Varta V-GPS52G User Manual [ru]
Руководство по эксплуатации
V-GPS52G
V-GPS52G
Instruction manual
ПОРТАТИВНАЯ НАВИГАЦИОННАЯ
СИСТЕМА
PORTABLE NAVIGATION SYSTEM
Instruction Manual
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for reference in the future.
UTILIZATION OF THE PRODUCT
If you want to dispose this product, do not
mix it with general household waste. There is a
separate collection system for used electronic
products in accordance with legislation that
requires proper treatment, recovery and recycling.
Please contact your local authorities for the
correct method of disposal. By doing so, you
will ensure that your disposed product undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative
effects on the environment and human health.
IMPORTANT SAFEGUARDS
• Please read all the instructions in this Instruction Manual carefully and use accessories provided by the original manufacturer only.
Implementing the system without conforming to
proper programs or connecting incompatible accessories may result in malfunction of this unit or
danger to the safety of you and others.
• Do not shake or knock the device. Rough
handling may lead to damage. malfunction or
missing of the data .
• Keep the device away from direct sunlight
or high temperature, to prevent overheating of
the batteries and device body which may cause
failure or danger.
• Keep the device away from moisture and
raindrops. If water gets inside, it may cause damage the device.
2
• Keep the device away from environment
of dusts.
• Operating the device near strong radio wave
or radioactive rays may affect the performance of
the device.
• Insert the plug fully into the electrical outlet
to prevent static electricity.
• Ensure that all cables are connected to the
device safely and orderly to prevent damages of
the device.
• Do not press the LCD screen hard; keep the
screen away from sunlight. Clean up dusts on the
screen surface with soft cloth.
• If the device fails, please send it to an authorized maintaineer for repair.
• Keep the device out of reach of children
when it is being charged.
• Please do not set the volume of an external
loudspeaker too high for a long time. Longstanding use may cause an output distortion of the
loudspeaker.
www.varta-electronics.ru
Instruction Manual
CONTROLLERS AND CONNECTORS
Left panel
1. Headphone jack
1
2. Memory card slot
3. AV input
2
4. MiniUSB port
3
4
Back panel
VGPS52G
ПОРТАТИВНАЯ НАВИГАЦИОННАЯ СИСТЕМА TFT5"
Номинальное напряжение питания: 5 В,
Номинальная потребляемая мощность: Вт
56 7 89
5. Stylus
6. Speaker
ТЕХНО ЭЛЕКТРИК ЛИМИТЕД
Сделано в Китае
2.5 A
12
7. SIM card slot
8. Power button (on the top edge)
9. RESET button (hole)
POWER SUPPLY
General notes
The unit can be powered in two ways, i.e. bat-
teries and MiniUSB supply.
When not connected to the charger adapter,
the unit is powered by the lithium batteries. The
power icon
system interface or the power bar
power-setting interface indicates the remaining
battery power.
When connected to the MiniUSB charger
adapter (or via MiniUSB to connect computer),
the GPS navigator is powered by the external
power.
This navigator uses a built-in, not removable
lithium polymer battery power supply. Generally,
if completely fi lled, the battery can supply power
continually about for 1.5 hours. However, some
functions (audio, video, high-luminance backlight) must consume much energy, this will reduce power supply time.
• To avoid fi re or burn danger, please
do not disassemble, pierce, collide or discard the
battery. The battery can burst, blast or release
dangerous chemical substance.
• Do not power off when you are navigating,
playing fi lms and music, and viewing pictures.
on the top right corner of the
in the
Charging with power adaptor
Used for the fi rst time or no used for a long
time, the unit must be completely charged by a
MiniUSB charger adaptor.
Connect the DC terminal of the adapter (not
included) to the MiniUSB port of the unit. Connect the other terminal to the power socket or
computer to charge and power the navigator at
www.varta-electronics.ru
3
Instruction Manual
the same time.
If the charging indicator fl ashes in red,
it indicates the unit is being charged. Wait until
the unit is completely charged. Do not remove the
adapter during charging. The indicator will fl ash
in green when the unit is completely charged.
Charge the battery in time when the power is insuffi cient or exhausted in the future.
Charging with car adaptor
Connect one end of the car adapter to the MiniUSB port of the unit. Connect the other end to
vehicle cigarette lighter to power and charge the
unit at the same time.
