Vanco Part Numbers:
EVOIPTX1 Transmitter
EVOIPRX1 Receiver
EVOIPCTL1 Control Box
www.vanco1.com • 800.626.6445
Quick Start Guide
EVO-IP HDMI®
OVER IP
www.vanco1.com
2
1. Do not expose this unit to water, moisture, or
excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms or when
not used for an extended period of time. A
surge protector is strongly recommended.
8. Protect the power cord from being walked on
or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
This product is 100% inspected and tested in the United States to verify
HDMI performance parameters.
800.626.6445
3
INTRODUCTION
FEATURES
HDMI® over IP
• Supports 4K@60Hz, 4:4:4 chroma
• System can support over 1000 transmitters and 1000 receivers
• HDR10 and Dolby Vision compatible
• Dolby/DTS/PCM audio formats supported
• HDCP 2.2/1.4
• POE or can be powered using provided power supply
• Manual dip switch congurable for a truly IP-Less installation
• Easy GUI automatically detects new devices in the system
• Customizable labels and names of sources and displays
• Setup through the GUI can be done without a computer even being on site
• Analog and Digital audio breakouts on TX and RX
• HDMI Loop-out on TX for cascading or monitoring
• Upscale to 4K@30Hz or downscale to 720p
• EDID preset/learning
• Video Wall mode supports up to 5x5 conguration
• OSD mode to display text, pictures, or logos on the screen (great for digital signage)
• Connects to the cloud to schedule events or to troubleshoot a situation remotely (opportunity for
recurring revenue)
• iOS and Android end user app makes it easy to control switching within the system
• Able to be controlled with Alexa enabled products
The Evolution by Vanco EVO-IP HDMI over IP is a complete audio, video, and control product over ethernet system. As a whole,
the system has the ability to send up to 1064 sources to 1064 displays along with IR and RS-232 pass-through, analog and
digital audio breakouts on the send and receive ends, video up to 4K@60Hz and HDR10/Dolby Vision compatibility, with POE
up to 330ft/100m when connected to a POE enabled switch off of a single Cat6 cable. The transmitter is also equipped with
an HDMI loop-out that allows the system to incorporate other products such as Evolution tiling and Multi-view products easily
with minimal additional programming. As a dedicated system, EVO-IP can also create and recall video walls using up to 25
displays, and can overlay text, pictures, and even albums which is perfect for digital signage! When connected to a network,
the EVO-IP Cloud allows for additional features such as scheduling events or maintenance, remote monitoring of a system
including diagnostics and troubleshooting, as well as voice control capabilities with Alexa enabled products! With an IP-less
installation option as well as any new sources/displays being discovered automatically within the system, the EVO-IP HDMI
over IP system is the fast, easy, and perfect solution for both residential and commercial installations.
www.vanco1.com
4
SPECIFICATIONS
TECHNICAL SPECS - Transmitter and Receiver
HDMI Compliance ...................................................... HDMI
HDCP Compliance ...................................................... Yes
Video Resolution ........................................................ 4K@60Hz, 4:4:4; 4K@60Hz, 4:2:0 HDR10;
4K@30Hz, 4:4:4 HDR10; 4K@30Hz, 4:2:2 HDR10 and Dolby Vision; 4K@24Hz, 4:4:4 HDR10 and Dolby
Vision
Latency ..................................................................... 2 frames (33ms) maximum
HDMI over UTP transmission [24-bit] .......................... 1Ultra HD (4K@60) up to 330ft/100m over Cat6
Audio Support ........................................................... Surround sound (up to 7.1ch) PCM, DTS, Dolby
Input TMDS signal ...................................................... 1.2 Volts [peak-to-peak]
Input DDC signal ........................................................ 5 Volts [peak-to-peak, TTL]
ESD Protection .......................................................... Human body model — ±15kV [air-gap discharge] &
±8kV [contact discharge]
IR Pass-Thru ............................................................. Full-duplex bi-directional
RS-232 Support ........................................................ Yes
IR Remote Control .................................................... Dual Band: 20-60kHz
HDMI Connector ........................................................ Type A [19-pin female]
MECHANICAL SPECS - Transmitter and Receiver
Housing .................................................................... Metal enclosure
Dimensions ...............................................................
