Vanguard Heating VMH26PRA User Manual

Download

VENT-FREE PROPANE/LP GAS

COMPACT CLASSIC HEARTH® FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

VMH26PRA

15,000 to 26,000 Btu/Hr

Remote Control Ready

Shown with Optional

Cabinet Mantel/Hearth

Base Accessory

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed

by a qualified installer, service agency, or the gas supplier.

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to

Ventilation

this manual.

Air for Combustion and

section on page 5 of

This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

SAFETY INFORMATION

WARNINGS

WARNING ICON G 001

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this fireplace. Improper use of this fireplace can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the fireplace may not be working properly. Get fresh air at once! Have fireplace serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.

Propane/LP Gas: Propane/LP gas is odor-

less. An odor-making agent is added to propane/LP gas. The odor helps you detect a propane/LP gas leak. However, the odor added to propane/LP gas can fade. Propane/LP gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this fireplace.

WARNING: Any change to this fireplace or its controls can be dangerous.

WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.

WARNING: Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this fireplace.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.

Fireplace front and screen becomes very hot when running fireplace. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young children when they are in same room with fireplace.

You must operate this fireplace with the fireplace screen in place. Make sure fireplace screen is in place before running fireplace.

Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) inside any structure. Locate propane/ LP supply tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier

from a neighbor’s phone. Follow the gas supplier’s instructions

• if you cannot reach your gas supplier,

call the fire department

4. This fireplace shall not be installed in a bedroom or bathroom.

5. Do not use this fireplace as a woodburning fireplace. Use only the logs provided with the fireplace.

6. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of fireplace.

7. This fireplace is designed to be smokeless. If logs ever appear to smoke, turn off fireplace and call a qualified service person. slight smoking could occur due to log curing and fireplace burning manufacturing residues.

8. T o prevent the creation of soot, follow the instructions in Cleaning and main- tenance, page 21.

9. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

10. This fireplace needs fresh air ventilation to run properly . This fireplace has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the fireplace if not enough fresh air is available. See Air for Combus- tion and Ventilation, pages 5 through

7. If fireplace keeps shutting off, see Troubleshooting , pages 22 through 24.

11. Do not run fireplace

• where flammable liquids or vapors

• under dusty conditions.

12. Do not use this fireplace to cook food or burn paper or other objects.

13. Never place any objects in the fireplace or on logs.

14. Do not use fireplace if any part has been under water. Immediately call a qualified service technician to inspect the room fireplace and to replace any part of the control system and any gas control which has been under water.

15. Turn off and unplug fireplace and let cool before servicing. Only a qualified service person should service and repair fireplace.

Note:

During initial operation,

are used or stored.

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

SAFETY INFORMATION

Continued

16. Operating fireplace above elevations of 4,500 feet could cause pilot outage.

17. Do not operate fireplace if any log is broken. Do not operate fireplace if a log is chipped (dime-sized or larger).

18. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

LOCAL CODES

Install and use fireplace with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code ANS Z223.1, also known as NFPA 54*.

*Available from: American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room fireplaces. The ODS/ pilot shuts off the fireplace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This system requires no matches, batteries, or other sources to light fireplace..

REMOTE CONTROL ACCESSORIES

There are four optional remote controls that can be purchased separately for this log heater:

• hand-held ON/OFF remote

• hand-held thermostat remote

• wall mounted thermostat

• wall mounted ON/OFF switch See Accessories, pages 28 and 29.

UNPACKING

1. Remove log box and fireplace from carton. hood is inside the cardboard protective end wrap on the left side of fireplace (as viewed from front). A decal is on the outside of the cardboard end wrap stating hood is enclosed (see Figure 2).

2. Remove hood from cardboard protective end wrap as shown in Figure 2.

3. Remove all protective packaging applied to fireplace for shipment.

4. Make sure your fireplace includes one hardware packet.

5. Check fireplace for any shipping damage. If fireplace is damaged, promptly inform dealer where you bought fireplace.

Hood Enclosed Decal

IMPORTANT:

THIS PACKAGE CONTAINS A FIREPLACE HOOD. UNWRAP

CARTON AND REMOVE HOOD

BEFORE DISCARDING

PROTECTIVE PACKAGING.

The fireplace

Cardboard Protective Fireplace End Wrap

PRODUCT IDENTIFICATION

ARM

N O

M E R

Control Knob

Selector Switch (Optional)

Ignitor Button

Figure 1 - Vent-Free Natural Gas Compact Fireplace

COOLER

TEM

AUTO O N

O FF

Fireplace Cabinet

Screen

Log Set

Remote Control (Optional)

Hood

Figure 2 - Removing Fireplace Hood

107034

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

ASSEMBLY

WARNING: Always have branch support and screen in place before operating fireplace. This prevents excessive temperatures on fireplace surfaces.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this fireplace may result in property damage or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

• Phillips screwdriver

• 5/16" hex wrench

• slotted screwdriver

• scissors

Installing Log

1. Lift screen up and pull out to remove.

2. Cut two plastic straps to remove the log from the firebox cavity.

3. An optional blower is available. See Ac- cessories, pages 28 and 29. Install optional blower now. Follow installation instructions provided with blower.

4. Remove log packaging material and discard packaging. Gently place log set on burner support (see Figure 3). The log should fit flat against top of burner support and log locators fit into the slots under the log. Do not allow log to contact flame. If flame contacts log, soot will be created.

5. Reattach screen by placing the notches in the screen frame over the shoulder screws and pushing down.

Log

Screen

Figure 3 - Assembling Fireplace

Assembling Hood

1. Locate four black phillips sheet metal screws from the hardware packet.

2. Rotate hood as shown in Figure 4. Make sure hood tabs point toward fireplace.

3. Insert hood tabs between baffle and louvers (see Figure 4).

Hood Tabs

Shoulder Screw

Burner Support

Branch Support

4. Gently rotate hood to upright position. Make sure hood tabs are behind louvers and hood is resting on firebox top (see Figure 4).

5. Align screw holes on hood with screw holes on firebox top.

6. Insert screws as shown in Figure 4. Tighten screws firmly.

Louver

Hood

Hood Tab

Baffle

Figure 4 - Assembling Hood

For more information, visit www.desatech.com

Sheet Metal Screws

Firebox Top

107034

OWNER’S MANUAL

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.

Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuelburning appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code, NFPA 54/ANS Z223.1, Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space The information on pages 5 through 7 will

help you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10 per pa-sec-m2) or less with openings gasketed or sealed

b. weather stripping has been

added on openable windows and doors

c. caulking or sealants are applied

to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air. See

From Outdoors

If your home does not meet all of the three criteria above, proceed to

and

Ventilation Air

, page 7.

mining Fresh-Air Flow For Fireplace Location,

page 6.

and

Deter-

-11

Confined and Unconfined Space

The National Fuel Gas Code, ANS Z223.1

defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air.

* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

107034

Continued

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

AIR FOR COMBUSTION AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space. Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height). Length x Width x Height = _________________cu. ft. (volume of space)

Example:

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)

Example:

3. Add the Btu/Hr of all fuel burning appliances in the space. Vent-free fireplace ___________________ Btu/Hr Gas water heater* ___________________ Btu/Hr Gas furnace ___________________ Btu/Hr Vented gas heater ___________________ Btu/Hr Gas fireplace logs ___________________ Btu/Hr Other gas appliances* + ___________________ Btu/Hr Total = ___________________ Btu/Hr * Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

________________________ Btu/Hr (maximum the space can support) ________________________ Btu/Hr (actual amount of Btu/Hr used)

Example:

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 7.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 7. C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

Example:

Gas water heater 30,000 Btu/Hr Vent-free fireplace + 26,000 Btu/Hr Total = 56,000 Btu/Hr

51,200 Btu/Hr (maximum the space can support) 56,000 Btu/Hr (actual amount of Btu/Hr used)

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the

For more information, visit www.desatech.com

National Fuel Gas Code, ANS Z223.1, Section 5.3

or applicable local codes.

107034

AIR FOR COMBUSTION AND

OWNER’S MANUAL

VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 5). You can also remove door into adjoining room (see option 3, Figure 5). Follow the National Fuel

Gas Code, NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

WARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

12"

Ventilation Grills

Ventilation

Grills

into Adjoining

Room,

Option 1

Figure 5 - Ventilation Air from Inside Building Shown with Optional Mantel

Remove Door into Adjoining

Room,

Option 3

Outlet Air

Into Adjoining Room,

12"

Option 2

Ventilated Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, NFPA 54/ANS Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of ventilation

grills or ducts.

IMPORTANT:

inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent.

107034

Do not provide openings for

Outlet Air

To Attic

Crawl

Space Inlet Air

Inlet Air

Figure 6 - Ventilation Air from Outdoors Shown with Optional Mantel

For more information, visit www.desatech.com

Ventilated

Crawl Space

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

Note:

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified service person must install fireplace. Follow all local codes.

WARNING: Never install the fireplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable objects are less than 36 inches from the front, top, or sides of the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: This fireplace creates warm air currents. These currents move heat to wall surfaces next to fireplace. Installing fireplace next to vinyl or cloth wall coverings or operating fireplace where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.

IMPORTANT:

ture to the air. Although this is beneficial, installing fireplace in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion

and Ventilation, pages 5 through 7.

Vent-free fireplaces add mois-

Your Vanguard fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fireplace Installation, page 9).

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply is not propane/LP, do not install fireplace. Call dealer where you bought fireplace for proper type fireplace.

INSTALLATION ITEMS

Before installing fireplace, make sure you have the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection*

• ground joint union

• sediment trap

• tee joint

• pipe wrench * An CSA/AGA design-certified equipment

shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA/AGA designcertified equipment shutoff valve from your dealer. See Accessories, pages 28 and 29.

Note:

If desired, purchase a four-sided brass trim kit for built-in installations. See Acces- sories, pages 28 and 29.

LOCATING FIREPLACE

WARNING: Maintain the mini-

mum clearances shown in Figure 7. If you can, provide greater clearances from floor, ceiling, and joining wall.

You can recess firebox into the wall. You can also position fireplace in the optional cabinet or corner mantels. Only use optional cabinet or corner mantels specified in this manual. Purchase the optional mantel from your dealer (see Acces- sories, pages 28 and 29).

IMPORTANT:

CAUTION: If you install the

fireplace in a home garage

• fireplace pilot and burner must be at least 18 inches above floor.

• locate fireplace where moving vehicle will not hit it.

For convenience and efficiency, install fireplace

• where there is easy access for operation, inspection, and service.

• in coldest part of room.

An optional blower kit is available from your dealer (see Accessories, pages 28 and

29). If planning to use blower, locate fire-

place near an electrical outlet.

Minimum Clearances For Side Combustible Material, Side Wall, and Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall should follow diagram in Figure 7.

Example:

shelf, etc. is made of combustible material and protrudes 3 1/2" from the wall. This combustible material must be 4" from the side of the fireplace opening (see Figure 7).

B. Clearances from the top of the fireplace

opening to the ceiling should not be less than 42 inches.

C. For mantel clearances, see Figure 11

on page 10.

FIREBOX

*Minimum 16 inches from Side Wall

Figure 7 - Minimum Clearance for Combustible to Wall

The face of a mantel, book-

Example

.5 2

1 4 6 8 10 12 14 16

INCHES

121/ 101/

8 7 51/ 31/ 1 7/8 7/16

INCHES

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

INSTALLATION

Continued

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. An optional brass trim kit accessory is available (see Accessories, pages 28 and 29). Brass trim will extend past sides of fireplace approximately 1/2 inch. This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace, but you must follow the clearances shown in Figure 11, page 10. Follow the instructions below to install the fireplace in this manner.

Actual Framing Height 26" 26 7/8" Front Width 26 3/4" 26 7/8" Depth 9 1/2" 10 1/2" Bottom 3/4" 3/4"

1. Frame in rough opening. Use dimensions shown in Figure 8 for the rough opening.

If installing in a corner, use dimensions shown in Figure 9 for the rough opening. The height is 26 7/8" which is the same as the wall opening above.

10 1/2"

26 7/8"

3/4" Off

26 7/8"

Figure 8 - Rough Opening for Installing in Wall

36 5/8"

26 7/8"

51 3/4"

The Floor Minimum

25 7/8"

2. If installing GA3400T blower accessory, do so at this time. Follow instructions included with blower accessory.

Note:

If not installing blower accessory, you may wish to run electrical wiring to your fireplace for future blower installation (see Accessories, page 28 and 29). Use only approved three-wire electrical wiring.

WARNING: If pre-wiring, do not connect wiring to any electrical source at this time.

Install fireplace electrical outlet and connect wiring to outlet before connecting to electrical source. The fireplace electrical outlet is included with the GA3400T blower accessory.

Only use the fireplace electrical outlet supplied with the GA3400T blower accessory.

Note:

A qualified installer should make

all electrical connections.

3. Install gas piping to fireplace location. This installation includes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping.

