Vanco 4x3 HDBaseT, HDBT4X3 Technical Support

4x3 HDBaseT™
Matrix Selector

Switch

with Additional HDMI®

Output

Vanco Part Number:

HDBT4X3

Technical Support

www.vanco1.com • [e-mail] • 800-626-6445

www.vanco1.com

2

1. Do not expose this unit to water, moisture,
or excessive humidity.

2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.

3. To prevent risk of electrical shock or re
hazard, due to overheating, do not obstruct
unit’s ventilation openings.

4. Do not install near any source of heat,
including other units that may produce heat.

5. Do not place unit near ames.

6. Only clean unit with a dry cloth.

7. Unplug unit during lightening storms, or
when not used for an extended period
of time. A surge protector is strongly
recommended.

8. Protect the power cord from being walked
on or pinched, particularly at the plugs.

9. Use unit only with accessories specied by
the manufacturer.

10. Refer all servicing to qualied personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.

WARNING

DEAR CUSTOMER

Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before
connecting, operating or adjusting this product.
Please keep this manual for future reference.

This product is 100% inspected and tested in the United States
to verify HDMI performance parameters.

800-626-6445

3

FEATURES

HDBT4x3 is a professional HDBaseT Matrix Switcher that consist of the following inputs and outputs, 4 HDMI
IN (4kx2K@60Hz signal at max), 3 IR IN, 1 IR EYE, 4 IR OUT, 3 HDBaseT OUT, 1 HDMI OUT, 1 SPDIF OUT, 1
L&R RCA OUT, and TCP/IP, RS232 control port via phoenix connector. The HDBaseT Receiver is an HDBaseT
Receiver that consists of the following inputs and outputs, 1 HDBaseT IN, 1 IR IN, 1 IR OUT and HDMI OUT.
The receiver is powered directly by the Matrix Switcher. All HDMI inputs can be selected by either the front
panel buttons, IR, RS 232 or GUI. The selected source is delivered to HDBaseT zoned outputs 1~3 & HDMI
Output. The Matrix Switcher is capable of delivering 4K signals up to 40m, 1080p up to 70m and powering
the receivers via a single CAT5e cable. It is however recommended to use good quality CAT6 cable. This
Matrix Switcher also supports EDID management and is HDCP 2.2, 1.4 compliant. Audio sources can be
selected via RS232 commands and TCP/IP at the Matrix Switcher or by 3rd Party control.

4x3 HDBaseT™ Matrix Selector Switch with Additional
HDMI® Output

Part # HDBT4X3

• HDBaseT Matrix that features 3 HDBaseT outputs and 1 HDMI output

• Quick install kit includes 3 HDBaseT PoC receivers, 4 IR Emitter and Receiver sets and IR remote control

• Supports HDCP 2.2, and is backwards compatible with previous version of HDCP and HDMI

• Transmits 4Kx2K @ 60Hz 4:2:0 up to 26 ft (8m) via HDMI port and 131 ft (40m) via HDBaseT port

• 3 HDBaseT outputs with distances up to 230 ft (70m) at 1080p and 131 ft (40m) at 4Kx2K on a single

Cat5e/6 cable

• HDBaseTReceiversarepoweredbythematrixusingPoCtechnology•LEDindicatorsshowreal-time

switching status

• Controllableviafrontpanel,RS232,IRandTCP/IP•Supportsbi-directionalIR&RS232control

• Built-in GUI for TCP/IP control and setup

• Powerful EDID management

• Features Micro USB port for rmware upgrades

• Easy installation with rack-mounting design, mounting hardware included

• Power Supply : Matrix Unit, DC 24V; Receivers, PoC

• Matrix Dimensions: 14.2” W x 1” H x 5.9” D

• Receiver Dimensions: 2.4” W x .9” H x 4.7” D

• 4K HDBaseT Matrix Switcher

• (3) HDBaseT Receivers

• (4) IR Emitters (Optional)

