C5 Analog Ground
HD15 Connector
1
9
17
DVI-I Connector
(Digital / Analog)
8
16
24
C5
C4 C3
DVI-I
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0-
2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+
3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield
4 T.M.D.S. Data4- 12 T.M.D.S. Data3- 20 T.M.D.S. Data5-
5 T.M.D.S. Data4+ 13 T.M.D.S. Data3+ 21 T.M.D.S. Data5+
6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield
7 DDC Data 15 Ground (return for +5V, H. Sync and V. Sync) 23 T.M.D.S. Clock+
8 Analog Vertical Sync 16 Hot Plug Detect 24 T.M.D.S. Clock-
Composite Video Input Connector: CVBS 1.0V p-p
S-Video: S-VHS
LUMA Signal Input 0.7V p-p
CHROMA Signal Input 0.7V p-p
VT190 DiamondVue User Guide 150-065
5
Page 8
2.5
Signal Connections Cont.
Optional BNC Adaptor Cable
A 5BNC-to-HD15 adapter cable is available. The functions of the cables are described below.
⇒ R, B, and G: Red, Green, and Blue input connectors to establish color.
These are used for RS-343 analog signals.
⇒ HS/CS: Separate horizontal/composite sync signal from the video
source.
⇒ VS: Separate vertical sync signal from the video source.
BNC Adapter Cable
This table describes the signal types you can use with the connectors:
BNC Signal Types
BNC Signal Type Description R G B HS/ CS VS
Sync-on-Green
(Not Available)
Composite Sync
(Not available)
Separate Horizontal
and Vertical Sync.
Use the three video connectors.
Horizontal and vertical syncs are
supplied on the green video line.
Use the three video connectors
plus the horizontal sync/
composite sync input
Use the three video connectors
plus the horizontal sync/
composite sync and vertical sync
input.
X X X
X X X X
X X X X X
6
Page 9
Section
GETTING STARTED
GETTING STARTED
3
3.1
Adjusting the display
The VT190 DiamondVue Series display has an embedded microprocessor in the converter card. Once
you have the unit displaying the resolution you desire for your application do the following:
Definition of OSD (on screen display) Adjustments
3.2
On Screen Display
Major Category Adjustment Category
POWER
MENU
SEL
DOWN
UP
▼
▲
INPUT
Accessing the Menu System
1. With the OSD off, push the MENU button to activate the main OSD menu.
2. Use the UP or DOWN buttons to move from one function to another. As you move from one icon to
another, the function name changes to reflect the function or group of functions represented by that
icon. Please refer to the following clause on the next page to view a complete list of all the functions
available for the driver board.
3. Pres the SEL button once to activate the highlighted function, use the UP or DOWN buttons to se-
lect the function.
4. After selecting a function, use the ▼ or ▲ buttons to make optimum adjustments. The setting bar
moves and the numeric value indicator changes to reflect your adjustements.
Note:The numeric value indicator is provided as a point of reference only and has nothing to do with
a real measurement.
5. Press the MENU button once to return to the main menu to select another function or press twice to
exit from the OSD.
Turns the systems ON/OFF
Activates the OSD menu or goes to the previous menu
• When the OSD menu is off, press more than 3 seconds
Performs “auto-adjustment’ function
• When the OSD menu is on
Selects the highlighted icon that the user wants.
• Moves the highlight icon up to the function that the user wants
• Moves the highlight icon down to the function that the user want
•
Decreases the adjustment of the selected function
Increases the adjustment of the selected function
•
• Selects the Input Signal among analog RGB, Digital DVI, CVBS and S-VHS
VT190 DiamondVue User Guide 150-065
7
Page 10
3.3
Adjustment
Adjustment (PC)
OSD Agent Description
Adjustment is used to
fine tune and get the best
image by removing
noises that creates
unstable images with
jitters and Shimmers.
Adjustment (DVI)
OSD Agent
This function is active if
you select a digital DVI
source.
Adjustment (Video)
OSD Agent
This function is active if
you select an input
source other than PC.
(DVD, VCR)
Brightness
Contrast
Clock
Phase
Auto Adjust
Brightness
Contrast
Brightness
Contrast
Color
Adjusts the brightness of video
Adjusts the contrast of video.
Removes the noises. When frequency value is
wrong, the image has horizontal lines especially in
1 dot on and off.
Removes the noises. When phase value is wrong,
the image has vertical lines especially in 1 dot on
and off.