4. If you have not assembled firebox, follow instructions on page 4.

5. Carefully set fireplace in front of rough opening with back of fireplace inside wall opening.

6. Attach flexible gas line to fireplace gas regulator. See Connecting Fir eplace to Gas Supply, page 14.

7. Bend four nailing flanges on outer casing with pliers (see Figure 10).

8. Attach fireplace to wall studs using nails or wood screws through holes in nailing flange.

9. Check all gas connections for leaks. See Checking Gas Connections, page 15.

10. If using optional brass trim kit, install the trim after final finishing and/or painting of wall. See instructions included with brass trim accessory for attaching brass trim.

IMPORTANT:

When finishing your firebox, combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top edge of the firebox. Combustible materials should never overlap the firebox front facing.

WARNING: Do not allow any combustible materials to overlap the firebox front facing.

IMPORTANT:

Noncombustible materials such as brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.

WARNING: Do not allow noncombustible materials to cover any necessary openings like louvered slots.

WARNING: Never modify or cover the louvered slots on the front of the firebox.

WARNING: Use only noncombustible mortar or adhesives when overlapping the front facing with noncombustible facing material.

Nails or Wood Screws

Nailing Flanges

Figure 10 - Attaching Fireplace to Wall Studs

Figure 9 - Rough Opening for Installing in Corner

107034

Continued

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

INSTALLATION

Continued

Mantel Clearances for Built-In Installation

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

• raise the mantel to an acceptable height

• remove the mantel

OPTIONAL MANTEL INSTALLATION

Note:

Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installation. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Accesso- ries, pages 28 and 29).

1. Unscrew four brass screws that attach

top louver to fireplace. Remove louver from fireplace and set aside.

2. Place fireplace on wood base.

3. Place mantel around fireplace/base

assembly.

4. Assemble brass trim kit. See Assem-

bling Brass Trim.

5. Firmly snap brass trim kit on shoulder

screws. Shoulder screws are located on fireplace cabinet (see Figure 12).

6. Align brass trim kit for flush fit around

opening.

7. Use two 3" wood screws provided and

attach fireplace base to wooden base (see Figure 12).

8. Remove brass trim kit and mantel. Be careful not to damage wall or mantel.

9. Place wood base next to wall at installation location.

10.

Attach wood base to floor with two 1 3/4" black screws provided (see Figure 13). If the floor is concrete use anchor method (see Attaching Wood Base to Solid Floor, page 13).

11. Install gas line. See Connecting T o Gas Supply, page 13.

12. Check for leaks. See Checking Gas Connections, page 15.

13. Place mantel around fireplace. Be careful not to damage wall or mantel.

14. Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 12).

15. Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for the brass louvers (see Figure 12).

16. Reinstall top brass louvers.

Note:

All vertical measurements are from top of fireplace opening to bottom of mantel shelf. All measurements are in inches.

Side of Firebox

Figure 11 - Minimum Mantel Clearances for Built-In Installation

10" 8" 6" 2 1/2"

Mantel Shelf

13"

16"

19"

21"

Hole for 3" wood screw for attaching fireplace to mantel

Shoulder Screws

Hole for 3" wood screw

Assembled Brass Trim

Figure 12 - Attaching Brass Trim to Fireplace

1 3/4" Screw

Figure 13 - Attaching Wood Base to Floor

for attaching fireplace to wooden base

Wood Base

Assembling Brass Trim (Brass trim shipped with mantel)

1. Remove packaging from three remaining pieces of brass trim.

2. Locate two adjusting plates with set screws, and two shims in the hardware packet.

3. Align shim under adjusting plate as shown in Figure 14, page 11.

4. Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 14, page 11).

5. Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 14, page 11).

6. While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set brass assembly aside for later installation.

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

INSTALLATION

Continued

Top Brass Trim

Set Screws

Adjusting

Plate

Figure 14 - Assembling Brass Trim

INSTALLING BLOWER ACCESSORY GA3400T

Removing Upper Louver Assembly

To install the blower accessory, you must first remove the upper louver assembly.

1. Lift screen off heater and remove log set.

2. Remove 2 screws from each side of branch support and pull branch support out (see Figure 15).

3. Remove 4 brass-plated screws from louver assembly (see Figure 16). Save these screws.

4. Pull louver assembly straight out from the cabinet. Be careful not to scratch the paint. Set louver assembly and screws aside.

Blower Bracket Mounting Holes

Slot

Shim

Mitered Edge

Side Brass Trim

Installing Blower Assembly

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

CAUTION: Verify proper

operation after servicing.

Note:

If you are using a mantel with your

heater, use the following instructions. If your heater is built-in, see For Built-In In- stallation on page 12.

1. Install snap bushings found in hardware kit into both holes in rear of valve cover shield.

2. Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly.

Screw

Switch

Blower Bracket Assembly

Power Cord

Wire Harness

3. Note the wire locations on back of AUTO/OFF/ON switch. The terminals on back of switch are numbered 1, 2, and 3. Carefully remove red wire from terminal 3 and blue wire from terminal 1. Black wire can remain on middle terminal 2 (see Figure 16).

4. Carefully disconnect green and white wires at their insulated connectors.

5. In top of the heater cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly . Attach blower bracket assembly to the outer casing with 4 #10 screws provided (see Figure 16).

6. Route the wire harness through the hole in left side of baffle. Pull wire harness through lower opening on the side of the valve shield. (see Figure 16).

7. Insert the 4 wire harness into one of the round holes in the rear of the valve cover shield and through the rectangular hole in the front of shield (see Figure 16).

Wiring Routing Hole in Baffle

Baffle

Snap Bushing

Upper Louver Assembly

Branch Support

Figure 15 - Removing Upper Louver Assembly and Branch Support

107034

3 2 1

Red

Blue

Switch Plate

Wire Harness

Valve Cover Shield

Figure 16 - Installing Blower Bracket Assembly

For more information, visit www.desatech.com

Continued

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

INSTALLATION

Continued

8. Reconnect red wire to switch position

3. Reconnect blue wire to switch position 1. Reconnect green and white wires.

9. Install the switch plate on the valve cover shield with 2 #10 screws provided (see Figure 17). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 16, page 11). Plug fan kit into 120-Volt grounded power supply and test operation.

Note:

When switch is in the AUTO position, the fan will start after the heater has run for a few moments. The fan will continue to run for several moments after the heater has been turned off. When switch is in the ON position, the fan will run until turned to OFF . Reinstall upper louver assembly (see Figure 15, page 11) and branch support. Close lower louver door.

Valve Cover Shield

1. Install a snap bushing found in hardware kit into one of the holes found rear of valve cover shield. The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2. Follow steps 2 through 6 in Installing Blower Assembly, page 11.

