SATA 150 PCI RAID Card
2-Channel
User Manual
Ver. 3.00
All brand names and trademarks are properties of their
Respective owners.
Features
z Silicon Image SiI3512 SATA controller chip
z Compliant with PCI Specification, Rev. 2.3
z Compliant with Serial ATA 1.0 specification
z Provides two independent channels to support up to two Serial
ATA drives
z Supports RAID0(striping) and RAID1(mirroring) for speed and
data protection respectively
z HDDs function normally when not in RAID sets
z Supports SATA up to 150MB/Sec
z Supports Windows® 2000, XP/2003 32/64 bit, Vista 32/64 bit
Connectors
z 2 x internal SATA connectors
z 2 x external eSATA connectors
System Requirements
z Pentium-class computer with one available PCI slot
z Windows® 2000, XP/2003 32/64 bit, Vista 32/64 bit
MN2000000107 Page2
Package Contents
z 1 x SATA 150 PCI RAID Card 2-Channel
z 1 x Driver CD
z 1 x User’s Manual
Optional Accessories
z SATA Data Cable
z SATA Power Cable
Hardware Description
Note: There are four SATA ports in SATA 150 PCI RAID Card
2-Channel. We name these ports from A to D. Ports A & B are internal
SATA ports. Ports C & D are external SATA ports. Changing the
jumper setting allows you to select between external and internal ports
to use. By default, Port A and B are working.
MN2000000107 Page3
E (Jumper Settings)
JP Description Active Port
J1-J4 1-2 close Enable SATA Port C
2-3 close Enable SATA Port A
J5-J8 1-2 close Enable SATA Port D
2-3 close Enable SATA Port B
MN2000000107 Page4
Hardware Installation
1. Turn Off the power to your computer and any other connected
peripheral devices.
2. Unplug the power cord form the back of the computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card’s bus connector with
the selected PCI slot on the motherboard. Push the board down
firmly, but gently, until it is well seated.
6. Replace the slot bracket’s holding screw to secure the card.
Device Connection
The SATA 150 PCI RAID Card is a two channel Serial ATA controller
that supports up to two Serial ATA hard disk drives. It is recommended
to use identical hard drives for all RAID configurations.
1. Install your hard disk drive(s) in chassis.
2. Connect the Serial ATA hard disk drive to the system power
supply using the included Serial ATA power cable.
3. Connect one end of the Serial ATA cable to the hard disk drive.
4. Attach the other end of the Serial ATA cable to the Serial ATA port
MN2000000107 Page5
on the SATA 150 PCI Raid Card 2-Channel
5. Follow the same instructions to connect up to two hard drives.
Device connection is now complete.
6. Replace the computer cover and reconnect the power cord.
RAID Arrays
RAID Arrays are setup in the SATA 150 PCI RAID Card 2-Channel’s
BIOS.
RAID 0 (Striping)
This RAID array to be used on New/Blank hard drives. Striping will
destroy existing data on the hard drive. Auto Configuration is
recommended. For applications that require custom chunk size,
Manual Configuration is offered.
Auto configuration (recommended)
The default chunk size is 64k when selecting Auto configuration.
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
MN2000000107 Page6
3. Select Striped, then press Enter.
4. Select Auto configuration, then press Enter.
5. When asked Are You Sure (Y/N)?, press Y to accept.
6. Press Ctrl+E to exit the BIOS.
7. When asked Are you sure to exit (Y/N)?, press Y to exit and
reboot.
8. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
Manual configuration
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
3. Select Striped, then press Enter.
4. Select Manual configuration then press Enter
5. Select the first drive, press Enter.
6. Select the second drive, press Enter.
7. Select chunk size from 4k, 8k, 16k, 32k, 64k or 128k, then press
Enter.
8. When asked Are You Sure(Y/N)?, press Y to accept.
MN2000000107 Page7
9. Press Ctrl+E to exit the BIOS.
10. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot.
11. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
RAID 1 (Mirror)
For New/Blank Hard Drives
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
3. At the next screen select Mirrored then press Enter.
4. Select Auto configuration, then press Enter.
5. When asked Are You Sure(Y/N)?, press Y to accept.
6. Press Ctrl+E to exit the BIOS.
7. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot.
8. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
MN2000000107 Page8
For Existing Hard Drives with Data
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter.
3. At the next screen select Mirrored then press Enter.
4. Select Manual configuration, then press Enter.
5. Select the Source drive, press Enter.
6. Select the Targ et drive, press Enter.
7. Enable Disk Copy, select Ye s , then press Enter.
Note: Enable Disk Copy – Copy current content of source driver to
mirror drive; Disable Disk Copy – RAID 1 set formed must be
repartitioned and reformatted to guarantee the consistency in their
contents.
8. Press Ctrl+E to exit the BIOS.
9. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot.
Note: If during boot the RAID BIOS reports an RAID1 set is in
Rebuild status, The rebuild will continue after boot sequence is
complete, disregard the message, continue booting, and let the Mirror
rebuild.
MN2000000107 Page9
Rebuilding a Failed Mirror Set
When a failure to one member occurs, you will be notified either by the
RAID BIOS during boot or by the SATARAID GUI while in
Windows. The steps below will guide you in rebuilding a failed mirror
set.
1. Replace the failed drive with one of equal or greater capacity, then
start the computer.
2. During boot press Ctrl+S or F4 to enter the RAID BIOS.
3. Select Rebuild Mirrored Set then press Enter.
4. Select the desired set and then press Enter.
5. When asked Are You Sure(Y/N)?, press Y to confirm.
6. The set will be rebuilt.
Deleting RAID Arrays
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter
the RAID BIOS.
2. Select Delete RAID Set, then press Enter.
3. Select the RAID set then press Enter.
4. When asked Are You Sure(Y/N)?, press Y to confirm.
MN2000000107 Page10
Resolving Conflicts
When a RAID set is created, then metadata written to the disk includes
drive connection information. If, after a disk failure, the replacement
disk was previously part of a RAID set (or used in another system), it
may have conflicting metadata. If so, this will prohibit the RAID set
from being either created or rebuilt, in order for the RAID set to
function properly, this old metadata must be first overwritten with the
new metadata. To resolve this, from the main BIOS window select
Resolve Conflicts, then press Enter, the correct metadata, including
the correct drive connection information, will be written to the
replacement disk.
Low Level Format
Low Level Format is build into the RAID BIOS to make it more
convenient to erase the entire contents of a hard disk drive, including
data, drive and partition information. The Low Level Format utility
works on single hard drive only, before the RAID set is configured.
BIOS Configuration
The Serial ATA 2-Channel RAID adapter BIOS will appear every time
MN2000000107 Page11
your system starts up. If the BIOS doesn’t show, please try your
controller in another PCI slot. During this (POST) process, the BIOS
will show up and indicate the devices attached to it.
Driver Installation
For Windows® 2000
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “
PCI_IO\Sata\RAID” folder, found on the driver CD, onto a
blank floppy disk then follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Windows® 2000 installation procedure.
3. At the Windows® 2000 Setup screen, press F6 to install the RAID
driver.
4. When prompted, press S to specify the location of the driver.
5. Insert the floppy disk, then press Enter.
6. Select Silicon Image SiI 3x12 SATARAID Controller for
Windows NT 4.0 and 2000, then press Enter.
7. Press Enter again to finish driver installation, then follow the
MN2000000107 Page12
on-screen instructions to complete the Windows installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
Windows.
2. At Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device(recommend)
then click Next.
4. Insert the driver CD, check CD-ROM drives, uncheck the other
boxes, click Next, then click Next again.
5. If the Digital Signature Not Found message appears, click Yes .
Our driver has been thoroughly tested for stability and
compatibility.
6. Click Finish.
For Windows® XP/Server 2003
For New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “
PCI_IO\Sata\RAID” folder, found on the driver CD, onto a
MN2000000107 Page13
blank floppy disk then follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press F6 to install the RAID driver.
4. When prompted, press S to specify the location of the driver.
5. Insert the floppy disk, then press Enter.
6. Select Silicon Image SiI 3x12 SATARaid Controller for
Windows XP/Server 2003, then press Enter.
7. Press Enter to finish driver installation, then follow the on-screen
instructions to complete the Windows installation.
Note: If the Security Alert warning pops up, click Ye s . Our driver has
passed Microsoft compatibility testing, this message appears during
new installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
Windows.