“Auto adjustment” allows the monitor to self-adjust
to the incoming video signal. The values of phase,
frequency and position are adjusted automatically.
Description
Adjusts the contrast of image.
Adjusts the brightness of image.
Description
Adjusts the brightness of video
Adjusts the contrast of video
Changes the richness of color
Tint
Sharpness
Changes the tone of color
Adjusts the sharpness of video image
8
Page 11
3.3
Adjustment Cont.
Color
OSD Agent
Description
The color can be
changes from redish to
bluish white.
Setup
OSD Agent
Setup is used to adjust
OSD menu information
and image.
6500º K
9300º K
User
Image
OSD
Redish white
Bluish White
User Customizable
Description
• H Position: Adjusts the horizontal position of
the image.
• V Position: Adjusts the vertical position of the
image.
• GAMMA: Bypass
• Information: Displays current display mode.
• Language: English, Germany, French, Italian,
Spanish
• Color: Change the opaqueness of the OSD
background.
• Position: Move the OSD Window
• Duration: Indicates time until the OSD Menu
will disappear after adjusting the menu.
• OSD Lock: Avoids OSD control except HOT
key.
Audio
OSD Agent
This function is
automatically activated
by connecting the
external audio board.
Mode Recall
Backlight
Auto Sleep
Volume
Bass
Treble
Mute
Changes the image information to factory outgoing
status.
Changes the brightness of image by controlling the
backlight of panel.
Goes to soft power off after 10 minutes when input
cable is disconnected.
Description
Controls the volume of sound
Controls the low frequency band of sound
Controls the high frequency band of sound
Controls the sound on/off
VT190 DiamondVue User Guide 150-065
9
Page 12
4.1
4.2
Section
TOUCH SCREEN
TOUCH SCREEN
4
Touch Screen Introduction
Touch screen interfaces have become the standard interface in the past 5 years. They are,
rugged, reliable, extremely flexible and easier than ever to implement! Over 90% of the
display packages Vartech Systems builds are touch screen systems. If you are uncertain
about using a touch screen, or are having difficulty, please call us. The universal acceptance
of the Windows GUI [Graphical User Interface] along with the extensive use of a mouse
interface has significantly accelerated the use of touch interface. Basically think of your touch
screen as if it were a mouse.
Touch Screen Definition
Quite simply, Vartech Systems touch systems are a mouse emulator. By installing a software
driver and connecting to a serial port, the touch screen will support all the primary mouse
functions:
Our standard touch screen interface, is a high resolution analog resistive. Following is a quick
explanation of what all this means.
High Resolution:
Analog Resistive: The actual touch glass is an analog device. Meaning there is a very low
voltage applied to the X and Y axis of the touch screen. This current is applied to ITO [Iridium
Tin Oxide] that is sputtered onto a polyester membrane. When you touch the screen you are
changing the resistance on both the X and Y axis, producing an analog value that references
a particular location.
This type of screen can be activated with a gloved finger or mechanical stylus.
The touch screen itself is connected to electronics that provide the Analog to Digital
conversion. When the screen is touched, the electronics convert the analog voltage to a
digital value and add a “Mouse Click”, then sends the data to the serial port that the driver is
loaded to. When the touch is released the new XY location is sent along with a “Mouse Up
Click”.
This system requires no special software knowledge, and can be installed and set up in
minutes. The following section gives a detailed explanation of the software setup and
configuration.
Since the touch screen interface is RS-232, the recommend maximum distance from the PC
is 50 feet. In reality, every application is different. The touch driver default baud rate is 9600,
and we have tested the driver and interface with good quality cables to 50 feet.
With RS-232 line drivers this can be extended almost indefinitely.
The touch screen resolution is 400 ppi [points per inch]
10
Page 13
4.2
4.3
Touch Screen Definition Cont.
Connecting the touch screen
1. Make sure all optional cables have been received.
2. Connect one end of the 6 foot touch screen serial cable to the touch screen port D9
connector on the side of the monitor.
3. Connect the other end to any communications port on the host computer.
4. Tighten the captive screws on the cable connector to secure it.
Touch Screen Serial Interface
All touch controllers are configured by default to provide serial communications at 9600 baud,
8 data bits, 1 stop bit, no parity. For Vartech flat panels equipped with touch screens, a serial
communications cable is required. This 6 foot cable comes with the unit in the accessory kit.