(see Figure 20). Set the cable bundle between the burner bracket and outer casing, away from the burner.

5. Test to make sure the blower is working properly .

6. Reinstall upper louver assembly (see Figure 15, page 11) and close lower louver .

3. A licensed electrician must follow the wiring diagram to connect incoming electrical supply to fan kit wiring harness (see Figure 19).

4. Plug power cord to the outlet receptacle (not provided) as shown in Figure 20. Wind the extra cable in power cord and and tie it up with the plastic wire strap

Fan Switch

(Auto/Off/On)

Auto

Off

110/115

V.A.C.

Black

White

Green

Red

Figure 19 - Wiring Diagram For Blower Accessory Built-In Installation

Blue

Thermostat

Extension Cord

Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole receptacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An undersized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet.

Switch

(N.O.)

Blue

Blower

Motor

Red

White

Green

Switch

Screw

Plate

Figure 17 - Installing Switch Plate to Valve Cover Shield

Fan Switch

(Auto/Off/On)

Auto

Off

110/115

V.A.C.

Black

White

Green

Red

Blue

Thermostat

Switch

(N.O.)

Blue

Red

White

Green

Blower

Motor

Figure 18 - Wiring Diagram For Blower Accessory Standard Installation

For Built-In Installation

WARNING: A licensed electrician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of heater.

Blower Bracket Assembly

Screw

Switch

Blue

Power Cord

Red

Outlet Receptacle (Not Supplied)

Switch

Plastic Wire Harness

Wire

Strap

Clamp Connector (not included)

Figure 20 - Installing Blower Bracket Assembly

Wire Harness

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

INSTALLATION

Continued

Attaching Wood Base to Solid Floor

For attaching base to solid floors (concrete or masonry)

Note:

Floor anchors and mounting screws are in hardware package. The hardware package is provided with fireplace.

1. Drill holes at marked locations using

5/16" drill bit. For solid floors (concrete or masonry), drill at least 1" deep.

Fold floor anchor as shown in Figure 21.

3. Insert floor anchor (wings first) into

hole. Tap anchor flush to floor.

4. Insert mounting screws through base

and into floor anchors.

5. Tighten screws until base is firmly fas-

tened to floor.

Figure 21 - Folding Anchor

CONNECTING TO GAS SUPPLY

WARNING: This appliance re-

quires a 45° male flare fitting 5/8"18 UNF (Unified National Fine Thread) inlet connection and the flexible gas line provided.

WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.

The installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pressure, fireplace regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 22. Pointing the vent down protects it from freezing rain or sleet.

CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" or greater diameter to allow proper gas volume to fireplace. If pipe is too small, undue loss of pressure will occur.

External Regulator

Propane/LP Supply Tank

Vent Pointing Down

Figure 22 - External Regulator with Vent Pointing Down

From External Regulator (11" W.C.** to 14" W.C. Pressure)

Tee Joint

Installation must include a equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from fireplace (see Figure 23).

IMPORTANT:

Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged fireplace valves.

CAUTION: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

We recommend that you install a sediment trap in supply line as shown in Figure 23. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into fireplace controls. If sediment trap is not installed or is installed wrong, fireplace may not run properly.

CSA/AGA Design-Certified Equipment Shutoff Valve with 1/8" NPT Tap*

Approved Flexible Gas Hose

Gas Control

CAUTION: Never connect fireplace directly to the propane/LP supply. This fireplace requires an external regulator (not supplied). Install the external regulator between the fireplace and propane/LP supply.

107034

Pipe Nipple

Cap

Sediment Trap

Figure 23 - Gas Connection

3" Minimum

*Purchase the optional CSA/AGA design-certified equipment shutoff valve from your dealer. See Accessories, pages 28 and 29.

**Minimum inlet pressure for purpose of input adjustment.

For more information, visit www.desatech.com

Continued

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

INSTALLATION

Continued

CONNECTING FIREPLACE TO GAS SUPPLY

Installation Items Needed

• Phillips screwdriver

• sealant (resistant to propane/LP gas, not provided)

1. Remove fireplace screen. Remove two

screws that hold fireplace screen in place for shipping. These screws are located near top of screen. Discard screws. Lift fireplace screen up and pull out to remove.

2. Remove screws that attach branch sup-

port to fireplace (see Figure 24). Carefully lift up branch support and remove from fireplace (see Figure 24).

3. Route flexible gas line (provided by

installer) from equipment shutoff valve into fireplace through side or rear access holes in outer casing. Route flexible gas supply line through fireplace access holes in outer casing.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.

Shoulder Screw

Screen

Branch Support

Figure 24 - Removing Branch Support From Fireplace

NOTICE: Most building codes do not permit concealed gas connections. A flexible gas line (see Figure 25) is provided to allow accessibility from the fireplace. The flexible gas supply line connection to the equipment shutoff valve should be accessible.

4. Apply pipe joint sealant lightly to male threads of gas connector attached to flexible gas line (see Figure 25). Connect flexible gas line to flexible gas line attached to gas valve of fireplace (see Figure 25).

5. Check all gas connections for leaks. See Checking Gas Connections, page 15.

6. Replace branch support back into fireplace. Feed flexible gas line into fireplace base area while replacing branch support. Make sure the entire flexible gas line is in fireplace base area. Reattach branch support to fireplace with screws removed in step 2.

Equipment shutoff valve

To Gas Supply

Figure 25 - Attaching Flexible Gas Lines Together

➞

Flexible Gas Line from Equipment Shutoff Valve Provided by Installer

Gas Connector

Flexible Gas Line from Fireplace Gas Valve Provided with Fireplace

➞

To Fireplace Gas Valve

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

INSTALLATION

Continued

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.

CAUTION: Make sure external regulator has been installed between propane/LP supply and fireplace. See guidelines under

necting to Gas Supply

, page 13.

Con-

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 26).

2. Pressurize supply piping system by either using compressed air or opening propane/LP supply tank valve.

3. Check all joints from propane/LP supply tank to equipment shutoff valve (see Figure 27). Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Open

Equipment Shutoff Valve

Figure 26 - Equipment Shutoff Valve

POSITION

OFF

POSITION

Closed

Pressure Testing Fireplace Gas Connections

Open equipment shutoff valve (see Figure 26).

2. Open propane/LP supply tank valve.

3. Make sure control knob of fireplace is in the OFF position.

4. Check all joints from equipment shutoff valve to thermostat gas valve (see Figure 27). Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light fireplace (see Operating Fire- place, pages 18 through 20). Check all other internal joints for leaks.

