Vanco Evolution EVO-IP, EVOIPCTL1, EVOIPTX1, EVOIPRX1 Quick Start Manual
Vanco Part Numbers:
EVOIPTX1 Transmitter
EVOIPRX1 Receiver
EVOIPCTL1 Control Box
www.vanco1.com • 800.626.6445
Quick Start Guide
EVO-IP HDMI®
OVER IP
www.vanco1.com
2
1. Do not expose this unit to water, moisture, or
excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms or when
not used for an extended period of time. A
surge protector is strongly recommended.
8. Protect the power cord from being walked on
or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
This product is 100% inspected and tested in the United States to verify
HDMI performance parameters.
800.626.6445
3
INTRODUCTION
FEATURES
HDMI® over IP
• Supports 4K@60Hz, 4:4:4 chroma
• System can support over 1000 transmitters and 1000 receivers
• HDR10 and Dolby Vision compatible
• Dolby/DTS/PCM audio formats supported
• HDCP 2.2/1.4
• POE or can be powered using provided power supply
• Manual dip switch congurable for a truly IP-Less installation
• Easy GUI automatically detects new devices in the system
• Customizable labels and names of sources and displays
• Setup through the GUI can be done without a computer even being on site
• Analog and Digital audio breakouts on TX and RX
• HDMI Loop-out on TX for cascading or monitoring
• Upscale to 4K@30Hz or downscale to 720p
• EDID preset/learning
• Video Wall mode supports up to 5x5 conguration
• OSD mode to display text, pictures, or logos on the screen (great for digital signage)
• Connects to the cloud to schedule events or to troubleshoot a situation remotely (opportunity for
recurring revenue)
• iOS and Android end user app makes it easy to control switching within the system
• Able to be controlled with Alexa enabled products
The Evolution by Vanco EVO-IP HDMI over IP is a complete audio, video, and control product over ethernet system. As a whole,
the system has the ability to send up to 1064 sources to 1064 displays along with IR and RS-232 pass-through, analog and
digital audio breakouts on the send and receive ends, video up to 4K@60Hz and HDR10/Dolby Vision compatibility, with POE
up to 330ft/100m when connected to a POE enabled switch off of a single Cat6 cable. The transmitter is also equipped with
an HDMI loop-out that allows the system to incorporate other products such as Evolution tiling and Multi-view products easily
with minimal additional programming. As a dedicated system, EVO-IP can also create and recall video walls using up to 25
displays, and can overlay text, pictures, and even albums which is perfect for digital signage! When connected to a network,
the EVO-IP Cloud allows for additional features such as scheduling events or maintenance, remote monitoring of a system
including diagnostics and troubleshooting, as well as voice control capabilities with Alexa enabled products! With an IP-less
installation option as well as any new sources/displays being discovered automatically within the system, the EVO-IP HDMI
over IP system is the fast, easy, and perfect solution for both residential and commercial installations.
www.vanco1.com
4
SPECIFICATIONS
TECHNICAL SPECS - Transmitter and Receiver
HDMI Compliance ...................................................... HDMI
HDCP Compliance ...................................................... Yes
Video Resolution ........................................................ 4K@60Hz, 4:4:4; 4K@60Hz, 4:2:0 HDR10;
4K@30Hz, 4:4:4 HDR10; 4K@30Hz, 4:2:2 HDR10 and Dolby Vision; 4K@24Hz, 4:4:4 HDR10 and Dolby
Vision
Latency ..................................................................... 2 frames (33ms) maximum
HDMI over UTP transmission [24-bit] .......................... 1Ultra HD (4K@60) up to 330ft/100m over Cat6
Audio Support ........................................................... Surround sound (up to 7.1ch) PCM, DTS, Dolby
Input TMDS signal ...................................................... 1.2 Volts [peak-to-peak]
Input DDC signal ........................................................ 5 Volts [peak-to-peak, TTL]
ESD Protection .......................................................... Human body model — ±15kV [air-gap discharge] &
±8kV [contact discharge]
IR Pass-Thru ............................................................. Full-duplex bi-directional
RS-232 Support ........................................................ Yes
IR Remote Control .................................................... Dual Band: 20-60kHz
HDMI Connector ........................................................ Type A [19-pin female]
MECHANICAL SPECS - Transmitter and Receiver
Housing .................................................................... Metal enclosure
Dimensions ...............................................................
Weight .....................................................................
Fixedness .................................................................. Wall-mounting case with screws
Power supply ............................................................. 5V 2A DC
Power consumption .................................................... 6 Watts TX; 5Watts RX
Operation temperature ............................................... 32~113F
Storage temperature.................................................. -4~140F
Relative humidity ....................................................... 20-90% RH (no condensation)
Loading...