The cable is a straight wired serial (RS-232) cable with a male
DE-9 D-shell connector on the monitor end. The cable provides a communications channel
between the touch screen controller, which is mounted inside the monitor, and an RS-232
serial port on the host computer.
Because the touch controller obtains power from the monitor's power supply, no external touch
power connections are necessary.
Software supplied with the touch screen must be loaded on the host computer to handle
communications with the touch controller over the channel.
Because the touch screen emulates a mouse, there may be compatibility issues involving how
the touch screen emulates mouse buttons, especially multiple buttons.
4.4
Setting up the Touch Screen Interface
Enabling the Touch Screen Interface
The Flat Panel Monitor provides a female DE-9 connector for the touch interface.
This connector provides the serial interface for the touch controller.
Interconnecting wiring to the host serial port connection is shown in the following table.
Touch screen Interface
Monitor
(DCE Device)
DE-9 (Female)
1
2
3
4
5
6
7
8
9
Signal Description
DE-9 (Male) DB-25 (Male)
Not Connected (DCD)
Transmit Data (TXD)
Receive Data (RXD)
Data Terminal Ready (DTR)
Common Signal Return (SG)
Not Connected (DSR)
Request To Send (RTS)
Clear To Send (CTS)
Not Connected
Host (DTE Device)
1 8
2 3
3 2
4 20
5 7
6 6
7 4
8 5
9 22
VT190 DiamondVue User Guide 150-065
11
Page 14
4.5
Installing Touch Screen Driver Windows NT 4.0
1. Start your computer.
2. Insert the MonitorMouse for Windows NT disk into drive A.
3. Click the Start button then click Run.
4. Type “a:\setup” in the space provided and press Enter.
5. Follow the directions on the screen.
6. MonitorMouse for Windows NT provides two Installation options. Most users
should select Typical (the default) and click Next to continue. Custom allows
you to install the sample touch screen programming files.
7. The Touch screen Setup dialog box will appear. Specify the type of
touch screen controller you are using and how it is connected. Also specify the
language you want to use in the Touch screen Control Panel. Click OK to
confirm that the Setup is correct.
8. Complete the Setup program.
9. Shutdown and restart Windows NT. Continue the steps on the next page.
10. Click the Start button, then click Settings, then click Control Panel.
11. Double-click Elo Touch screen to run the Touch screen Control Panel.
12. Click the Calibrate button and touch each of the three targets as they appear
on the screen. Touch Yes when the cursor lines up correctly with your finger.
Touch OK to close the Touch screen Control Panel.
Note:
If at any time the screen cursor is not directly under your finger on a touch, the touch screen
can be re calibrated at anytime by going to the Windows control panel and selecting the Elo
Icon and selecting Calibrate.
4.6
Installing Touch Screen Driver Windows 95/98
Start your computer.
2. Insert the MonitorMouse for Windows 95 disk into drive A.
3. Click the Start button then click Run.
4. Type “a:\setup” in the space provided and press Enter.
5. Follow the directions on the screen.
6. MonitorMouse for Windows 95 provides two installation options. Most users should select
Typical: (the default) and click Next to continue.
Custom: allows you to install the sample touch screen programming files.
7. The Touch screen Setup dialog box will appear. Specify the type of touch screen controller
you are using (Serial SmartSet Model 2210) and how it is connected.
Click OK to confirm that the Setup is correct.
8. Complete the Setup program.
9. Restart Windows 95.
10. Click the Start button, then click Settings, then click Control Panel.
12
Page 15
4.6
4.7
Installing Touch Screen Driver Windows 95/98 Cont.
11. Double-click Elo Touch screen to run the touch screen control panel.
12. Click the Calibrate button and touch each of the three targets as they appear on the
screen.
13. Click yes when the cursor lines up correctly with your finger. Click OK to close the touch
screen control panel.
Note: If at any time the screen cursor is not directly under your finger on a touch, the touch
screen can be calibrated at anytime by going to the Windows control panel and selecting the
Elo Icon and select Calibrate.
Installing Touch Screen Driver Windows 2000
1. Start your computer.
2. Insert the MonitorMouse for Windows 2000 disk into drive A.
3. Click the Start button then click Run.
4. Type “a:\setup” in the space provided and press Enter.
5. Follow the directions on the screen.
6. MonitorMouse for Windows 2000 provides two Installation options. Most users
should select
Typical (the default) and click Next to continue.
Custom allows you to install the sample touch screen programming files.
