VANCO VPW-280754 User Manual
HDMI® HDBaseT MATRIX
4X4 OVER SINGLE UTP (70M/230FT)
PRODUCT MANUAL
Vanco Part Number
VPW-280754
www.vanco1.com • 888.769.4156
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before
connecting, operating or adjusting this product.
Please keep this manual for future reference.
This product is 100% inspected and tested in the United States
to verify HDMI performance parameters.
WARNING
1. Do not expose this unit to water, moisture,
or excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating, do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms, or
when not used for an extended period
of time. A surge protector is strongly
recommended.
8. Protect the power cord from being walked
on or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
2
www.vanco1.com
FEATURES
Vanco Powered by Wyrestorm HDMI 4x4 HDBaseT (70m/230ft) Matrix is an HD 4 input/4 output switching and
extension system. Have 4 sources displayed simultaneously on any display or have a single source duplicated on
multiple displays, exibility for the perfect solution. Features HDBaseT (70m/230ft) technology, which allows for
audio, video, IR, and Power over Cable to be transferred over a single Cat5e/6/7 cable up to 230 feet. Simple plug
and play solution that allows each output with the ability to extend HDMI signal up to 230 feet over a single category
5e or 6 cable in conjunction with the Vanco Powered by Wyrestorm HDBaseT (70m/230ft) receiver VPW-280773
(sold separately). Features additional HDMI output per UTP output for exibility or mirroring capability, able to
be utilized as an 4x8 matrix unit. With an output bandwidth of 6.75 Gbps, the VPW-280754 is capable of full
1080p HD video and HD multi-channel audio distribution with simple control using the front panel or remotely via
IR Receivers at display locations. Also features EDID management system, which allows and encourages device
communication compatibility for seamless integration. Includes RS232 connectivity for rmware updates or third
party integration for control and switching.
Vanco Powered by WyreStorm HDMI® 4 x 4 HDBaseT
(70m/230 ft) Matrix
Part # VPW-280754
y Allows any 4 HDMI input to be distributed
independently and simultaneously over distances
of up to 70m (230ft) to any of the 4 HD output
displays connected to the matrix, regardless of
HDCP encryption, with discrete IR control
y Features Duplicate HDMI ports on each UTP
output for connection to HDMI sources such as an
additional display (effectively doubling the outputs),
AV Receiver, or alternative mode of extension
y Each HDMI port also supports DVI signals
y Each output is able to show any connected source
simultaneously regardless of whether the input
carries HDCP encryption
y HDCP compliant with constant feed to prevent
screen drop-outs
y Reads and copies EDID from connected devices
with additional EDID configuration through
customizable DIP switch settings
y The same robust transmission technology as full
HDBT that is far more resistant to electrostatic
interference than conventional non-HDBT
distribution
y HDMI v1.4 with full 3D compatibility with frame
sequential (Blu-Ray) and interlaced Stereoscoptic
(satellite/cable broadcasts)
y Central RS232 control – fully compatible with all
market leading control systems with full integration
protocols available for AMX, Control 4, Crestron,
Red Eye, Nevo, RTI, Control FX, Savant, Bit Wise
y LAN control – with Control 4 LAN protocols
y Wide range, two way discrete IR control between
source and display and vice versa (38 KHz to 56
KHz frequency)
y 2K resolution (compared to 4k resolution with full
HDBaseT)
y 36bit Deep Color supported
y 6.75 Gbps bandwidth range/signaling rate
y 70m (230 ft) distance range of matrix/extenders
under perfect transmission conditions
y Each Output port can be fed to multiple displays
(cascaded)
y Supports all high definition resolutions up to and
including 1080p and standard video formats
y Choose from 5 switching modes – infrared remote
control, front panel buttons, local IR, IR call-back,
and RS232
y Simple switching remote control included, which
can also be learned into a universal remote
handset to allow the control of multiple devices
from one handset
y 4 x IR 3.5mm mini-jack ports for each output
y Additional infrared extension port for longer IR
connections
y Dimensions: 17.3” W x 1.6” H x 6.6” D
888.769.4156
3
SPECIFICATIONS
Dimensions (WxHxD): ............................................... 440mm / 17.3” (W) 42mm / 1.6” (H) 168mm / 6.6”
(D)
Weight (Kg): ............................................................ 2.0 Kg / 4.4lbs
Operating Temperature Range: ................................... 5 to 90 % RH (no condensation)
Operating Humidity Range: ........................................ 0 to +35°C (32 to +95°F)
Video Amplier Bandwidth: ......................................... 6.75Gbps
Input Video Signal: .................................................... 0.5-1.0 volts p-p
Input DDC Signal: ...................................................... 5 volts p-p (TTL)
Maximum Single Link Range: ...................................... 1080p 36bit Deep Color
Transmission distance: .............................................. 1080p signal up to 70m / 230ft - using VPW-
280773 Display Receiver (Under perfect transmission conditions including straight cable runs with no
electrical interference, bends, kinks, patch panels or wall outlets.)