7. Turn off fireplace (see T o Turn Off Gas to Appliance, page 19).

8. Replace front panel.

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect fireplace and its individual equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage fireplace regulator.

2. Cap off open end of gas pipe where equipment shutoff valve was connected.

3. Pressurize supply piping system by either using compressed air or opening propane/LP supply tank valve.

4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

Propane/LP Supply Tank

Equipment Shutoff Valve

Figure 27 - Checking Gas Joints Shown with Optional Mantel

107034

Continued

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

INSTALLATION

Continued

OPTIONAL WIRELESS HANDHELD REMOTE CONTROL ACCESSORIES (GHRC Series & GHRCTA Series)

Installing Receiver

1. Remove screws.

2. Disconnect switch wires from the control valve.

3. Remove switch plate (see Figure 28). Discard switch plate after removing. Save the screws.

4. Locate the battery clip mounted on the back of the receiver (see Figure 29).

5. Slide 9-volt battery (not included) through the clip.

6. Attach the terminal wires to the battery (see Figure 29).

7. Connect wires as shown in Figure 30.

8. Install remote receiver unit onto gas heater base using the two screws removed in step one (see Figure 30).

Screw

Switch Plate

Red Wire

Black Wire

Figure 28 - Switch Plate and Wiring Harness

Receiver

Black Wire

Wire Harness*

Wires from Valve

Black Wire

Figure 30 - Installing Remote Receiver

Red Wire

* Wire harness provided in the fireplace hardware pack.

Installing 9-Volt Battery in HandHeld Remote Control Unit

1. Remove battery cover on back of remote control unit.

2. Attach terminal wires to the battery (not included). Place battery into the battery housing.

3. Replace battery cover onto remote control unit.

Terminal Wires

9-Volt Battery

Figure 31 - Installing Battery in HandHeld Remote Control Unit (GHRC Series)

Battery Cover

Remote Control Unit

Battery Housing

OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1

WARNING: Read and follow installation instructions. Installation should be done by a qualified installer familiar with lowvoltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

Connect one terminal of 25 ft. wire to bottom contact of switch (see Figure 33, page 17).

2. Connect remaining wire terminal to the “TH” terminal on the control valve. Make sure that wire terminals are in the positions on your unit as pictured in Figure 33 on page 17. If wires are not “crossed” the thermostat will not work.

3. Route the 25 ft. wire to a convenient location to mount your thermostat (no outside wall). may be shortened but must not be lengthened.

The thermostat should be mounted 54" above the floor in a location where there is good air circulation. A void heat sources such as lamps, direct sunlight, fireplace, or heat and air conditioning ducts.

4. Gently remove the cover of the thermostat from the base. Grasp the sides of the cover firmly and pull to separate from the base.

5. Feed the electrical wires through the rectangular slots on each side of the base (see Figure 34, page 17).

WARNING: Do not connect the thermostat to a power source. Electrical shock and/or a fire hazard will occur.

IMPORTANT:

The wire

Terminal Wires

Battery Clip

9-Volt Battery

Figure 29 - Attaching Battery to Receiver For more information, visit www.desatech.com

Figure 32 - Installing Battery in Hand-Held Remote Control Unit (GHRCTA Series)

Remote Control Unit

107034

OWNER’S MANUAL

INSTALLATION

Continued

6. Connect one bare wire end to each terminal (“W” and “R”) of the thermostat base (see Figure 35).

7. Install the base onto the wall with the provided screws.

8. Move the temperature adjustment back and forth to insure the bimetal is free from restrictions.

9. Replace the cover onto the base. (Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation).

10. Set switch on heater to Auto position.

11. Set the temperature adjustment to the desired setting. This thermostat has been electronically calibrated at the factory. No adjustment or leveling is necessary .

Switch on Gas Heater

AUTO

OFF

Figure 33 - Connecting Wire Terminals

One terminal of 25 ft. wire

Control Valve

To Wall Thermostat or Switch

Terminal “W”

Terminal “R”

Figure 35 - Thermostat Base Terminals “W” and “R”

To Wall Thermostat or Switch

OPTIONAL WALL SWITCH GWMS2

WARNING: Read and follow installation instructions. Installation should be done by a qualified installer familiar with lowvoltage wiring procedures.

WARNING: Do not connect this switch to any electrical source! Electrical shock and/or fire hazard will occur.

Connect one terminal of 25 ft. wire to bottom contact of switch (see Figure 33)

2. Connect remaining wire terminal to the “TH” terminal on the control valve. Make sure that wire terminals are in the positions on your unit as pictured in Figure 33. If wires are not “crossed” the thermostat will not work.

Route the 25 ft. wire to a convenient location to mount your wall switch (no outside walls).

WARNING: Do not connect the switch to a power source. Electrical shock and/or fire hazard will occur.

IMPORTANT:

but must not be lengthened.

4. Connect one bare wire end to each of the terminals of the provided wall switch.

5. Install the wall switch and cover in the wall.

The wire may be shortened

Feed wires through rectangular slots

Figure 34 - Back View of Thermostat Base

107034

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly .

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHA T TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

•

Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Ne ver use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part

has been under water . Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING: You must operate this fireplace with the fireplace screen in place. Make sure fireplace screen is installed before running fireplace.

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Open window to vent smell. This will only last a few hours.

1. STOP! Read the safety information, column 1.

2. Make sure equipment shutoff valve is fully open.

3. Set switch in OFF position.

WARNING: Burner will come on automatically within one minute when the selector switch is in the ON position after the pilot is lit.

4. Press in and turn control knob clockwise to the OFF position.

5. Wait f ive (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information. If you don’t smell gas, go to the next step.

6. Press in and turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 36).

Note:

You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

7. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

Note:

If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repair s are made, light pilot with match. T o light pilot with match, see Manual Light- ing Procedure on page 19.

8. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

• If control knob does not pop out

when released, contact a qualified service person or gas supplier for repairs.

Note:

If pilot goes out, repeat steps

4 through 8.

9. Slightly push in and turn control knob counterclockwise to the ON position.

10. Wait one minute and switch selector switch to the ON position to light burner.

11. Set flame adjustment knob to any level between HI and LO.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position.

Selector Switch in OFF Position

Figure 36 - Control Knob and Ignitor Button Location (Shown as Supplied, No Control Options)

For more information, visit www.desatech.com

AUTO OFF ON

Ignitor Button

Control Knob

Flame Adjustment Knob

107034

OWNER’S MANUAL

OPERATING FIREPLACE

Continued

Pilot Burner

Figure 37 - Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1. T urn control knob clockwise to the OFF position.