Plug the car adapter after the car is started
to avoid damages to the unit caused the instant
current at start time.
GENERAL OPERATIONS
Power on/off
Press and hold power button to turn on the
unit. Press power button to switch off. The system
enters sleep mode. When you switch on again,
the device will maintain the operation status last
time you switch off. Press and hold power button
to switch the unit off completely.
Using the vehicle break
A vehicle bracket is composed of a bracket
and a support. Fix the device using the vehicle
bracket onto the front windshield or dashboard
while using the unit in a vehicle.
1. Clean the fi xation surface on the windshiled
and leave it to get dry.
2. If the environment temperature is lower than
+15°C, heat the fi xation surface a little for a bet-
ter contact.
3. Install the bracket to the fi xation location:
• Tightly press the suction cup to the wind-
shield.
• Press the fi xation lever to fi x the suction cup
on the glass.
• Adjust the tilt angle of the bracket for a bet-
ter view.
4. Install the Navigator with support onto the
bracket:
• Fix the navigator to the support ensuring that
the fi xing lockers are alined with corresponding
fi xing slits on the unit cabinet.
• Fix the unit and support assembly to the
bracket placed on the windshield or dashboard.
Resetting the system
When the system has no response, press RESET button (hole) with a sharp-ended object to
restart the system.
If the system fails, you will miss the system
information not yet saved by restarting the system. Please backup the data regularly.
Using the stylus
The stylus is used to operate the unit in fol-
lowing ways:
• Click: Click the screen once with the nib.
• Double click: Click the screen twice quickly
with the nib.
• Dragging: Click one place with the nib, then,
move the nib.
The stylus with a broken nib, ballpoint
pen, as well as any sharp and rough objects may
scratch and damage the LCD screen. Use the
stylus with a nib in good condition. Do not use the
stylus if the nib is damaged.
Using the memory card MicroSD
• This unit is equipped with memory-card slot
enabling you to play media fi les contained in a
card (not included). Insert the card properly into
the slot according to the marking. Pay attention
to the slot position for inserting the card. Insert-
4
www.varta-electronics.ru
Instruction Manual
ing randomly may cause damages to the slot and
the card.
• Do not take out the card at random when the
system is running a navigation program or playing a media fi le.
For correct and satisfactory operation,
licensed MicroSD memory cards of famous
brands should be used with this unit. Avoid using
memory cards of unknown brands. Capacity: up
to 32 Gb.
CONNECTION
Connecting to computer
Access to PC enables you to copy fi les from
the navigator to the PC and vice versa or backup
the data in the navigator to the PC for future use.
• Ensure the unit is on. Connect the MiniUSB
cable to the MiniUSB port of this unit and USB
port of a PC. On completing connection, the PC
will automatically identify the new hardware unit.
• On completing communication, remove the
mini USB cable, and the unit returns to run like
before.
Please backup the system data to an ex-
ternal storing device before updating.
While accessing a PC, the following operations will interrupt the communication between
the system and the PC. Then, the unfi nished
transmission data will be missing:
1. Unplug the miniUSB cable;
2. Press power button to switch off;
3. Restart the system via RESET button.
Headphones
Connect earphone or headphone (not included) to the headphone jack of this unit. The sound
will be output through the headphone, the built-in
speaker of this unit will be muted.
Do not use an earplug with over high vol-
ume, or it will hurt your hearing and even cause
permanent hearing impairment.
Audio/video input
AV input is used for receiving audio and video
signal from an external source (back view camera or DVD player). Connect external video/audio
source to this unit with a compatible audio-video
cable (not included). When the connected external device is turned on, this unit will automatically
play its audio and video.
MAIN USER INTERFACE
When the power is on, the screen shows Main
user interface consisting of 6 touchable icons:
• NAVIGATION: Open Navigation mode.
• MULTIMEDIA
Video player: Operations with video fi les.
Audio player: Operations with audio fi les.
• PHOTO: Operations with images.
• EBOOK: Operations with TXT format fi les.
• SETTING: Set volume, power supply, backlight, date and time, languages as well as system
information.
• GPRS: Operations performed through
GPRS connection.
NAVIGATION
After you click Navigation icon, the unit enters
into GPS Navigation mode. For all operations
with GPS Navigation please read the Instruction
Manual for your GPS software.