Video Format Supported: ............................................ VESA: 640x480, 800x600,1024x768, 1280x1024,
1600x1200, 1920x1200 DTV/HDTV: 480i/576i/480p/576p/720p/1080i/1080p
Output Video: ............................................................ HDMI v1.4 with full 3D compatibility with Frame
Sequential (Blu-ray) and Interlaced Stereoscoptic (satellite/cable broadcasts)
Audio Format Supported: ............................................ DTS-HD Master Audio, Dolby True HD, multi-channel
5.1, 7.1, stereo
Power Supply: .......................................................... 100-240V AC
Power Consumption: ................................................. 35 Watts (max.)
Rack Space Required: ................................................ 1U
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following items are
contained in the shipping carton:
• (1) Vanco Powered by Wyrestorm VPW-280754 Matrix Unit
• (1) Power Supply for Matrix Unit (100-240V AC)
• Product Manual
• Mounting brackets with screws
• (1) IR Remote
• (1) IR RX Extension Cable
• (4) IR TX emitters (small for input source)
• (4) IR RX receivers (larger for displays)
4
www.vanco1.com
CONNECT AND OPERATE
Cable Box BluRay® Player
Console
Duplicate HDMI
Mirrored outputs
Game
Apple TV
1. Connect up to 4 sources such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite
Receiver, etc. to the HDMI inputs on the unit. Do not hotplug! Insert and extract cables carefully with the
power SWITCHED OFF. Connecting and disconnecting while the unit is powered can result in damage to
circuitry.
2. Connect the output UTP ports and/or HDMI output ports, starting with output 1, to the VPW-280773
display receivers (sold separately) (using well terminated or pre-terminated Cat5e/6 cables no longer than
230 ft)
3. If utilizing UTP, connect the output HDMI ports of the VPW-280773 display receivers (sold separately)
to high-denition displays such as an HDTV or HD projector that use HDMI inputs. Note that high-speed
HDMI cables are recommended for the distances that are required for each connection.
4. Plug in IR transmitters to the back of the Matrix Selector Switcher unit (IR TX), the transmitters are
labeled IR TX, place in front of the IR receiver of the source, ensure that each emitter is placed in front of
the IR receiver eye. Double-sided adhesive tape provided.
5. Plug in IR receivers to the port of the VPW-280773 display receivers (sold separately) ,the receivers are
labeled IR RX, use provided double-sided adhesive tape to stick emitters at each display at a desired place
that will receive a remote signal.
6. For power, plug in the source rst, followed by the Vanco Powered by Wyrestorm Matrix Selector Switcher
(power supply included), followed by the HDBaseT display receivers, followed by each output connected.
7. Power on each device in the same sequence.
At this point each display connected should display the assigned source (input 1 at default when powered
on initially), scroll through each of the sources on each display to ensure everything is in working order. Use
included IR remote at each display receiver to test switching function between sources and IR function itself.
If a display is having difculty receiving a signal, access the display’s menu and adjust the resolution (lowest to
highest until signal is displayed). A 24 Hz vertical refresh rate may work better than 60 Hz or higher. If the IR
remote function is not responding, check the emitters to ensure they are placed correctly and are plugged into
the correct IR jacks on the Matrix Selector Switcher unit.
888.769.4156
5
FRONT PANEL
REAR PANEL
6
www.vanco1.com
Loading...