2a. Set selector switch in the OFF position. 2b. If Using Optional Hand-Held Re-

mote: Set selector switch in the OFF position to keep from draining battery .

Shutting Off Burner Only (pilot stays lit)

You may shut off the burner and keep the pilot lit by doing one of the following:

• Turn control knob clockwise

to the PILOT position.

•

Use remote control manual OFF button.

• Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 6 under Lighting Instructions, page 18.

2. Depress control knob and light pilot with match.

3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11, page 18.

Ignitor Electrode

OPTIONAL REMOTE

OPERATION

Note:

All remote control accessories must be purchased separately (see Accessories, pages 28 and 29). Follow installation instructions on page 16 of this manual.

Thermostat Control Operation

(Optional GHRCTA Series Only) The thermostat control setting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burner will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

For wall thermostat operation, follow instruction supplied with thermostat accessory GWMT1. For wall switch operation follow instructions supplied with GWMS2.

NOTICE: You must light the pilot before using the hand-held remote control unit. See

Instructions

on page 18.

1. After lighting, let pilot flame burn for

about one minute. T ur n control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position. burner may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the bur ner on and off with the hand-held remote control unit.

REMOTE OFF ON

Lighting

Note:

The

Control Knob

IMPORTANT:

Do not leave the selector switch in the REMOTE position when the pilot is not lit. This will drain the battery.

IMPORTANT:

Be sure to press the ON/OFF buttons on the hand held remote control unit for up to 3 seconds to assure proper operation.

GHRC Series Operation:

2a. Press the ON/OFF button to turn the

burner on and off. When turning burner off, the pilot will remain lit.

GHRCTA Series Operation:

2b. Press the AUTO/ON/OFF button on

the hand-held remote control (see Figure 39, page 20). The lights to the left of the button will show AUTO, ON, or OFF.

• In the ON mode, the burners will

ignite. The heater is in manual mode when ON is lit.

• In the A UTO mode, the thermostat

in the hand-held remote unit controls the room temperature. To increase the room temperature, pr ess the top arrow of the TEMP b utton. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer.

Flame Adjustment Knob

107034

Selector Switch in Remote Position (Optional Remote Control)

Figure 38 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

Continued

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

OPERATING FIREPLACE

Continued

IMPORTANT:

has been specially engineered to take an air temperature sample every 5.5 minutes in the auto mode. It will not respond immediately to the temperature setting being turned up or down.

IMPORT ANT :

control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

3. To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit.

IMPORTANT:

manually turn the control knob on the heater to the OFF position.

Shows Temperature Setting

The Log Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected

Figure 39 - Thermostat Hand-Held Remote Control Unit Selections (GHRCTA Series Only)

This remote control

The hand-held remote

To turn the pilot off,

Increases Room Temperature in AUTO Mode

Decreases Room Temperature in AUTO Mode

Turns Burners On or Off and Allows You to Choose the Auto Setting

GWMT1 WALL

MOUNTED

THERMOSTAT

(OPTIONAL)

Make sure the heater switch is on AUTO and set the temperature adjustment on wall thermostat to the desired setting. The thermostat has been electronically calibrated at the factory and requires no adjustment or leveling.

Upon installation, the thermostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation. See installation instructions on pages 16 and 17 of this manual.

GWMS2 WALL

MOUNTED SWITCH

(OPTIONAL)

Make sure the heater switch is on AUTO. This wall switch works just like the conventional light switch. Flip the switch up for on and down for off.

Note:

Make sure that this switch is not in a position to be mistaken for a light switch. This may result in the heater being inadvertently turned on without the proper precautions being taken. See installation instructions on page 17 of this manual.

OPERATING BLOWER

This blower has three settings: ON, OFF, and AUTO. In the ON position, the blower will operate constantly. In the OFF position, the blower will not operate. In the AUTO position, the blower will start when the thermostat senses a sufficient increase in firebox temperature.

Note:

Your fireplace and thermostat blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.

Note:

It is safe to operate fireplace with blower turned off. However, the blower helps distribute heated air from the fireplace.

Auto/Off/On Switch

Figure 40 - Auto/Off/On Switch

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 41 shows a correct pilot flame pattern. Figure 42 shows an incorrect pilot flame pattern. The incorrect pilot flame is not properly heating the thermocouple. When the thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 42.

• turn heater off (see To Turn Off Gas to Appliance, page 19)

•

see Troubleshooting, pages 22 through 24

Pilot Burner

Thermocouple

Figure 41 - Correct Pilot Flame Pattern

Pilot Burner

Thermocouple

Figure 42 - Incorrect Pilot Flame Pattern

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

INSPECTING BURNER

Continued

BURNER FLAME PATTERN

Figure 43 shows a correct burner flame pattern. Figure 44 shows an incorrect burner flame pattern. The incorrect burner flame pattern shows sporadic, irregular flame tipping. It also shows the flame consistently higher than one inch above the log.

Note:

When using the fireplace the first time, the flame will be orange for approximately one hour until the log cures.

If burner flame pattern is incorrect, as shown in Figure 44

• turn fireplace off (see To Turn Off Gas to

Appliance, page 18)

• see T roubleshooting, pages 22 through 24

Top of Flame About One Inch Above Log

Figure 43 - Correct Burner Flame Pattern

Figure 44 - Incorrect Burner Flame Pattern

CLEANING AND MAINTENANCE

WARNING: Turn off fireplace

and let cool before cleaning.

CAUTION: You must keep control areas, burner, and circulating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2. Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 45).

3. Blow air through the ports/slots and holes in the burner.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the injector holder.

6. In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 46). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Injector Holder

Ports/Slots

Burner Tube

Primary Air Inlet Holes

Figure 45 - Injector Holder On Outlet Burner Tube

Pilot Air Inlet Hole

Pilot Assembly

Figure 46 - Pilot Inlet Air Hole

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air

to clean.

Exterior

• Use a soft cloth dampened with a mild

soap and water mixture. Wipe the cabinet to remove dust.

107034

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

TROUBLESHOOTING

Note:

For additional help, visit DESA

International’s technical service web site at www.desatech.com.

Note:

All troubleshooting items are listed in

order of operation.

OBSERVED PROBLEM

When ignitor button is pressed, there is no spark at ODS/pilot

When ignitor button is pressed, there is spark at ODS/pilot but no ignition

WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.