• (3) IR Receivers (Optional)

• IR Receiver(Inserted into IR EYE port)

• IR remote

• RS232 cable (Phoenix to 9-pin D-Sub)

• Mounting ears & Screws

• (4) Trapezoidal Plastic pads (For 4K HDBaseT

Matrix Switcher)

• (12) Round Plastic pads (For HDBaseT
Receivers)

• Power Adapter (DC 24V 2.71A)

• Power Cord (Optional)

• Product Manual

PACKAGE CONTENTS

Please check the packaging and make sure the following items are contained in the shipping carton:

www.vanco1.com

4

Input ........................................................................ 4 HDMI

HDMI Standard .......................................................... Support HDMI1.4 & HDCP2.2 and is backward compatible with all previous

standards.

Output ...................................................................... 1 HDMI – 3 HDbaseT

Input and Output Level ................................................ T.M.D.S. 2.9V~3.3V

Input and Output Impedance........................................ 100Ω (Differential)

HDMI Standard .......................................................... Support HDMI1.4 & HDCP1.4 and is backward compatible with all previous

standards.

Video Signal .............................................................. HDMI (or DVI-D)

Transmission Distance ................................................ 1080P@60Hz ≤70m; 4Kx2K@60Hz ≤40m

Resolution Range ....................................................... Up to 4Kx2K@60Hz

EDID Management ..................................................... In-built EDID data and manual EDID management

Gain ......................................................................... 0 dB

Bandwidth ................................................................. 10.2Gbit/s

Switching Speed ........................................................ 200ns (Max.)

Output Signal ............................................................ Stereo audio, Digital audio

Analog Audio Output................................................... Support PCM

Digital Audio Output ................................................... Supports PCM, Dolby, DTS, DTS-HD

Frequency Response .................................................. 20Hz~20KHz

Output Connector ...................................................... 1 L&R(RCA) 1 SPDIF

Control Ports ............................................................ 4 IR OUT, 3 IR IN, 1 IR EYE, 1 TCP/IP (female RJ45), 1 RS232 (3-pin pluggable

terminal block)

Panel Control ............................................................. Front panel buttons

RS232 Control .......................................................... 3-pin pluggable terminal block

IR ............................................................................. Extended IR receiver

TCP/IP Control ........................................................... Web-based GUI

Power Supply............................................................. Input: 100-240V~, 50/60Hz; Output: DC 24V 2.71A

Power Consumption ................................................... 35W (Max)

Temperature.............................................................. 0~+50 Degrees C

Reference Humidity .................................................... 10% ~ 90%

Net weight ................................................................ 910g

HDBaseT Receiver:

Input ....................................................................... 1 HDBaseT; Female RJ45(with LED indicators);

Output ...................................................................... 1 HDMI; Female HDMI

Control ..................................................................... 1 IR IN, 1 IR OUT; 3.5mm mini jacks

Resolution Range ....................................................... Up to 4K×2K@60Hz

Transmission Distance ................................................ 1080P@60Hz ≤70m; 4Kx2K@60Hz ≤40m

Bandwidth ................................................................. 10.2Gbps

HDMI Standard .......................................................... Support HDMI1.4 and HDCP1.4

Temperature.............................................................. 0~ +50 Degrees C Humidity:10% ~ 90%

Power Supply............................................................. Powered by 4K HDBaseT Matrix Switcher.

Net Weight ............................................................... 280g

SPECIFICATIONS

800-626-6445

5

PANEL DESCRIPTIONS

1. Firmware: Micro USB port for updating rmware

2. Power Indicator: OFF: No power; RED: DC power present or Standby Mode

3. Input Selector Indicators: Total 4 groups, and each group is set up including 4 green indicators for 4 input
sources, numbered from “1” to “4”.

4. Output selector button: Total 4 output selector buttons, press the buttons to switch input cycle for the output.

5. HDMI Inputs: 4 x HDMI input ports, type A female HDMI connector, connect the Source with an HDMI cable to
any of the HDMI inputs.