Navigation can operate along with music playback in background mode. For this, enter GPS
Navigation mode, then briefl y press Power but-
ton to reduce Navigation mode, then start music
playback (see below). After that enable the Navigation mode again. The unit will operate as navigation whil music will be played.
www.varta-electronics.ru
5
Instruction Manual
MEDIA PLAYER
Audio player
Audio fi le playback is available only from ex-
ternal media (memory card). Press MULTIMEDIA, then click MUSIC to show track list. Click a
track to start its playback. Following interface will
be displayed:
1234 5
6 7 8 9 10 11 12
1. Audio indicator.
2. Click to show content list. In the content list
click needed fi les/folders to select them. Click
and navigation buttons to select content
pages.
3. Click repeatedly to select or cancel cycling
or random playback of fi les in the current folders.
4. Elapsed track time indicator.
5. Click to return to previous menu level.
6. Click to pause or start playback.
7. Click to stop playback.
8. Click to select previous fi le.
9. Click to select next fi le.
10. Progress bar. Drag the slidebar to select
playback time point.
11. Volume bar. Drag to adjust volume.
12. Click to return to Multimedia menu.
Image viewer
Image fi le playback is available only from
external media (memory card). Click PHOTO to
show fi le list. Click a fi le to start its playback. Fol-
lowing interface will be displayed:
12062.jpg
21345678910
1. File name.
2. Click to return to previous menu level.
3. Click to select previous fi le.
4. Click to select next fi le.
5. Click to zoom out.
6. Image window.
7. Click to zoom in.
8. Click to rotate the image.
9. Click to show content list. In the content list
click needed fi les/folders to select them. Click
and navigation buttons to select content
pages.
10. Click to return to Multimedia menu.
6
www.varta-electronics.ru
Video player
Video fi le playback is available only from ex-
ternal media (memory card). Press MULTIMEDIA, then click VIDEO to show fi le list. Click a
fi le to start its playback. Following interface will
be displayed:
12345 6 7 8
910 11 12
1. Video indicator.
2. Volume bar. Drag to adjust volume.
3. Brightness bar. Drag to adjust brightness.
4. Click to select previous fi le.
5. Click to select next fi le.
6. File name.
7. Video display window.
8. Click to return to previous menu level.
10. Click to show content list. In the content
list click needed fi les/folders to select them. Click
and navigation buttons to select content
pages.
11. Progress bar. Drag the slidebar to select
playback time point.
12. Elapsed playback time indicator.
EBook
Press EBOOK to show fi le list. Click a fi le to
start its playback. Following interface will be displayed:
Instruction Manual
12345678 910
1. Click to show content list. In the content list
click needed fi les/folders to select them. Click
and navigation buttons to select content
pages.
2. Click to select previous page.
3. Click to select next page.
4. Text display window.
5. Click to access font setting menu. In the
menu, click
size. Mark “Bold“ or “Normal“ to set the font type.
6. Click to access color setting menu. In the
menu click
or, background color and selection background
color. Drag “R“, “G” or “B” bars to change Red,
Green or Blue color balance.
7. Bookmark button. To access this option, select a text for a bookmark. Click bookmark button
and select YES to create bookmark.
8. Click to view bookmark list. In the bookmark
list click the needed bookmark, then click
skip to this bookmark, or click
bookmark.
9. Click to return to previous menu.
10. Navigation bar. Click
buttons to navigate in the text.
and buttons to set the font
and to select between font col-
to delete the
and navigation
to
www.varta-electronics.ru
7
Instruction Manual
GPRS
In the main menu click GPRS to access GPRS
menu consisting of following items: GPRS, SMS,
Phone Dial, Phone Book, Web Browse, Dial History, Setting. Click any of the icons to go to corresponding mode. Click
to exit the menu.
GPRS operations
Click GPRS to show the list of preset conection settings of various operators. Click a profi le
to select the operator. Click
selected profi le. Click
fi le. A menu will open in which you can click
icon to call the touchable keyboard. Click Country,
APN, Password, etc. lines to input corresponding
data. After the profi le is created, click
it. Click
connection by the selected profi le. Click
exit the menu.
icon to start or terminate the GPRS
icon to delete the
+ icon to create a new pro-
to save
to
SMS
Click SMS to go to SMS operation menu. The
list of SMS messages will be displayed. Click the
needed message, then click
selected message.Click
message; an interface will open, in which you can
icon to select the addressee from the
click
phone book; click
icon to call the touchable keyboard.
click
to exit the menu.
Click
Send
icon to delete the
icon to create a new
icon to send the SMS;
Phone dial
• Click Phone Dial to access phone dialling
menu. The touchable keyboard will be displayed.
Dial the needed phone number. Click
delete an erroneous symbol. Click
to the phone book. When the number is dialled,
icon to start the call.
click
• When there is a call, an interface will be
icon to
icon to go
shown in which you can adjust the volume by
clicking
(
mode of the call.
• Click
You can listen to the phone call and make conversation by the microphone situated on the front
panel of this unit. The conversation time will be
displayed. Click
icon to call the touchable keyboard. Click
exit the menu.
and icons or the volume bar
). Click icon to enable background
icon to accept an incoming call.
to cancel the call. Click
Phone book
• Click Phone Book to go to the phone book.
The phone number list will be shown. Click the
needed number to select it. Click
the selected number, click
number from the phone book. Click
display the number list contained in the SIM card.
icon to display the number list contained
Click
in the host device.
• Click
menu will open; click
able keyboard. Click
the new addressee. Click
phone number. Click
number. Click
the new account.
• You also can call the selected addressee by
clicking
icon. Click to exit the menu.
+
icon to create a new account. A
to input the home phone
to add a note. Click to save
icon or send him an SMS by clicking
icon to delete
ALL
icon to delete all
icon to call the touch to create the name of
to input the mobile
Dial history
Click Dial History to access dial history record.
to show missed call list. Click to
Click
show answere call list. Click
call list. You can also call to the selected number
by clicking
ing
number in the phone book. Click
menu.
icon or send him an SMS by click-
icon. Click + icon to save the selected
to show dialled
to exit the
to
icon to
8
www.varta-electronics.ru
Instruction Manual
Web browse
Click Web Brouse to access the web browser.
The default start page will be shown. Click
icon to call the touchable keyboard. Click
to go to the previous or next web-site. Click
to refresh the current site, click to cancel
opening or refreshing of the page. Click
quit the current interface.
and
to
GPRS setting
Click Setting to access setting menu consisting of following options: PIN, GSM, IE, GPRS,
Audio. Click any of the icons to go to corresponding setting.
• PIN: In the PIN setting menu click
to call the touchable keyboard enabling you to
enter the PIN (Personal Identifying Number) code
of the SIM card. After inputting the code, click OK
icon to confi rm. If you input PIN code incorrectly
3 times, you will have to input the PUK code provided by the service provider. After you input the
correct PIN code, the SIM card will be unlocked.
PIN Disable and PIN Enable items show the current status of SIM-card protection by PIN code.
to exit the menu.
Click
• GSM: In the GSM setting menu click to
tick ON or OFF icon to enable or disable GSM
module of phone web connection. By default the
connection is on. Click
• IE: In the IE setting page click
call the touchable keyboard enabling you to enter
the default start page of the web browser. After
inputting the code, click OK icon to confi rm. Click
to exit the menu.
• GPRS: In the GPRS setting menu click to
tick Enable or Disable icon to enable or disable
automatic GPRS connection. Click
menu.
• AUDIO: In the Audio setting menu click to
tick Earphone Mode or Speaker Mode icon to select earphone or speaker for sound output while
a phone conversation by using this unit. Click
to exit the menu.
icon
icon to
to exit the
to exit the menu.
SYSTEM SETUP
Click SETTING to access system setting menu
consisting of following items: Backlight, Volume,
Language, Date Time, Calibration, FM, GPS info,
System information, Restore settings, Power and
Navi Path. Click any of the icons to go to corresponding setting. Click
setting menu pages.
to switch between
Backlight
Click Backlight to access backlight setup
menu. In this menu click
backlight time mode. Click
the brightness of backlight; you can also click
brightness bar (
level. Click
to exit the menu.
and to select
and to adjust
) to adjust brightness
Volume
Click Volume to access volume setup menu.
In this menu click
tap sound mode. Click
sound volume level; you can also click volume
bar (
to exit the menu.
and to select screen
and to adjust the
) to adjust volume level. Click
Language
Click Language to access language menu. In
this menu click the needed language to select
the system menu language. Click
menu.
to exit the
Date and time
Click Date Time to access time setting menu.
In this menu click
and to adjust year, month, date, hour
Click
and to select time zone.
www.varta-electronics.ru
9
Loading...