POSSIBLE CAUSE

1. Ignitor electrode not connected to ignitor cable

2. Ignitor cable pinched or wet

3. Piezo ignitor nut is loose

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned wrong

1. Gas supply turned off or equipment shutoff valve closed

2. Control knob not in PILOT position

3. Control knob not pressed in while in PILOT position

4. Air in gas lines when installed

5. Depleted gas supply

6. ODS/pilot is clogged

7. Gas regulator setting is not correct

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry

3. Tighten nut holding piezo ignitor to base panel of log set. Nut is located behind base panel

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace piezo ignitor

7. Replace piezo ignitor

1. Turn on gas supply or open equipment shutoff valve

2. Turn control knob to PILOT position

3. Press in control knob while in PILOT position

4. Continue holding down control knob. Repeat igniting operation until air is removed

5. Contact local propane/LP gas company

6. Clean ODS/pilot (see Cleaning and Maintenance, page 21) or replace ODS/ pilot assembly

7. Replace gas control

ODS/pilot lights but flame goes out when control knob is released

For more information, visit www.desatech.com

1. Control knob not fully pressed in

2. Control knob not pressed in long enough

3. Equipment shutoff valve not fully open

4. Pilot flame not touching thermocouple,

5. Thermocouple connection loose at con-

6. Thermocouple damaged

7. Control valve damaged

which allows thermocouple to cool, causing pilot flame to go out. This problem could be caused by one or both of the following: A) Low gas pressure B) Dirty or partially clogged ODS/pilot

trol valve

www.desatech.com

1. Press in control knob fully

2. After ODS/pilot lights, keep control knob pressed in 30 seconds

3. Fully open manual shut-off valve

4. A) Contact local propane/LP gas company

B) Clean ODS/pilot (see Cleaning and Maintenance, page 21) or replace ODS/ pilot assembly

5. Hand tighten until snug, then tighten 1/4 turn more

6. Replace thermocouple

7. Replace control valve

107034

TROUBLESHOOTING

Continued

OWNER’S MANUAL

OBSERVED PROBLEM

Burner does not light after ODS/pilot is lit

Delayed ignition burner

Burner backfiring during combustion

Slight smoke or odor during initial operation

POSSIBLE CAUSE

1. Burner orifice clogged

2. Inlet gas pressure is too low

3. Burner orifice diameter is too small

4. Thermopile leads disconnected or improperly connected

5. Burners will not come on in remote position

1. Manifold pressure is too low

2. Burner orifice clogged

1. Burner orifice is clogged or damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

3. Residues from manufacturing processes and logs curing

REMEDY

1. Clean burner (see Cleaning and Maintenance, page 21) or replace burner orifice

2. Contact local propane/LP gas company

3. Replace burner orifice

4. Reconnect leads (see Wiring Diagram, page 25)

5. Replace battery in transmitter and receiver

1. Contact local propane/LP gas company

2. Clean burner (see Cleaning and Mainte- nance, page 21) or replace burner orifice

1. Clean burner (see Cleaning and Mainte- nance, page 21) or replace burner orifice

2. Replace damaged burner

3. Replace gas control

1. Check burner for dirt and debris. If found, clean burner (see Cleaning and Maintenance, page 21)

2. Replace gas control

3. Problem will stop after a few hours of operation

Moisture/condensation noticed on windows

Heater produces a whistling noise when burner is lit

White powder residue forming within burner box or on adjacent walls or furniture

Remote does not function

1. Not enough combustion/ventilation air

1. Turning control knob to HI position when burner is cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orifice

1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. turn into white powder residue

1. Battery is not installed. Battery power is low

www.desatech.com

1. Refer to Air for Combustion and Ventilation requirements (page 5)

1. Turn control knob to LO position and let warm up for a minute

2. Operate burner until air is removed from line. Have gas line checked by local propane/LP gas company

3. Observe minimum installation clearances (see pages 8 through 10)

4. Clean burner (see Cleaning and Mainte- nance, page 21) or replace burner orifice

1. Turn heater off when using furniture polish, wax, carpet cleaners, or similar products

1. Replace 9-volt batteries in receiver and remote control

Continued

107034

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT:

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.

OBSERVED PROBLEM

Heater produces a clicking/ticking noise just after burner is lit or shut off

Heater produces unwanted odors

Heater shuts off in use (ODS operates)

Gas odor even when control knob is in OFF position

Operating heater where impurities in air exist may create odors. Cleaning

POSSIBLE CAUSE

1. Metal expanding while heating or contracting while cooling

1. Heater burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (See ment above)

2. Gas leak. See W arning statement at

top of page

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak. See W arning statement at

top of page

2. Control valve defective

IMPORTANT

state-

REMEDY

1. This is common with most heaters. If noise is excessive, contact qualified service person

1. Open window and ventilate room. Stop using odor causing products while heater is running

2. Locate and correct all leaks (see Check- ing Gas Connections, page 15)

1. Open window and/or door for ventilation

2. Contact local natural gas company

3. Clean ODS/pilot (see Cleaning and Maintenance, page 21)

1. Locate and correct all leaks (see Check- ing Gas Connections, page 15)

2. Replace control valve

Gas odor during combustion

For more information, visit www.desatech.com

1. Foreign matter between control valve

2. Gas leak. See W arning statement at

and burner

top of page

www.desatech.com

1. Take apart gas tubing and remove foreign matter

2. Locate and correct all leaks (see Check- ing Gas Connections, page 15)

107034

OWNER’S MANUAL

SPECIFICATIONS

Btu (Variable) 15,000/26,000 Type Gas Propane/LP Only Ignition Piezo Manifold Pressure 8" W.C. Inlet Gas Pressure (in. of water) *

Maximum 14" Minimum 11"

Dimensions, Inches (H x W x D)

Fireplace (including hood and screws) 25 7/8 x 26 13/16 x 9 3/8 Carton 32 5/8 x 27 3/16 x 11 5/8

Weight, pounds

Fireplace 44 1/2 lbs. Shipping 48 lbs.

* For purposes of input adjustment

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burner will have delayed ignition

• fireplace will not produce specified heat

• propane/LP gas supply may be low

When Gas Quality Is Bad

• pilot will not stay lit

• burner will produce flames and soot

• fireplace will backfire when lit You may feel your gas pressure is too low or

gas quality is bad. If so, contact your local propane/LP gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting.

If so, contact DESA International’s Technical Service Department at 1-800-323-5190.

You can also visit DESA International’s technical services web site at

www.desatech.com.

WIRING DIAGRAM

Auto

Off On

Thermopile

Switch

Black

Red

White

TPTH TH

Gas Control

TPTH

REPLACEMENT PARTS

Note:

Use only original replacement parts.

This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s) call DESA International’s Technical Service Department at 1-800-323-5190 for referral information.