7. The Touch screen Setup dialog box will appear. Specify the type of
touch screen controller you are using and how it is connected. Also specify the
language you want to use in the Touch screen Control Panel. Click OK to
confirm that the Setup is correct.
8. Complete the Setup program.
9. Shutdown and restart Windows 2000. Continue the steps on the next page.
10. Click the Start button, then click Settings, then click Control Panel.
11. Double-click Elo Touch screen to run the Touch screen Control Panel.
12. Click the Calibrate button and touch each of the three targets as they appear
on the screen. Touch Yes when the cursor lines up correctly with your finger.
Touch OK to close the Touch screen Control Panel.
Note:
If at any time the screen cursor is not directly under your finger on a touch, the touch screen
can be re-calibrated at anytime by going to the Windows control panel and selecting the Elo
Icon and selecting Calibrate.
Note: For latest touch information, refer to www.elotouch.com
VT190 DiamondVue User Guide 150-065
13
Page 16
Section
TROUBLESHOOTING
TROUBLESHOOTING
5
Troubleshooting
Trouble Troubleshooting Tip
No Picture ⇒ The signal cable should be properly connected to the
display card and computer.
⇒ Try disconnecting the video cable from the display and
connecting to a CRT display if available to confirm the
presence of proper video.
⇒ Make sure power is connected to the proper DC or AC
source.
⇒ Make sure the resolution mode is supported by the display and
check settings of the display card.
⇒ Confirm that the video cable is not defective.
Image Persistence Image persistence occurs when a ghost of an image remains on
the screen after the monitor has been turned off. Unlike a CRT
monitor, an LCD monitor’s image persistence is not permanent.
To erase an image ghost, turn the monitor off for as long as the
image was displayed. If the image was on for one hour and the
ghost of the image remains, the display should be turned off for
one hour to erase the image. To avoid this problem, use a screen
saver.
Picture Quality & Image Stability ⇒ Check for proper video cable for proper grounding and
shielding.
⇒ Check the signal source for proper signal.
⇒ Check for proper adjustment of the Phase and Frequency
controls.
⇒ Check for proper recommended signal timing.
Green LED not lit Check for proper power and power connections
Green LED blinking This indicates absence of video or proper video for this display
Display image is not properly
sized
⇒ Adjust the Vertical and Horizontal size controls via the OSD.
(Reference setup adjustments)
⇒ Ensure that a supported mode is selected on the display card
or system being used. Consult the display card or system
manual for proper video.
No S-Video or NTSC operation ⇒ Check for proper connections.
If these tips do not solve your problem, contact Vartech Systems Customer Service support.
⇒ Check the setup instructions for proper input selection.
14
Page 17
Troubleshooting Cont.
Trouble Troubleshooting Tip
Screen is blank. Screen saver activated.
Video Cable problem. Check for proper installation
Change video cable .
Faulty video display. Needs Service.
Image is dim, even with
brightness and contrast
controls set full UP
Video cable problem. Check for proper installation of cables
Faulty video source.
Faulty display.
Image not centered Reset the horizontal and vertical positioning using the on-screen
menu. Check to see if video source is operating within the
monitor’s range
Image will not adjust Video timing outside of range. Use the on-screen menu to ad
just the Clock Setting.
Make sure timing is within VESA standard.
Image is not stable. Monitor has incorrect or bad sync signals.
Check for proper video cable installation.
Replace suspected faulty cable.
Check to ensure that video source is operating within the display’s
range.
Vertical shaded bars on
Screen image
Horizontal size not properly adjusted.
Adjust horizontal size settings
Colors are missing Faulty video cable.
Missing from video source.
Connect video source to another display
Screen jitter or noisy display
Slight distortion in text or
Monitor clock phase not properly adjusted
Not working in native resolution.
Graphics.
Display is present but “bars”
Appear or roll across screen
The background looks
Ground loop problem between computer and display
Interference from adjacent equipment
Video running interlace mode.
Acceptable but text and
Icons seem to be missing
rows of pixels
15
VT190 DiamondVue User Guide 150-065
Page 18
Section
CLEANING AND MAINTANENCE
CLEANING AND MAINTANENCE
6
Cleaning
Occasionally clean the display panel and cabinet with a soft cloth dampened (not soaked) with a
mild (non-abrasive) glass cleaner. Keep turning a fresh side of the cloth toward the screen surface to
avoid scratching it with accumulated grit.
Note:
The solvent should be applied only to the cloth, and not directly on the monitor screen.
Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow
the screen to stand dry.
Special care should be taken when cleaning a touch screen or polycarbonate shield that is installed
over the screen. Abrasive and certain chemical cleaners can easily damage the surface.
Never use alcoholic or ammoniac cleaners to clean the polycarbonate shield or a touch screen.
Note:
For best results cleaning a monitor with the optional antireflective tempered glass display shield, a
solution of denatured alcohol is recommended to thoroughly clean the display.
Replacing a Line Cord
To avoid shock and fire hazards, the monitor’s power cord should be replaced if the insulation
becomes broken or if it develops a loose internal connection.
Other Maintenance
Qualified service personnel should perform all maintenance, except for the power cord replacement
described above.
16
Page 19
Section
MOUNTING INSTRUCTIONS
MOUNTING INSTRUCTIONS
7
Mechanical Drawings
Model Description Page(s)
VT190P 19.0” Panel Mount Mechanical Drawing 18-19
VT190R 19.0” Rack Mount Mechanical Drawing
VT190W 19.0” Wall Mount Mechanical Drawing
VT190M 19.0” Tabletop Mechanical Drawing
VT190C 19.0” Chassis Mount Mechanical Drawing
7.1
Panel Mount Procedure
Panel Mounting Procedure
1. Cut and drill the panel (refer to panel mount drawing). Measurements are in inches.
Panel Mounting Cutout
2. If access to the side of the monitor is not available following installation, attach the power and video
cables to the side of the monitor at this time.
3. Install the monitor in the prepared cutout.
4. Install the lock nuts and washers, supplied with the monitor, behind the holes running along the sides
and top/bottom of the cutout in the panel. Extra lock nuts and washers are provided.
Note:
Use #10-32 nuts for mounting.
5. Tighten all mounting nuts evenly to a torque of 24 inch-pounds.
ATTENTION: Mounting nuts must be tightened to a torque of 24 inch-pounds to provide panel seal and
avoid potential damage. Vartech Systems assumes no responsibility for water or chemical damage
to the monitor or other equipment within the enclosure due to improper installation.
6. Attach the power and video cables to the side of the monitor if you have not already done so.
VT190 DiamondVue User Guide 150-065
17
Page 20
Section
8
ENGINEERING SPECIFICATIONS
Panel Size 19.0”
Type TFT Active matrix w/ Anti-Glare coating
Resolution Capabilities VGA to SXGA
Pixel Pitch 0.294mm
Active Display Area
Pixel Format 640 x 480, 800 x 600, 1024 x 768, 1280 x 1024
Viewing Angle (Left/Right) 85/85º
Viewing Angle (Up/Down) 85/85º
14.81” x 11.85”
376.3mm x 301.06mm
SPECIFICATIONS
SPECIFICATIONS
Contrast Ratio 500:1
VT190P, VT190PSS, VT190R, VT190C, VT190W, VT190M:
Brightness
Response Time
Back Lights Cold Cathode 50,000 Hrs. Half Life
Video Connector
Colors Supported 16.7M
Video Input
Sync
Input Voltage AC 100-240V 50/60Hz 1.0A
250 Nits
Transflectives:
over 1000 Nits*
T
= 15ms typical
R
T
= 10ms typical
F
HD15(F)
DVI-I 29Pin connector (Digital/Analog)
Composite Video (CVSC)
S-Video (S-VHS)
RGB Analog (0.7V p-p / 75ohm) , Digital
CVBS (1.0V p-p)
S-VHS, luma/chroma (.7V p-p / 75ohm)
Separate H&V, Combined,
SOG (Sync On Green), Digital
Power consumption Normal: 70Watts DPMS: < 3Watts
Operating Temperature 0 to 50ºC
Storage Temperature -20 to 60ºC
Operating Humidity 10 to 95%NC
Storage Humidity 10 to 95%NC
Operating Altitude Up to 10,000 ft
Storage Altitude Up to 40,000 ft
*Outdoor Brightness Equivalent (Varies depending upon sunlight brightness)
20
Page 21
VARTECH SYSTEMS
HEADQUARTERS
11529 Sun Belt Ct.
Baton Rouge, Louisiana 70809
Toll-Free: 800.223.8050
International Phone: 001.225.298.0300
Fax: 225.297.2440
E-mail: sales@vartechsystems.com
www.vartechsystems.com
VT190 DiamondVue User Guide 150-065
150-065-001
8.23.04
Loading...