6. IR In: 3 x IR IN: Connect with IR receiver, xed IR input for the output, cannot be switched separately. It makes up
an IR bi-directional transmission with the IR Out on the corresponding HDBaseT receiver.

7. IR Eye: Connect with extended IR receiver, use the IR remote to control the Matrix Switcher.

8. IR Out: (1-4) Plug in the IR Emitter and attach to the front of the Source. This then emits the IR signal received
from the HDBaseT Receiver. There are 4 IR Outputs sockets marked on IR matrix.

9. HDBaseT Output: The HDBT RJ45 outputs deliver HD video, Audio and PoC to the HDBaseT Receiver up to 70m.

10. HDMI Output: Connect an HDMI cable from the Matrix Switcher to the displayer.

11. SPDIF Output: Digital audio output connects directly via an optic bre cable to the Toslink input on a sound bar.

12. RCA (L&R) Output: PCM Analogue audio output sockets connect the de-embedded audio additional speakers.

13. Control : TCP/IP: RJ45 port. Connect with PC for Web-based GUI control. RS232: Serial port for unit control,
3-pin pluggable terminal block, connects with control device (e.g. PC).

14. DC 24V: Connect with DC24V 2.71A power adaptor

4

1

2

3

8

5

6

7

9

10 11 12

13

14

1. HDMI Out: Connect to HDMI display.

2. IR In: Plug in the IR receiver, this will receive the IR signals from the RCU and send through to the Matrix
Switcher and then control the desired source.

3. IR Out: Plug in the IR emitter and attached to the fornt of the display, this will send the IR signals form the Matrix
Switcher to control the display which is connected to the HDMI OUT port.

4. Power Indicator: OFF: No power; RED: DC power present (PoC).

5. TP In: The RJ45 socket has two LED status indicators. Plug in the Pre-installed CAT cable in to the HDBT RJ45
socket. HDCP LED indicator: OFF: No HDMI trafc (no picture) GREEN: Signals with HDCP, Blinking GREEN:
Signal without HDCP. LINK/HDBT Link status indicator: OFF: No Link, YELLOW: Link Successful, Blinking
YELLOW: Link Error

4

1

2 3

5

www.vanco1.com

6

CONNECT AND OPERATE

1. Connect HDMI sources (e.g. DVD) to HDMI input ports of the Matrix Switcher via good quality HDMI
cables.

2. Connect the Pre-Installed CAT5e/CAT 6 cable infrastructure to Matrix Switcher and HDBaseT receivers via
good quality patch leads.

3. Connect HDTV to HDMI output port via HDMI cable.

4. Plug in an HDMI cable in to each of HDBaseT Receiver and connect to the local display [HDTV].

5. Connect AVR amplier to SPDIF output port or via the Toslink optic bre cable.

6. Connect speaker to L&R (RCA) output port via audio cable.

7. Plug the IR Receivers 3.5mm jack into the IR IN sockets on HDBaseT Receivers and plug in the IR
Emitters to the IR OUT sockets (1~4) on Matrix Switcher to make up as IR Matrix.

8. Plug the phoenix connector in to the RS232 socket on the matrix, this will enable the Matrix Switcher to
be controlled via a PC.

9. Plug in a Patch lead from the router in to the Ethernet port on Matrix Switcher to control Matrix Switcher
by TCP/IP protocol.

10. Plug in the Power supply adapter 24V DC and tighten to secure. Once all components have been
connected and the installation is completed, switch on the mains supply at the socket.

NOTE:

• Connect HDBT ports of Matrix Switcher and far-end HDBaseT Receiver with straight-through cable.

• IR receivers connected to IR IN should be with carrier. If not, send command %0900. or %0901.to

activate native carrier mode or force carrier mode in the IR matrix launched between Matrix Switcher
and far-end HDBaseT Receiver.