When calling DESA International, have ready

• your name

• your address

• model and serial numbers of your fireplace

• how fireplace was malfunctioning

• type of gas used (propane/LP or natural

gas)

• purchase date

Usually, we will ask you to return the defective part to the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s) call DESA International’s Parts Department at 1-800-972-7879 for referral information.

When calling DESA International, have ready

• model number of your fireplace

• the replacement part number

107034

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

ILLUSTRATED PARTS BREAKDOWN

VMH26PRA

22 39

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

PARTS LIST

VMH26PRA

This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under Replacement Parts on page 25 of this manual.

KEY NO. PART NO. DESCRIPTION QTY.

1 102633-02CK Outer Casing Top 1 2 102624-02 Outer Casing 1 3 099230-02 Shoulder Screw 14 4 098304-01 Screw, #10 x 3/8" 17 5 107178-02 Burner 1 6 103209-03 Louvered Door 1 7 102635-02CK Left and Right Side Front 2 8 103209-01 Brass Top Louver 1 9 104281-01CJ Firebox Hood 1 10 102638-01 Firebox Top 1 11 103778-01 ODS/Pilot Assembly 1 12 102460-01 Firebox Wrapper 1 13 104322-01 Burner Tube 1 14 104335-01CK Outer Shell Base 1 15 102649-02CK Branch Support 1 16 102445-01 Piezo 1 17 099387-13 Pilot Tube 1 18 098271-07 Ignitor Cable 1 19 107186-01 Injector 1 20 101006-02 Pilot Bracket 1 21 098249-01 Nut, M5 2 22 103781-02 Gas Valve 1 23 102639-01 Baffle 1 24 101628-01 Flexible Connector 1 25 104305-01 Control Shield 1 26 103295-03CJ Screen Assembly 1 27 107153-01 Log Set Kit 1 28 104313-01 Right Hinge 1 29 104313-02 Left Hinge 1 30 M10908-2 Hinge Screws 4 31 103734-01 Burner Support 2 32 M11084-26 Hex Head #10 x .38 25 33 097809-02 Connector, Male 1 34 101629-01 Bushing 1 35 101629-02 Bushing 1 36 M12461-26 Gas Valve Screws 4 37 103587-02CK Plate, Switch 1 38 099998-01 Switch, Fan 1 39 098264-02 Connector, Male 1 40 103284-03 Wire Harness 1

107034

PARTS AVAILABLE — NOT SHOWN

104319-04 Video 1 103877-01 Lighting Instructions Plate 1 100563-01 Warning Plate 1 103470-02 Hardware Package 1

For more information, visit www.desatech.com

VMH26PRA

COMPACT CLASSIC HEARTH FIREPLACE

ACCESSORIES

Purchase these fireplace accessories from your local dealer. If they cannot supply these accessories call DESA International’s Sales Department at 1-800-458-2472 for referral information. You can also write to the address listed on the back page of this manual.

THERMOSTATICALLY CONTROLLED BLOWER KIT GA3400T

Provides better heat distribution. Makes fireplace more efficient. Automatically turns off and on as needed.

EQUIPMENT SHUTOFF VALVE - GA5010

Equipment shutoff valve with 1/8" NPT tap.

CABINET MANTEL WITH BUILT-IN HEARTH BASE AND TRADITIONAL SQUARE LEG STYLING

Unfinished - GM923U Finished - GM922F

For use with fireplace. A hardwood mantel and hearth base offers compact styling and completes the fireplace look. Available in a stained or an unfinished (ready to stain or paint) Oak Veneer over hardwood. Complete assembly instructions included. Threesided brass trim kit included.

BRASS TRIM KIT - GA6095

Optional four-sided brass trim kit for recessed built-in installations (when unit is raised off of the floor). Provides a finished appearance by covering rough edges of wall opening.

BRASS TRIM KIT - GA6094

(Not Shown)

Optional three-sided brass trim kit for custom and recessed installations (when unit is on the floor). Provides a finished appearance by covering rough edges of wall opening. Included with all mantels.

CABINET MANTEL WITH BUILT-IN HEARTH BASE AND ROUNDED LEG STYLING

Unfinished - GM921U Walnut Finished - GM920F Cherry Finished - GM924F (Appearance May Differ by Model)

For use with fireplace. A hardwood mantel and hearth base offers compact styling and completes the fireplace look. Available in a walnut finished, cherry finished, or an unfinished hardwood, ready to stain or paint. Complete assembly instructions included. Three-sided brass trim kit included.

CORNER MANTEL WITH BUILT-IN HEARTH BASE

Unfinished - GM721U Finished - GM720F

For use with fireplace. Space-saving mantel and hearth base corner design features clean, classic lines. Available in a walnut finish or an unfinished hardwood, ready to stain or paint. Complete assembly instructions included. Three-sided brass trim kit included.

For more information, visit www.desatech.com

107034

OWNER’S MANUAL

ACCESSORIES

Continued

WARMER

COOLER

TEMP

AUTO

OFF

RECEIVER AND HAND-HELD THERMOSTAT REMOTE CONTROL KIT - GHRCT SERIES

For all models. Allows the gas log heater to be operated in a manually or thermostatically controlled mode. You can turn the gas log heater on and off without ever leaving the comfort of your easy chair.

RECEIVER AND HAND-HELD REMOTE CONTROL KIT GHRC SERIES

For all models. Allows the gas log heater to be turned on and off by using a hand-held remote control.

WALL MOUNTED THERMOSTAT KIT - GWMT1

(Not Shown)

For all models. Allows easy wall access to the operation of your gas log heater. This will allow you to thermostatically control your heater with the convenience of a wall switch.

WALL MOUNTED SWITCH KIT - GWMS2

(Not Shown)

For all models. Allows convenient access to the operation of your gas log heater.

CLEANING KIT - CCK

(Not Shown)

Your vent-free gas appliance requires regular cleaning and maintenance to prevent performance problems. This kit gives you the tools and instructions to make it easy to clean all critical areas of your appliance.

107034

For more information, visit www.desatech.com

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model Serial No. Date Purchased

Always specify model and serial numbers when communicating with the factory. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written

warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE PROPANE/LP GAS COMPACT CLASSIC HEARTH® FIREPLACE

DESA International warrants this product to be free from defects in materials and components for four (4) years and five (5) years on stainless steel burners from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this fireplace to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The fireplace MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective fireplace will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO FOUR (4) YEARS ON ALL COMPONENTS AND FIVE (5) YEARS ON STAINLESS STEEL BURNERS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. For information about this warranty write:

INTERNATIONAL

2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004

www.desatech.com

107034 01

NOT A UPC

107034-01 REV. B 09/00

Vanguard Heating VMH26PRA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual