Varad PLX318 User Manual
Installation Guide
PLX312
PLX318
Thank you for purchasing Illuminaire’s home theater lighting system.
You can use this guide to:
• Get familiar with your home theater lighting system.
• Installation.
•Operation.
1
Clamps/Tape/Tie straps Power supply
2
Contents
LED light bars
Digital Controller
Remote control
Lithium battery
Remote Control LED
Diagram
3
Remote control LED port
4 LED light bar ports
Installation
Back view of television
Power supply port
Diagram 1
1“-2”
• The LED light bars should be installed 1”-2” from the edge
of the television and centered vertically (diagram 1). Use the
supplied tape, clamps and tie straps (diagram 2) for mounting.
• The Digital controller can be mounted to the rear of the
television or placed in any other suitable location.
• The remote control LED can be installed in any location
where it will be visible by the remote control transmitter.
• Plug the LED light bars into any of the 4 ports on the digital controller.
• Connect the power supply to the digital controller.
• Connect the remote control LED to the digital controller.
All excess cable should be bundled together for a clean appearance.
Proceed to section 4 for operation
Diagram 2
4
Power - to turn system on and o.
Color - Press left or right arrow to select desired color. Push and hold for rapid change.
Operation
! Install lithium battery for the remote control.
Color show
Smooth - Automatically cycles through millions of colors in approximately 30 mins.
Push to start/stop
Breath - Slow fade in and out of selected color. Push to start/stop
1 thru 7 Color show
Step - Steps through your 7 favorite colors. Push to start/stop
Smooth - Gradually cycles through your 7 favorite colors with a smooth
transition. Push to start/stop
Sleep - Turns system o in increments of 30 minutes. Push once for 30 minutes, push twice
for 1 hour etc.... up to a maximum of 6 hours. The system will conrm settings with
a quick ash for each 30 min increment.
Night - Turns system into a night light. Push momentarily to cycle through the dierent
brightness levels.
Favorite colors - system can memorize 7 of your favorite colors.
Programming your favorite colors.
Step 1: Select a system color using the left or right color arrows.
Step 2: Press “mem” button once. System will ash once to conrm.
Press buttons 1 thru 7 to memorize color.
5
For those installations requiring a discrete power o command:
Press and hold “5” then press “7” to force o.
To reset back to factory defaults:
Press and hold “5” then press “mem”.
6
1. You can adjust the width of the light behind the television by rotating the LED light
bars. Rotating the LEDs outward will broaden the light dispersion while rotating the
LEDs inward will reduce the dispersion.
2. Studies have shown that a light color of 6500K (pure white) will signicantly reduce
eye strain while watching TV in low ambient light conditions.
3. Optional expansion LED light bars are available if you want to light up other areas such as
speakers, book cases, coves etc...
Advanced Control Features
The Home Theater Experience Tips
7
8
Technical Support
Please E-mail any technical questions you may have to - techsupport@illuminaire.com
or visit our website at - www.illuminaire.com
Warranty
Illuminaire’s product warranty covers against breakage due to defects in
materials or workmanship for one year from the date of purchase. Warranty is
only valid with proof of purchase from an Authorized illuminaire Dealer.
Illuminaire’s warranty program does not cover cosmetic damage, and damage
due to acts of God, accident, misuse, abuse or negligence to the product. Repair
or replacement as provided under this warranty is the exclusive remedy of the
consumer. Illuminaire shall not be liable for any incidental or consequential
damage for breach of any express or implied warranty on this product. Except
to the extent provided by this warranty or prohibited by applicable law, there
are no implied nor expressed warranties or merchantability or tness for a
particular purpose of this product.
Loading...