VANATOO® TRANSPARENT ONE ENCORE
™
POWERED SPEAKERS
™
Quick Start Guide
Unpack Your System
1
1) Active speaker
2) Passive speaker
3) 2 Grills
4) IR remote control
5) Optional isolation feet
6) USB A to USB B cable
Connect the Speakers
2
The included speaker interconnect cable with screw-on collar
connectors makes this quick and easy.
Connect Power
3
7) 3.5 mm to 3.5 mm cable
8) Four conductor
speaker wire
9) 3.5 mm to RCA “Y” cable
10) Quick Start Guide and a
Safety Sheet
1
4
5
2
6
7
3
98
1. Make sure the power switch (2) is in the OFF position.
2. Plug the AC power cord into the power outlet.
Connect Your Audio Source
4
Turn the volume controls on the speaker (1) and on the audio
source both to minimum.
1. Analog (3) — Connect your source using the included
using 3.5mm to 3.5mm cable or 3.5mm to RCA cable as
appropriate for your source component.
2. Digital Coax (4) — Connect your source component using
a 75 ohm digital coaxial RCA cable.
3. Optical (5) — Connect your source component to the
Vanatoo T1E using a Toslink optical cable.
4. USB (6) — Connect your computer to the T1E using the
supplied USB A to USB B cable. Select the Vanatoo T1E
in your computer’s audio settings.
5. Bluetooth —
a. Press and release the “Pair-Prog” button (7) on the
b. Ensure Bluetooth is turned-on on your source
c. Ensure your source device is connected to the
rear of the active speaker, or press “Enable” and
then “BT Pair” on the remote control.
device and pair with the Vanatoo T1E.
Vanatoo T1E over Bluetooth and play music!
1
PAIR-PROG
3
7
8
9
SERVICE
TURN OVER
2
4
5
6
Designate Left-Right speaker
5
Set the Left–Right switch (9) to designate whether the active
speaker is located to your right or left (as you face the speakers).
This ensures the music is recreated as it was recorded.
Install the Grills
6
Grills come in individual plastic bags. Simple magnetic mounting (no or little alignment
necessary). Can go either way such that the “Vanatoo” logo is upright on the bottom.
Listen to Music!
7
Turn the power switch to the ON position (2). The blue LED (9) will light up within
5 seconds to indicate power to the unit. In most applications you can set the T1E
volume control to 100% and adjust the volume up/down from your source (Computer,
Bluetooth device, etc).
Remote Control
8
The included IR Remote Control is especially handy when your T1E’s are used with a
TV, or for switching sources, adjusting bass and treble, etc. Note that you must hit the
“Enable” button to enable the other buttons inside the rectangular box for 15 seconds.
Optional Settings
9
The T1E has a lot of setup options, such as enabling the speakers to play mono,
disabling sleep mode, varying the LED brightness, connecting a subwoofer and
alternate bass proles for room placement. Go to www.vanatoo.com/support/
downloads to download the user manual for a full description of the T1E and its
setup options.
CONGRATULATIONS!! That’s it! We hope you enjoy your
Vanatoo Transparent One Encore powered speakers.
For additional setup up information, connectivity options, and the troubleshooting
guide, check out the Transparent One Encore Owner’s Guide or visit us at www.
vanatoo.com.
Contact Us
Email: support@vanatoo.com
“Vanatoo” is a registered trademark, “Vanatoo Technology Serving Art” logo and “Transparent One Encore” are trademarks of Vanatoo LLC
Copyright 2018 Vanatoo LLC, all rights reserved
Loading...