2. At the Found New Hardware Wizard:
XP(w/SP1 or earlier)/Server 2003: continue to step #3
XP(w/SP2 or later)/Server 2003(w/SP1 or later): select No, not
MN2000000107 Page14
this time, then click Next.
3. Insert the driver CD, select Install the software automatically
(Recommended), and click Next.
4. Click Finish.
For Windows®XP-x64/Server 2003-x64
For New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “
PCI_IO\Sata\64-bit Windows RAID Driver” folder, found on the
driver CD, onto a blank floppy disk then follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press F6 to install the RAID driver.
4. When prompted, press S to specify the location of the driver.
5. Inset the floppy disk, then press Enter.
6. Select Silicon Image SiI 3x12 SATARaid Controller (64-bit
Extended) or Silicon Image SiI 3x12 SATARaid Controller
(Itanium), then press Enter.
7. Press Enter to finish driver installation, then follow the on-screen
MN2000000107 Page15
instructions to complete the Windows installation.
Note: If the Security Alert warning pops up, click Ye s . Our driver has
passed Microsoft compatibility testing, this message appears during
new installation.
For An Existing Installation
1. At the Found New Hardware Wizard, select No, not this time,
then click Next.
2. Insert the driver CD, select Install the software automatically
(Recommended), and click Next.
3. Click Finish.
For Windows® Vista
For New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “
PCI_IO\Sata\RAID” folder, found on the driver CD, onto a
blank floppy disk then follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
MN2000000107 Page16
3. At the Windows Setup screen, press Load Driver to install the
RAID driver.
4. Insert the floppy disk, please select Silicon Image SiI 3512
SATARaid Controller (A:\si3112r.inf), then press Next. (Change
A:\ to match your floppy drive letter)
5. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
Windows.
2. At Found New Hardware Wizard, select Locate and install
driver software (recommended).
3. Please insert the CD driver bound with SATA 150 PCI RAID card
into your CD-ROM Drive, click Next.
4. If the system prompts the user informing the drivers are not
signed, select the option Install this driver software anyway.
5. Click Close to complete the installation.
MN2000000107 Page17
For Windows® Vista-x64
For New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “
PCI_IO\Sata\64-bit Windows RAID Driver” folder, found on the
driver CD, onto a blank floppy disk then follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press Load Driver to install the
RAID driver.
4. Insert the floppy disk, please select Silicon Image SiI 3512
SATARaid Controller (A:\si3112r.inf), then press Next. (Change
A:\ to match your floppy drive letter)
5. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up to
Windows.
2. At Found New Hardware Wizard, select Locate and install
MN2000000107 Page18
driver software (recommended).
3. Please insert the CD driver bound with SATA 150 PCI RAID card
into your CD-ROM Drive, click Next.
4. If the system prompts the user informing the drivers are not
signed, select the option Install this driver software anyway.
5. Click Close to complete the installation.
To Verify Driver Installation
1. Right click My Computer and click Manage.
2. Select Device Manager.
3. Look for the following:
Windows® 2000/XP/2003: Double click SCSI and RAID
Controller:
-Silicon Image SiI 3512 SATARaid Controller should be
displayed
Windows® Vista:
-Silicon Image SiI 3512 SATARaid Controller should be
displayed
Double click Storage controllers:
MN2000000107 Page19
JAVA 2 Runtime Environment Installation
The Java 2 Runtime Environment is required for the SATARAID
Management Software.
1. Please insert the CD driver bound with SATA 150 PCI RAID card
into your CD-ROM Drive.
2. At the Windows desktop click Start, then Run.
3. Type D:\PCI_IO\Sata\Medley\InstallSATARaid.exe, then click
OK. (Change D: to match your CD-ROM drive letter)
4. Follow the on-screen instructions to complete the installation.
SATARAID Management Software Installation
1. Please insert the CD driver bound with SATA 150 PCI RAID card
into your CD-ROM Drive.
2. At the Windows desktop click Start, then Run.
3. Type
D:\PCI_IO\Sata\Medley\jre-1_5_0_05-windows-i586-p.exe,
then click OK. (Change D: to match your CD-ROM drive letter)
4. Follow the on-screen instructions to complete the installation.
Loading...