Weight .....................................................................
Fixedness .................................................................. Wall-mounting case with screws
Power supply ............................................................. 5V 2A DC
Power consumption .................................................... 6 Watts TX; 5Watts RX
Operation temperature ............................................... 32~113F
Storage temperature.................................................. -4~140F
Relative humidity ....................................................... 20-90% RH (no condensation)
800.626.6445
5
PACKAGE CONTENTS
• EVOIPTX1, EVOIPRX1, OR EVOIPCTL1 unit (each sold separately)
• IR Transmitter (with EVOIPTX1 and EVOIPRX1)
• IR Receiver (with EVOIPTX1 and EVOIPRX1)
• 5V Power Supply (optional, can be used as a redundant power with use of a POE switch)
• Set of mounting ears/screws
• Product Manual
SPECIFICATIONS
TECHNICAL SPECS - Control Box
Role of Usage ............................................................ Smart Controller
Input ........................................................................ 1 x RJ-45
Output ...................................................................... 1 X HDMI
HDMI Connector ........................................................ Type A [19-pin female]
RJ-45 Connector ....................................................... WE/SS 8P8C
USB (Female) ............................................................ Reserved for future use
MECHANICAL SPECS - Control Box
Housing .................................................................... Metal enclosure
Dimensions ............................................................... 90 x 65 x 29mm [3.5” x 2.5” x 1.1”]
Weight .....................................................................
Fixedness .................................................................. Rack-mount with ears
Power supply ............................................................. 5V DC
Power consumption .................................................... 3.5 Watts [max]
Operation temperature ............................................... 32~113F
Storage temperature.................................................. -4~140F
Relative humidity ....................................................... 20-90% RH (no condensation)
www.vanco1.com
6
1. Link Indicator Light (lights up when connected and transmitting signal to ethernet switch)
2. Power Indicator Light (lights up when powered up by PoE or included power supply)
3. Info Indicator Light (shows data is being sent/received over the Cat cable/RJ45 port)
4. DB9 connector for RS-232 Control Pass-Through
5. IR-TX port (connect included IR Transmitter cable for source control)
6. IR-RX port (connect included IR Receiver cable for display control)
7. Unit ID dip switches (disables browser based GUI for setting up and addressing units for IP-less setup)
8. RJ45 port (connect to ethernet switch)
9. HDMI Loop-out for cascading HDMI signal into other devices or to split out to additional display
10. HDMI IN (connect to a source)
11. Toslink Out (de-embeds/extracts digital audio from HDMI source using Toslink adapter)
12. Stereo Out (de-embeds/extracts analog audio from HDMI source using a stereo 3.5mm connector)
13. 5V Power Port (optional, connect included power supply if using a non-PoE ethernet switch or to use for
redundant power)
PANEL DESCRIPTIONS
Transmitting Unit
1
2 3
4
5 6
7
8
9
10
11 12
13
800.626.6445
7
Receiving Unit
PANEL DESCRIPTIONS
1. Link Indicator Light (lights up when connected and receiving signal from ethernet switch)
2. Power Indicator Light (lights up when powered up by PoE or included power supply)
3. Info Indicator Light (shows data is being sent/received over the Cat cable/RJ45 port)
4. DB9 connector for RS-232 Control Pass-Through
5. IR-TX port (connect included IR Transmitter cable for source control)
6. IR-RX port (connect included IR Receiver cable for display control)
7. Unit ID dip switches (disables browser based GUI for setting up and addressing units for IP-less setup)
8. RJ45 port (connect to ethernet switch)
9. HDMI OUT (connect to a display)
10. Toslink Out (de-embeds/extracts digital audio from HDMI source using Toslink adapter)
11. Stereo Out (de-embeds/extracts analog audio from HDMI source using a stereo 3.5mm connector)
12. 5V Power Port (optional, connect included power supply if using a non-PoE ethernet switch or to use for
redundant power)
1
2
3
4
5 6
7
8
9
10 11
12
www.vanco1.com
8
CONNECTION DIAGRAM
Control Box
PANEL DESCRIPTIONS
1. 5V Power Port (necessary as this unit requires external power)
2. Status Indicator Light (lights up when communicating with the system)
3. Power Indicator Light (lights up when powered up by included power supply)
4. HDMI OUT (connect to local display to show system IP information)
5. RJ45 port (connect to ethernet switch)
6. USB ports (reserved for future use)
1
2 3
4
5
6
800.626.6445
9
CONNECT AND OPERATE
Before connecting and setting up the EVO-IP System, please enable settings within your ethernet switch that
will allow you get the best performance possible. For additional information on which ethernet switches are
compatible, please visit the product page at www.vanco1.com.
For best results, ensure your ethernet switch has IGMP Snooping, Jumbo Frames, and POE enabled.
1. Connect the EVOIPTX1 and EVOIPRX1 transmitters and receivers to the network switch with a well
terminated Cat5e/6. Ensure there is 1 transmitter being used for every source/input and 1 receiver
being used for every display/output in the system. Note: Vanco recommends using Cat6 for any 4K
applications and to use one of the ethernet switches recommended on the product webpage
found at www.vanco1.com.
2. Connect the EVOIPCTL1 to the same network switch. Note: The EVO-IP System is automatically setup
to DHCP network settings. To set up any EVO-IP device for a static IP, please refer to the Setup
and Features Manual.
3. Connect the HDMI output of the EVOIPCTL1 to a local display. This will provide you with the necessary
network information to continue the setup.
4. Connect power to the EVOIPCTL1 and turn on the ethernet switch. If your ethernet switch is not capable
of POE (power over ethernet), connect the provided 5v power supplies to each EVOIPTX1 and EVOIPRX1
5. Using a computer that is connected to the same network, type in www.evo-ip.local into a web browser to
get to the GUI. You can also enter the GUI by typing the IP Address shown on the display connected to
the HDMI output of the EVOIPCTL1, or by scanning the QR code found on the same screen using a phone,
tablet, or computer connected to the same network
www.vanco1.com
10
6. Type in the username and password for the system
Installer: Username and password is admin (full access to settings)
User: Username and password is user (limited access to settings)
7. Go to the SETUP tab to further customize the name and ID for each device
800.626.6445
11
LIMITED WARRANTY
With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment
it manufactures or sells will be free from defects in materials and workmanship for a period of two years from
the date of purchase. Should this product, in Vanco’s opinion, prove defective within this warranty period,
Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become
the property of Vanco. This warranty does not apply to those products which have been damaged due to
accident, unauthorized alterations, improper repair, modications, inadequate maintenance and care, or use in
any manner for which the product was not originally intended.
Items integrated into Vanco products that are made by other manufacturers, notably computer hard
drives and liquid crystal display panels, are limited to the term of the warranty offered by the respective
manufacturers. Such specic warranties are available upon request to Vanco. A surge protector, power
conditioner unit, or an uninterruptible power supply must be installed in the electrical circuit to protect against
power surges.
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales
invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco
regarding warranty repair or replacement.
TECHNICAL SUPPORT
In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email
technical support issues to techsupport@vanco1.com.
When calling, please have the Model Number, Serial Number (afxed to the bottom of the unit) and Invoice
available for reference during the call.
Please read this Instruction Manual prior to calling or installing this unit, since it will familiarize you with the
capabilities of this product and its proper installation.
All active electronic products are 100% inspected and tested to insure highest product quality and troublefree installation and operation. The testing process utilizes the types of high-denition sources and displays
typically installed for entertainment and home theater applications.
For additional information, such as helpful installation videos, etc. please visit www.vanco1.com
LIABILITY STATEMENT
Every effort has been made to ensure that this product is free of defects. The manufacturer of this product
cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising
from its use. It is the responsibility of the user and installer of the hardware to check that it is suitable for
their requirements and that it is installed correctly. All rights are reserved. No parts of this manual may be
reproduced or transmitted by any form or means electronic or mechanical, including photocopying, recording
or by any information storage or retrieval system without the written consent of the publisher.
Manufacturer reserves the right to revise any of its hardware and software following its policy to modify and/or
improve its products where necessary or desirable. This statement does not affect the legal rights of the user
in any way.
Vanco® International
506 Kingsland Drive
Batavia, Illinois 60510
call: 800.626.6445
fax: 630.879.9189
visit: www.vanco1.com
Loading...