Vanco Evolution EVEXKVM1, Evolution EVEXKVM1-TX, Evolution EVEXKVM1-RX Installation Manual
Vanco Part Number
EVEXKVM1
HDMI® Extender
with KVM
www.vanco1.com • 800.626.6445
HDMI® EXTENDER
W I T H K V M
www.vanco1.com
2
1. Do not expose this unit to water, moisture, or
excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms or when
not used for an extended period of time. A
surge protector is strongly recommended.
8. Protect the power cord from being walked on
or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
This product is 100% inspected and tested in the United States to verify
HDMI performance parameters.
800.626.6445
3
INTRODUCTION
The Evolution by Vanco EVEXKVM1 HDMI Extender over Single Cat5e/6 with KVM, auto EDID/EQ, and PoE extends high
denition video and audio signals, KVM (Keyboard, Video, Mouse) signals, and power at a distance of up to 164ft/50m
over a single Cat5e/6 cable. KVM capability using USB 2.0 allows for controlling a security NVR/DVR, computer, NAS
system, or any other component that is controlled by USB with this extender. No need to run a separate line or extender
just for KVM control! Also features Power over Ethernet (PoE) Technology, which transmits power over Cat5e/6, allowing
either the Transmitter or Receiver to be powered without the use of a power supply. No EDID or EQ adjustments are
necessary as the units automatically adjust for compatibility and gain. This product fully supports DTS-HD and Dolby
TrueHD audio formats, and is HDCP compliant. For extending HDMI over a single Cat5e/6 with KVM at a long distance,
with Power over Ethernet, the EVEXKVM1 is a great plug and play solution for any device that needs to be extended and
controlled with a keyboard and mouse!
The EVEXKVM1 includes two units: transmitting unit (EVEXKVM1-TX) and receiving unit (EVEXKVM1-RX). The transmitting
unit is used to capture the HDMI input with KVM signals and carries the signals via one cost effective Cat5e/6 cable. The
receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing KVM signals. The EVEXKVM1
offers the most convenient solution for HDMI extension over a single Cat5e/6 with Power over Ethernet, and is the perfect
solution for any application.
FEATURES
HDMI® Extender with KVM
Part # EVEXKVM1
• Transmits audio and video via HDMI as well as complete KVM (Keyboard, Video, Mouse) functionality via
USB 2.0 ports over a single Cat5e/6 up to 164ft/50m with POE.
• Power Over Ethernet (PoE), integrates power into the Cat5e/6 cable, requiring no power supply for either
the Transmitting unit or Receiving unit (opposite of unit that is plugged in to power)
• Auto EDID management automatically adjusts to overcome compatibility issues
• Auto EQ distance for perfect transmission and reception of HDMI signals
• Supports up to 1920x1080 @ 60Hz resolutions
• Transmission Range: Extends HDMI signals up to 164ft/50m over a single Cat5e or Cat6 cable
• Extends USB 2.0 high speed at 480Mbps to 164ft/50m
• RX unit provides 4 USB 2.0 high speed ports at display end
• USB ports allow for charging of connected USB devices (please use properly certied and licensed
cabling with utilizing the charging feature)
• RX integrated with Hi-Fi USB audio card, supports analog passive earphone and microphone access
• VESA DDC and hot swap technology (HPD)
• Compatible HDMI 1.3/DVI 1.0
• HDCP 1.4
• Dimensions: 3.25” W x .8” H x 3.6” D
www.vanco1.com
4
SPECIFICATIONS
Transmitters ............................................................. HDMI input, USB to host (Type B),RJ45 Ethernet
interface, 12V DC in
Receivers ................................................................. HDMI output, 4 USB to device (Type A), RJ45
Ethernet interface, 3.5mm audio/MIC out,12V DC in
Power ...................................................................... <2W TX or <3W RX (not including external USB
device power consumption)
POE ......................................................................... 12V 2A DC adapter, either at transmitter or
receiverr
Dimension ................................................................ 3.7” W x 3.5” H x .8” D
Net weight ............................................................... 389g for TX and RX
Video Bandwidth ....................................................... Maximum TMDS clock frequency 165MHz, 4.95Gbps
TMDS input signal ..................................................... 1.2 volts (point to point)
DDC input signal ....................................................... 5 volts (point to point)
Resolution and Distance ............................................. 1920x1080 up to 170ft/50m CAT5e
USB 2.0 Standard ..................................................... High speed 480Mbps, full speed and low speed
Audio Card ............................................................... Integrated USB 2.0 plug and play stereo audio card,
windows self-driver
Indicator ................................................................. Power-Green,Video Link-Yellow, USB Link- Yellow
ESD level ................................................................. HBM ±4 kV (Contact Discharge)
Temperature range ................................................... 0 ~ 40°C (operation), -20~60°C(stock)
Compliance .............................................................. FCC; CE; RoHS
PACKAGE CONTENTS
• EVEXKVM1 (TX & RX)
• USB Type A to Type B cable
• (1) DC 12V/2A power supply
• Product Manual
Loading...