Varta V-HF42LP User Manual [ru]
Руководство по эксплуатации
Instruction manual
V-HF42LP
РАДИОПРИЕМНИК С
БУДИЛЬНИКОМ
RADIO WITH ALARM
Instruction manual
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for reference in the future.
DESCRIPTION
1. UP button
2. MODE button
3. SET button
4. VOL+ button
5. Lampshade
6. Brightness regulator
7. SNOOZE switch
8. DOWN button
9. LAMP button
10. Display
11. NATURE button
12. VOL- button
1 2 3 4
5
6
Not indicated:
Back of the unit: Power cord, Speaker, FM
antenna
Bottom of the unit: Battery compartment, RESET button
IMPORTANT SAFEGUARDS
• Attention: The owner’s manual contains
important operating and maintenance instructions. For your safety, it is necessary to refer
to the manual.
• Dangerous voltage: Uninsulated dan-
gerous voltage that may be of sufficient magnitude to constitute a risk of electrical shock
to persons is present within this product enclosure.
• Caution: To reduce the risk of electric
shock, do not dismantle the body. Prefer servicing to qualified service personnel. Do not
use the unit in places where it can be exposed
to water, moisture and dust. Make sure that
pins or other foreign objects do not get inside
the unit; they may cause malfunctions, or cre-
2
7
8 9 10 11 12
ate safety hazards such as electrical shock.
• Lamp: Before using a new halogen lamp
for this product, please turn off the power. Do
not use compact fluorescent bulbs or electronic ballast bulbs. The old bulb should be
replaced with a bulb having the same technical specifications.
CHANGING THE LAMP
• Screw off the screw on the left side of
the lampshade. Take off the lampshade.
• Turn down the halogen lamp and change
it to a new one.
• After mounting the lampshade fasten
the screw on the left side.
www.varta-electronics.ru
Instruction manual
POWER SUPPLY
Battery operation
• Open the battery compartment cover.
• Insert 2 batteries 1.5 V (UM-2/AAA).
Please observe correct battery polarities or
the set will not work.
• Close the battery compartment cover.
• This is additional power intended for
sustainability maintenance of memory of clock,
alarm and calendar.
AC operation
• Before the first connecting of the ap-
pliance check that voltage indicated on the
rating label corresponds the mains voltage in
your home.
• Insert the plug into power supply.
• When the set is not used for 2 weeks
or more, please remove the batteries, to avoid
damage to the set from leakage of batteries.
• Always switch off the unit when not in
use.
• Always unplug the appliance from pow-
er supply, when not in use long time.
GENERAL OPERATIONS
• After the unit is powered on, the unit
will be in clock mode, and the display will show
current time in 12-hour mode, year, month and
date.
• To select 12-hour or 24-hour clock
mode, press UP button.
• In the FM-radio or when sounds of na-
ture are playing, press VOL+/- buttons to adjust
the volume of the sound. The volume level will
be displayed in figures (1-20) and as a bar.
• Press LAMP button to switch the lamp
on. You can adjust its brightness by rotating
the Brightness regulator. The brightness level
will be displayed in figures (1-18) and as a
bar.
• Press and hold LAMP button to switch
off the display backilght. Press and hold LAMP
button again to turn the backlight on.
• Press NATURE button to switch on na-
ture sounds. The bird icon will be displayed.
You can select any of 7 available sounds by
pressing UP/DOWN buttons. The sound number will be displayed.
• Press RESET button to reset all settings
to default values (except FM radio stations).
RADIO OPERATION
• Press MODE button to switch on the FM
radio. The display will show the receiver icon,
channel number and current frequency.
• Press SET button; the frequency will
start blinking. Press and hold UP/DOWN buttons to scan for the nearest station with strong
signal. Or press shortly UP/DOWN buttons to
change the frequency step by step.
• To save the current frequency, press
SET button. The frequency will stop blinking.
• Press UP/DOWN buttons to select pre-
vious or next channels.
SETTING TIME AND CALENDAR
• In clock mode, press and hold MODE
button; the bell icon will blink. Press MODE
button twice more; the words YEAR, MONTH
and DATE will blink.
• Press SET button repeatedly to select a
parameter for setting: hour => minutes =>
year => month => date. The selected parameter will blink.
• After the parameter is selected, press
UP/DOWN buttons to set it.
• After all settings are done, press MODE
button to confirm.
ALARM OPERATION
Alarm setting
• Press and hold MODE button; the bell
icon will blink.
• Press SET button repeatedly to select a
parameter for setting: hour => minutes =>
alarm sound => snooze time => alarm sound
volume => lamp intensity. The selected parameter will blink.
www.varta-electronics.ru
3
Loading...