Varta V-AVM700 User Manual [ru]

V-AVM700

MULTIMEDIA DVD RECEIVER WITH MOTORIZED 7” TFT DISPLAY, TV TUNER, BLUETOOTH

AND COMPATIBILITY TO GPS

МУЛЬТИМЕДИЙНЫЙ DVD-РЕСИВЕР С 7” МОТОРИЗОВАННЫМ TFT- ДИСПЛЕЕМ, ТВТЮНЕРОМ, ИНТЕРФЕЙСОМ BLUETOOTH И ВОЗМОЖНОСТЬЮ РАБОТЫ С GPSНАВИГАЦИЕЙ

Instruction manual Руководство по эксплуатации

V-AVM700

Thank you for buying our product. It is recommended to read this manual all through to avoid any failures in its work.

Contents

Contents........................................................................................................................................................................2

Important safeguards ....................................................................................................................................................4

Accessories and Hardware............................................................................................................................................5

Installation ....................................................................................................................................................................6

Controls ......................................................................................................................................................................13

Front Panel..................................................................................................................................................................13

Information on the LCD display.................................................................................................................................14

Remote control ...........................................................................................................................................................15

Basic Operation ..........................................................................................................................................................17

Radio operations.........................................................................................................................................................20

RDS operations...........................................................................................................................................................22

DISC operations .........................................................................................................................................................24

USB/SD operations.....................................................................................................................................................34

Bluetooth operations...................................................................................................................................................37

TV Tuner operations...................................................................................................................................................44

Other modes................................................................................................................................................................46

Equalizer.....................................................................................................................................................................48

Setup ...........................................................................................................................................................................50

Handling discs ............................................................................................................................................................57

V-AVM700

Troubleshooting Guide...............................................................................................................................................58

Specifications..............................................................................................................................................................59

V-AVM700

Important safeguards

• Using the device at temperature below -10º С may cause the breakage of the device. BEFORE USING

PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE!

• Read carefully through this manual to familiarize yourself with this high-quality sound system.

• Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher

amperage rating may cause serious damage to the unit.

• DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes.

• Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or create

safety hazards such as electrical shock or laser beam exposure.

• If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

• DO NOT open covers and do not repair yourself. Consult the dealer or an experienced technician for help.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or

during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified technician check the system.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please confirm it before installation.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

V-AVM700

Accessories and Hardware

No. Item Diagram Quantity No. Item Diagram Quantity

1 Remote control

2 Battery

4 Link cable

5 TV box

6 TV antenna

7 Glasses cloths

8 Assembly bars

Media Link

Box

1 9

1 10 Power cable

1 11

1 12 Rim

1 13 Manual

1 14

1 15 Warranty card

Parking

extending line

Screw/Short

bracket

Consumer

Information

V-AVM700

Installation

• Be sure to connect the color-coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle’s electrical system.

• Be sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect the left and right channel speaker cables to each other or to the vehicle body.

• Make sure all the connections are completely correct before turning on your unit.

• When replacing the fuse(s), the replacement must be of the same amperage as shown on the fuse holder.

• Do not block vents or radiator panels. Blocking them will cause heat to build up inside and may result in fire.

• After completing the installation, please press RESET button on the unit with pointed object (such as ball-

point pen) to set the unit to initial status.

• Use only the parts included with unit to ensure proper installation. The use of unauthorized parts can cause malfunction.

• Consult with your nearest dealer if installation requires the drilling or other modifications of the vehicle.

• Install the unit where it does not interfere with driver’s actions and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it overheats, so don't install the unit in hot place, for example, near a heater outlet.

V-AVM700

Control cables connections

• Auto Brightness Control To avoid the display being too bright at night time, if the cable for headlight is connected to ILLUMI, turning on the headlight dim the backlight of LCD and TFT and vice versa.

• Telephone Mute If the MUTE is connected, other audio outputs mute when a telephone call is received by the car phone.

• When Reverse Driving If a rear view camera is connected to the unit, the playing source switches to CAMERA automatically when you start reverse driving. As the reverse driving is done, the playing source switches to the last mode.

• When Parking Brake applied o If “PRK SW” cable is connected to hand brake switch, the video view to the TFT monitor will be

controlled by this function. Parking cable function ceases when the playing source is CAMERA.

o The monitor displays the blue screen with warning information to prevent the driver watching other

contents during driving, but the passengers at the rear seats can watch normally.

• TFT Monitor Protection The unit will protect the movement mechanism automatically when the monitor's movement is blocked.

