Hardware Kit:
Hardware Kit:
10
Part 3-Mounting the flat panel screen and installing locking bar
Part 3-Mounting the flat panel screen and installing locking bar
7
5
2
1
8
9
Hook the top of brackets onto the top flange of wall plate(1). Then swing
the screen down. Through the top of the bracket to the bottom of it with
the Safety plate . Secure with padlocks(6).(5)
4
NOTE: Always use an assistant or mechanical lifting equipment to safely lift
NOTE:
and position heavy equipment.
3
5
ID
4
7
8
10
A
B
6
A-H
Wall
JM
K
LI
Wall
5
6
1
3,4
ID
Qty
1
1
2
1
3
1
1
2
5
6
2
1
1
9
1
3
4
4
Description
Wall plate
Cantilever arm
Left bracket
Right bracket
Safety Plate
Padlock
6x6 Wrench
5x5 Wrench
4x4 Wrench
Cord management wrap
M4 mm×12 bolt
M4 mm×16 bolt
Qty
4
C
4
D
4
E
4
F
4
G
4
H
4
I
6
J
6
K
L
6
4
M
Description
M5× mm16 bolt
M6× mm16 bolt
M8×16mm bolt
M5×36mm bolt
M6×36mm bolt
M ×36mm8 bolt
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer
-2-
-7-
Part 2b-Attaching brackets to screen with recessed back
Part 2b-Attaching brackets to screen with recessed back
Part 1a-Wood Stud Mounting
Part 1a-Wood Stud Mounting
Center brackets vertically on back of screen. Select the medium(F),large(G)
or extra large(H) screws. Attach brackets to screen using four selected
screws, four square washers(I) and four spacers(M) at the top and bottom of
each bracket. Tighten screws firmly. Do not overtighten.
Square washer(I)
Large hole for
M6 screws
Medium hole
forM5screws
Extra Large hole
forM8screws
M
I
F-H
Usewallplate(1)asatemplate,makesureitislevel,andmarksixmounting
holes along the center lines of the wood studs. Drill six 3/16
””(5mm)dia
.
holes 2 (50mm) deep. Level wall plate(1) and attach to wall with six long
)) . .
bolts(J and six washers(L . Tighten screws firmly Do not overtighten
2 50mm)”(
Φ3/16 (5mm)”
Wood stud
L
J
-6-
-3-
Part 1b-Concrete Wall Mounting
Part 1b-Concrete Wall Mounting
Part 2a-Attaching Brackets To Screen With Flat Back
Part 2a-Attaching Brackets To Screen With Flat Back
Level wall plate(1) and use wall as a template to mark six holes. Drill six 3/8
(10mm) dia. holes 2 (50mm) deep. Insert six anchors(K) into holes and
”
secure wall plate with six long bolts(J) and six washers(L).Tighten screws
firmly. Do not overtighten
.
2(” 50mm)
Φ3/8 (10mm)”
Concrete Wall
K
”
Center brackets vertically on back of screen. Select the small(A or B),
medium(C),large(D) or extra large(E) screws. Attach brackets to screen
using four selected screws and four square washers(I) at the top and bottom
of each bracket. Tighten screws firmly. Do not overtighten
.
Square washer(I)
Large hole for
M6 screws
Medium hole
forM5screws
Small hole for
M4 screws
Extra Large hole
forM8screws
I
A-E
-4-
L
J
-5-
Loading...