V-AVM700

Installation Method A

1. Insert mounting bracket into dash board, choose appropriate mounting tab according to the gap width, bending the mounting tab outwards with a screwdriver to fix the mounting bracket in place.

2. Use 2 pieces of M5X5 cone shaped screw to fix two assemble bars on both sides of the unit.

3. Screw in 1 piece of M5X24 to the hole of the unit back and put on a rubber sheath over the screw.

4. Insert the unit into the bracket, fasten the M4X6 screw to the fireproofing board available at the back of the dashboard, and use 4 pieces of M2X2 screw to lock the assemble bars and the mounting bracket in position.

Note: According to the depth of the opening, use different length of assemble bar accordingly. If the opening is too shallow, the monitor may be extended out 10 mm from the dashboard.

V-AVM700

Installation Method В

1. Insert this unit directly to the opening of the dashboard.

2. Place M4X3, M5X5 cylindrical screw or M5X5 cone shaped screw through the holes of the mounting frame

located inside the opening to holes of the unit and fasten the screws to left and right.

Trim ring installation

Attach the trim ring around the front panel with two indentions on one side facing upwards.

V-AVM700

Uninstall

• Disassemble trim ring

1. Push the trim ring upward and pull out the upper part.

2. Push the trim ring downward and pull out the lower part.

• Disassemble the unit

1. Unscrew the 4 pieces M2X2 screws.

2. Use a screwdriver to bend straight the bended mounting tab and tip out the unit from the mounting bracket.

3. Pull out the unit from the mounting bracket with both hands.

V-AVM700

Parking brake cable connections

Reverse driving cable connections

V-AVM700

Wiring connection

V-AVM700

Controls

Front Panel

1. AS button: Auto Store

2. BAND button: Change radio band

3. VOL knob: Adjust volume/EQ

4. /SRC button: Unit power/Change work mode

5. MUTE/ button: Mute audio output/Call

6. REAR/ button: Display rear zone information/Hang-up

7. PIP button: Open Picture-In-Picture (PIP) source

8. RPT button: Change repeat modes

9. RESET button: Reset the unit

10. 5-Way cursor joystick a. Fast Forward/Move cursor UP b. Fast Reverse/Move cursor DOWN с. Auto search/Previous/Move cursor to the LEFT d. Auto search/Next/Move cursor to the RIGHT e. Play/Pause/Enter

11. EJECT button: Eject disc

12. OPEN button: Open/Close the TFT monitor

13. DISP button: Display information

14. WIDE button: Change display mode/Image Setting

15. TILT button: Change display angle

V-AVM700

Information on the LCD display

1. Disc indicator

Light up when disc is inside; Light off when no disc is inside.

2. Repeat mode indicator Light up when repeat mode is on; Light off when repeat mode is off.

3. Main display area Display characters, playback time, tuning frequency, clock and other text information; colon is an accessorial sign.

4. Radio status indicators Stereo indicator is lit up when radio broadcast is a stereo one; Local indicator is lit up when local radio station seeking is activated.

5. RDS function indicators AF: Alternative Frequency, PTY: Program Type, ТА: Traffic Announcement, TP: Traffic Program

Note: Most information is displayed when monitor is closed.

V-AVM700

Remote control

1. POWER button

2. SRC button

3. SETUP button

4. VOL+/- button

5. TITLE button

6. MUTE button

7. MENU button

8. AUDIO button

9. PRESET UP/DOWN button

10. BAND/ II► (SLOW PLAYBACK) button

11. SLIDE UP/DOWN button

12. GOTO/CALL button

13. TILT UP/DOWN button

14. RPT/A-B button

15. RPT button

16. EJECT button

17. PIP button

18. UP/DOWN/LEFT/RIGHT/ENTER cursor (joystick)

19. FRONT/REAR switch

20. ANGLE button

21. SUBTITLE button

22. PIC button

23. WIDE button

24. STOP button

25. DISP/CLEAR button

V-AVM700

26. NUMBER buttons

27. RDM button

28. SCN button

Notes of remote control using:

1. Aim the remote control at the remote sensor of the unit.

2. Remove the battery from the remote control or insert a battery insulator if the battery has not been used for a month or longer.

3. DO NOT store the remote control under direct sunlight or in high temperature environment, or it may not function properly.

4. The battery can work for 6 months under normal condition. If the remote control doesn’t work, please change the battery.

5. Use "button shaped" lithium battery "CR2025" (3V) only.

6. DO NOT recharge, disassemble, heat or expose the battery in fire.

7. Insert the battery in proper direction according to the (+) and (-) poles.

8. Store the battery in a place where children cannot reach to avoid a risk of accident.

Uninstall Battery

Slide out the battery compartment tray at the

bottom on the back of the remote control.

Install battery

Insert the battery to the battery tray with proper direction according to the (+) and (-) poles.

V-AVM700

Basic Operation

Turn on/off the power

Press SRC/POWER button on to unit or POWER button on the RC to turn the unit on. Press and hold this button to turn the unit off.

Note: You can operate the unit functions with the help of touch screen buttons.

Enter password

The password is 012345 (lf this password is not correct, please ask the dealer). You need to enter password when you use this unit for the first time or after changing the car battery. You can try 6 times when your password is wrong and the unit will power off automatically after you have tried for 6 times.

If you want to continue, turn your unit on and try to enter password again. The password is changeable (for more information see item “Rating”).

Vo lu me

Rotate the volume knob on the unit or press VOL+/- on the RC to increase/decrease the sound volume. The maximum level of volume is 40.

Mute

*******

1 2 3 4 5 6

7 8 9 0

V-AVM700

Press MUTE button on the unit or RC to turn the sound off. Press it again to resume.

Playing source selection

Open the “SOURCE MENU”, and then touch the option you need or select the option: FRONT, REAR, DISC, SD, USB, NAV, RADIO, BT, TV, AUX 1, AUX 2, CAMERA, OFF by moving the cursor (joystick) and then confirm.

Note: When some devices are not ready, they cannot be selected.

Open/close the monitor

Press OPEN button on the unit or OPEN/CLOSE button on the RC to open/close the monitor.

Changing the monitor tilting angle

You can adjust the monitor angle to get more convenient position. Press and hold TILT button on the unit repeatedly to change monitor angle. Also you can adjust the monitor angle by pressing TILT UP/DOWN buttons on the remote control.

Changing the display mode

Press WIDE button repeatedly the display modes will be changed as follows:

V-AVM700

If the unit cannot work correctly, you should reset the unit by pressing the RESET button on the panel with a pointed object, (such as a ballpoint pen).

Picture setup

Press and hold WIDE button the picture menu will appear. Adjust BRIGHT, CONTRAST and COLOR (in TV mode) items with cursor buttons. Press WIDE button shortly to choose between BRIGHT, CONTRAST and COLOR.

V-AVM700

Radio operations

Select radio mode

Open the “Source Menu” and select “Radio”.

Select band

Press BAND/SLOW PLAYBACK button on the RC or BAND button, or touch repeatedly the BAND icon on the screen to select bands in the following order: FM1 – FM2 – FM3 – AM1 – AM2.

Search for a station automatically

To search for a station along the increasing frequencies press RIGHT cursor button on the RC or on the unit. To search for a station along the decreasing frequencies press LEFT cursor button on the RC or on the unit. Notes: To stop searching, repeat the operation above or press other buttons having radio function. When a station is received, searching stops and the station is played. If the unit receives a stereo broadcasting, the indicator light of Stereo “ST” on the display will be lighted.

Search for a station manually

To search for a station manually, press repeatedly UP/DOWN cursor button on the RC or on the unit, or touch the numeric keypad icon and then touch the number buttons to input the radio station frequency numbers. During manually searching, the frequency will be changed in steps.

Presetting stations automatically

Press ENTER cursor button on the RC or on the unit, or press AS button on the panel/touch the AS button on the screen. Only stations with sufficient signal strength will be detected and stored in the memory. Notes: To stop automatic presetting, press buttons having radio functions. After automatic presetting, the previous stations frequency will be overwritten. The unit has 5 bands, such as FM1, FM2, FM3, AM1, AM2, and each band can store 6 stations; hence the unit can store 30 stations in all.

V-AVM700

Presetting stations manually

Method 1: Press the number buttons on the RC. Method 2: Press the MEM button on the screen to open the station preset menu. Then press one of the 6 buttons of the menu. The menu will be closed automatically. If you want to exit, press EXIT button. Notes: After manual presetting, the previous stations frequency will be overwritten. Number buttons 1 to 6 corresponds to station P1 to P6. For each band, P1 to P6 can store 1 station.

Recall the preset stations

Press the corresponding number button on the RC or touch an onscreen preset button to select the corresponding stored station.

Preview scan

Open the second window by pressing 1/2 button. Press SCN button on the RC or touch the PS button on the screen. Preview scan searching is such a process that the searching pauses when a station is received and then played for 10 seconds. After being played, the unit continues the process until the whole band is detected.

Note: To stop preview scan, repeat the operation above again.

Local radio station searching

Press the LOC button on the screen to open pr close LOCAL function. DX (distance) seeking mode is contrary to LOC mode. You can receive more stations with this seeking mode. When LOCAL seeking is on, only radio stations with strong radio signal could be received. Notes: When the local radio station searching is on, the indicator light “LOC” lights up; whereas the light goes off. The unit will switch to distant seeking mode after LOCAL seeking is closed.

V-AVM700

RDS operations

AF function

Alternative Frequencies Lists are used for the same program service and used in conjunction with the PI code (Program Identification code) to assist automatic tuning. Using this information, a radio can automatically search out another station that is playing the same material. This is useful when the station you are listening to is fading out. To activate AF function press AF button on the screen. To cancel the function, press the button repeatedly. Note: During auto switching radio frequency, some interference could be heard. Turning off AF function can settle this problem.

TA function

The ТА (Traffic Announcement flag) function lets the unit receive traffic announcements automatically no matter what media source is playing back. The ТА function can be activated for a TP (Traffic Program) station broadcasting traffic information. To activate TA function, press TA button on the screen. To cancel the function, press the button repeatedly. Note: Receiving traffic announcements under other modes When ТА is activated and a traffic announcement is

RDS is available only in FM bands. The unit provides basic functions of RDS, including PI (Program Identification), radio station name, RT (Radio Text), CT (Clock Time), AF (Alternative Frequency), ТА (Traffic Announcement) and PTY (Program Type) Selection.

V-AVM700

received, the current playing source will be overridden by the traffic announcement if the current radio band is FM and the “ТА” indicator lights up, indicating that the unit is waiting for traffic announcements. The unit returns to the original source after the traffic announcement has been received.

PTY function

PTY is the abbreviation for Program Type which is a code defining the type of program being broadcast (e.g. News or Rock).

Program service (PS)

Used for receiver displays of an 8 character alpha numeric Program Service name which may use Upper or Lower case characters, e.g. {BBC_4_FM}, {Classic_}. The function is for indicating and cannot be operated.

CT (Clock time)

Some stations broadcast the time and date within the encoded RDS signal. The clock time is automatically adjusted when “CT” is set to “On”.

RT (Radio Text)

When this function is activated, the unit will display short message data transmitted from the provider, such as station information, the name of the current broadcasting song and the artist name. The function is for indicating and cannot be operated.

TP (Traffic Program Flag)

A flag indicating whether the station broadcasts traffic announcements at some time in the day. The function is for indicating and cannot be operated.

V-AVM700

DISC operations

Insert a disc

Upon inserting a disc, the unit will change to disc mode automatically. Notes: Please confirm whether there is a disc in the unit before you insert another one. The unit will exit current playing source and enter DVD mode when a disc is inserted. Some recorded discs, such as CD-R, CD-RW, DVDR, DVD+R, DVD-RW, DVD+RW cannot be played back because of different recording status. Otherwise, the discs without being closed could not be played back.

Eject the disc

Press EJECT button on the RC or on the unit. Notes: After ejecting the disc, the unit reverts to SD card mode automatically if you have inserted SD card, or the unit reverts to radio mode. You can eject a disc with the unit powered off. The unit remains off after the disc is ejected.

Using the touch screen controls

The touch key areas for DVD playback are outlined below:

A – Open “Source Menu” B – Display onscreen control menu

V-AVM700

Onscreen control buttons

Disc type

MP3/WMA CD VCD DVD MPEG Pictures

Icon

Numeric

keypad

Numeric

keypad

Numeric

keypad

Numeric

keypad

Numeric

keypad

Numeric

keypad

Setup menu Setup menu Setup menu Setup menu Setup menu Setup menu

- Fast forward Fast forward Fast forward Fast forward -

- Fast rewind Fast rewind Fast rewind Fast rewind -

Previous Previous Previous Previous Previous Previous

Next Next Next Next Next Next

Play/Pause Play/Pause Play/Pause Play/Pause Play/Pause Play/Pause

Stop Stop Stop Stop Stop Stop

- -

A second

Repeat Repeat Repeat Repeat Repeat Repeat

A second

V-AVM700

PBC

A – B

All

Random Random Random - Random -

- - - - -

- - Zoom out - - Zoom out

- - Zoom in - - Zoom in

Music files - - - Music files Music files

Picture files - - - Picture files Picture files

Video files - - - Video files Video files

EQ setup EQ setup EQ setup EQ setup EQ setup EQ setup

- - PBC - - -

- - A-B repeat A-B repeat - -

All files - - - All files All files

Rotate

clockwise

Rotate

anticlockwise

Back

- - Exit menu Exit menu Exit menu Exit menu

V-AVM700

AUDIO

SUBTITLE

DISP

- -

- - -

- -

Channel

switching

Display

information

Dialogue

language

Subtitle

language

Display

information

Dialogue

language

Subtitle

language

Display

information

Display

information

TITLE

REAR

PIP

DIR+

DIR-

SLIDE

- - DVD MENU - -

- - - DVD TITLE - -

Rear zone Rear zone Rear zone Rear zone Rear zone Rear zone

PIP source PIP source PIP source PIP source PIP source PIP source

Next folder - - - - Next folder

folder

- - - - -

- - - -

folder

Picture slide

modes

Reverse

horizontally

Reverse

vertically

Select the

V-AVM700

- - - - -

Select the

Stop playback temporarily

To stop playback temporarily, press ENTER cursor button on the RC or on the unit. To resume normal play, repeat the operation.

Stop playback entirely

Press STOP button on the RC.

• For DVD/VCD discs: do the above operation for the first time, playback is paused and the break point is stored. When you start playback again, playback starts from where it has been stopped (resume play). Do the above operation twice, playback is canceled. When you start playback again, for DVD, playback starts from the beginning of the last title; for VCD, playback starts from the beginning of the disc.

• For other discs: do the above operation, playback is canceled. When you start playback again, playback starts from the beginning of the file.

Display file list

There are two methods to display file list when the picture or video file of one disc contained MP3, WMA, JPEG, MPEG files is played back:

1. Using the remote control. Press the STOP button on the RC.

2. Using the touch screen. Open onscreen control buttons and press the STOP button.

Fast forward/Fast reverse

When a DVD, VCD or CD disc is played back, press DOWN cursor button on the RC or on the unit repeatedly. Notes: When a music CD disc is played back, the audio output remains open if the fast forward playback is applied. When an MP3 or JPEG disc is played back, this function is prohibited.

V-AVM700

Slow forward/Slow reverse

When a DVD, VCD or CD disc is played back, repeatedly press BAND/SLOW PLAYBACK button on the RC or BAND button on the unit to activate slow playback function.

Play a next or previous file

To go to next/previous file, press RIGHT/LEFT cursor button on the RC or on the unit.

Repeat playback

Press repeatedly RPT button on the panel or on the RC.

Disc type Repeat mode

DVD Repeat chapter – Repeat title – Repeat off

VCD (PBC off) Repeat one – Repeat all – Repeat off

CD Repeat one – Repeat all – Repeat off

MP3/WMA Repeat one – Repeat folder – Repeat all – Repeat off

MPEG Repeat one – Repeat folder – Repeat all – Repeat off Picture Repeat one – Repeat folder – Repeat all – Repeat off

Note: When a VCD is played back, this function is prohibited if the PBC is on. Turning off the power or switching playing source to other modes and back will cancel this function.

Repeat A-B

Press the RPT/A-B button on the RC repeatedly. When a DVD, VCD or CD disc is played back, you can play back the contents between the time points from A to В repeatedly. Set A=> Repeat On => Canceled

V-AVM700

Random playback

Press the RDM button on the RC repeatedly. When this function is on, the contents in the disc will be played back randomly.

Intro playback

Press SCN button on the RC. When this function is on, the unit will play back the first 10 seconds of each track of a VCD or CD disc. You can search the file you desired using this function. To cancel this function, repeat the operation above.

Search for a particular file

When a DVD, VCD or CD disc is played back, you can search for a particular chapter/track by pressing the number buttons on the RC. For example, if you want to select the 15th track, you should press number buttons [1], [5] and then confirm by pressing ENTER button.

GOTO search

Enter the GOTO search and select search mode by pressing GOTO button repeatedly.

• For DVD: using the onscreen number buttons select either title, or chapter or time for search.

• For VCD (PBC is off) and MPEG files: using the onscreen buttons select either track or time for search.

• For CD, MP3 and picture file: using the onscreen number buttons select the file for search.

Press GOTO button once more to exit the GOTO search mode.

Using DVD menu/title

This function is only available for the DVD discs having “Menu/Title”.

1. Enter the DVD Menu/Title by pressing MENU or TITLE buttons. You can select the languages, subtitles and etc.

+ 90 hidden pages

Varta V-AVM700 User Manual [ru]

Specifications and Main Features

Frequently Asked Questions

User Manual