Ceiling heater
user guide
Certified
Made in Russia
.2010
АВ41
quick fixing
doesn t require
any service
enveronmentally
friendly isolation
one “ПИОН”
is worth two
convectors
record low energy
consumption
up to 50% economy
increased efficiency
quotient emission
double resource
of the heating
element
ATTENTION
before using the heater read this manual
!!!
.
CONTENTS
page .
Introduction
Technical data
Heater details
Delivery complectation
Safety measures
Installation
Electrical connection
Start
Exploitation and technical supply
Possible disfunctions
Storage
Guarantee
Guarantee obligations
Reception certificate
Sales certificate
1. 1
2. 2
3. 3
4. 3
5. 4
6. 5
7. 7
8. 8
9. 11
10. 11
11. 11
12. 13
13. 14
14. 15
15. 15
1.Introduction
Thank you for buying new Infrared Ceiling Heater “ПИОН” !
Infrared heaters occupy a special place among heaters meant for ensuring comfortable
atmosphere
Infrared heaters are presently recognized as the best energy- saving electrical devices.
Energy is economised by transmitting warmth via infrared rays. The heater is installed on the ceiling,
the transmitting plate faces the floor and heats up to 25 C. It spreads warm rays at the angle 0f 120 C.
This way of transmitting warmth ensures 93% energy accumulation by objects, surfaces and walls
while only 7% is dissolved in the air. The temperature
Dear customer !
1
in dwellings and industrial premises. They are economical, environmentally
friendly, long-lasting and reliable. They have modern design, do not occupy much space,
and safe.
is balanced according to the height , the
floor is warmer than the air above.
Warm surfaces accumulate warmth and, in their turn, heat the air. It offers a number of
advantages as compared to other heating devices; the square of warm surfaces is larger,
there are no air-dust currents, the
promises cool slower , no energy is lost to heat air under
the ceiling, the air doesn t get too dry. These peculiarities ensure energy saving and make
the heater the most comfortable and the safest device.
“ПИОН”
“ПИОН”
;
;
infrared heater are new improved models. Now they are elegant and more solid
due to alluminium alloy. They are covered by powder enamels and have different colours,
small size, new forms of fixing and original wide angle emission plate.
All these features make infrared heater the first of the best.
Besides, there is a possibility to build up heating systems of different power with the help
of special frames to combine heaters with acoustic and lightening devices into entire
group which looks perfect in modern interiors of any premises dwellings , offices , shops,
stores, etc.
are mobile
2. .Technical data
2
Technical data are given in the table:
Model
Power W ( )
Power W ( )
Power W ( )
Power W ( )
Voltage V ( )
Voltage V ( )
Voltage V ( )
Voltage V ( )
Curr.
(А)
Curr.
(А)
Curr.
(А)
Curr.
(А)
2,7
4,6
ПИОН 06
ПИОН 04
ПИОН 10
ПИОН 13
ЭЛ 20R
ЭЛ 30R
ЭЛ 40R
1005х125х55
1515х125х55
Size
(мм)
Size
(мм)
Size
(мм)
Size
(мм)
780х125х551,8 4/82
2,8
4,2
4,26
6/12
10/20
13/26
Weight
g(к )
Weight
g(к )
Weight
g(к )
Weight
g(к )
Heated area
sq. ( м )
Heated area
sq. ( м )
Heated area
sq. ( м )
Heated area
sq. ( м )
2
1715х125х55
220\230
4 04
6 06
220\230
1 001 220\230
1 004
220\230
2000
3000
4000
220
220/380
220/380
9,2
4,6
6,1
1500х285х53
11
19
19
1500х415х53
1500х415х53
20/40*
30/60*
40/80*
квадро 05
500 220
2,5
600х600х35
5/10
3,9
2
2
2
2
ПИОН group
Quandro group
4,6
6,8
ИКО-1.0
ИКО-0.5
ИКО-1.5
ИКО-2.0
1245х112х75
1678х112х75
795х90х752,5
5/10*
2,2
3,1
4,3
5,49,1
10/20*
15/30*
20/40*
2176х112х75
220500
1000 220
1500 220
2000
220
13,6
11,8
ИКО-3.0
ИКО-4.5
ИКО-6.0
1674х212х75
1674х312х75
6,3
9,5
10,2
15,8
30/60*
45/90*
60/120
2182х260х70
3000
220/380
4500
220/380
6000
220/380
Industrial group
Open heating element group
* requires technical account
*
Model
Model
Model
Model
3. “ПИОН” . heater details
1. .
2. .
3. .
4. .
5. .
6. .
7.
Frame
Installation element
Low temperature heating element
Heat-emitting plate
Ceramic isolator
Power indication lamp
Frame plate.
4.Delivery complectation
1. “ПИОН”
2.
3.
4.
Heater
Installations details
Package
User manual
1
2
3
4
5
6
7
3
4
5.Safety measures
2.5
8.5
9.5
10.5
11.5
12.5 220/230
13.5
14.5
15.5
16.5
7.5
18.5
19.5
20.5
Use heater only for its purpose.
Install the heater as said in chapter 6 and 7.
The heater can be used to warm up dwellings and industrial premises, but for those prone
to explosions (A, B categories)
The heater is permitted in wet premises under the condition water does not get
on its surface.
Do not dip the heater into water or other liquids.
Do not touch the heater until it is cool.
The power flex must not touch hot heater surfaces.
Heater exploitation is not recommended without earth connection (Chapter 7),
electrical protection against high voltage and short circuit current is desirable.
Electrical connection is recommended to be fulfilled by qualified specialists (Chapter 7).
Connect the heater only to the source of alternating current with voltage V.
Combined exploitation of the heater together with programming devices or timer
which turns on the heater automatically even if it is covered or incorrectly installed
is forbidden (Chapter 6).
Heater connection to the power point should use a flex and a plug.
Use brass wire not less than 2,5 sq. mm., in diameter for connection.
1 It is forbidden to hang any objects on a heater, or cover it.
After installing the heater check its reliability attaching the weight of 12 kg.,
to the centre.
Do not repair the device yourself ! It should be done by the service centre specialists
only.
To repair the heater only original spare parts can be used.
3.5
4.5
5.5
6.5
7.5
!
!
Strongly prohibited to make any changes in the heater construction
Any changes will cancel guarantee
If you connect the heater in a wrong way you lose your guarantee service !
1.5 !
Strongly prohibited to touch the surface of working heater to avoid burns
6.Installation
1.
2. “ПИОН”)
3.
“ПИОН”)
4.
Take the heater out of the package and put it on a horizontal surface heater plate down.
Define the place for the heater and mark the point of the screw ring (for or corner
fittings according to the scheme.
Screw in the ring and hang the heater with the help of the chain (the length of the chain
can be regulated for . Place the heater between the fittings so that the pegs
should fit into the holes and screw the pegs (for industrial).
Before switching on, the heat-emit
5.
6.
7.
8.
ting plate should be cleaned with alcohol.
The flex must consist of three wires and have the diameter complying with electrical
power. (we recommended polyvinil 3x1,5-2,5)
Attach the end of the flex to terminals on the heater taking into account polarity marked
on the ends of the flex.
Heater connection to the stationary power point with thermoregulator is strictly according
to the scheme.
Thermoregulator should be placed 1,5 m., above the floor. Do not place it in the zone of
direct rays or in the draught to avoid malfunctions.
The heater is fixed on the chains to the screw ring which is screwed into the ceiling.
Installation scheme for “ПИОН”
The end of the chain with a wide link is placed into a hole on the back part of the heater
ATTENTION
While installation process, heat-emitting plate can be touched only in cotton
gloves. In case it is dirty it showed be cleaned with alcohol.!
5
ATTENTION !
°СThe included fixing device ensures safe connection of the heater to natural surfaces
(wood, concrete, metall etc.) In case of using artificial ceiling surfaces original
fixing devices are allowed with material thermoresistance not less then 80 .
General installation scheme.
!ATTENTION
АВ-
С-
“ПИОН”
distance to the ceiling, not less then 50 mm.
distance to the walls, not less than 500 mm.
distance to the objects in the heater functionary
zone, not less 500 mm.
L - distance between fittings can be
regulated.
6
С
Recommended minimum height of (H) heater fixation.
Model H
ПИОН 06 2,0
ПИОН 04 ,8 1
ПИОН 10 2,2
ПИОН 13 2,3
КВАДРО 05 1,8
ИКО-1.0 2,3
ИКО-0.5 2,0
ИКО-1.5 2,5
ИКО-2.0 3,0
ИКО-3.0 3,0
ИКО-4.5 3,5
ИКО-6.0 3,5
ЭЛ 2,520R
ЭЛ 2,830R
ЭЛ 3,040R
7.Electrical connection
:
ПИОН 04/06/10/13, КВАДРО 05, ИКО 0 5
ЭЛ 20 №1,2,3
ЭЛ 30 /40 ИКО 4.5 .0 № 4,5
Electrical connection should be fulfilled by qualified specialists in
accordance with the chosen scheme depending on the general power
and type of model
. /1.0/1.5/2.0/3.0,
R-schemes
R R, /6 - scheme
Take off the lid and connect
the wires according to
the scheme.
N
2
1
N
earth connection
zero
zero
Thermoregulator
RTR-E 6121
RTR-E 6163
Automatic power
L1
N
Scheme №1
Thermoregulator RTR connection for the general pressure up to 3,5 kWt.
Heater “ПИОН”
zero N
phase L1
earth connection
press and lift
7
Scheme №2
Thermoregulator RTR connection for the general pressure up to 3,5 kWt.
8
N
2
1
N
earth connection
phase
Thermoregulator
RTR-E 6121
RTR-E 6163
L1
N
Heater “ПИОН”
zero N
L1
earth connection
Heater “ПИОН”
zero N
phase L1
earth connection
Heater “ПИОН”
zero N
phase L1
earth connection
Automatic power
zero
phase
8.Start
1.
2.
3.
4.
Install the heater in accordance with Chapter 6.
ATTENTION ! At the beginning of exploitation the small amount of
evaporating conservatives may occur. It will disappear in the process
of work.
Complete the electrical connection in accordance with the scheme (Chapter 7).
When the heater is ready for work turn the handle of the thermoregulator and choose
the necessary temperature.
The chosen temperature will be ensured within 30 minutes.
9. Exploitation and technical support.
The heater generally doesn t need any service. To ensure its steady work it is
necessary to fulfill the following conditions (after the heater is switched off and
cool )
If necessary use a wet napkin to clean the frame and alcohol to clean the
heat-emitting plate.
Check the wire contacts and the stability of fixation (once a year).
! :
1.
2.
3.
Ensure proper isolation in the premises otherwise the work of the heater
will not be efficient due to cold air currents.
Heater exploitation conditions:
• -50°С до +air temperature from
air humidity up at
50°С;
• 80% +25°С
10. Possible disfunctions.
Possible
disfunctions
Ways of treatment
1.The heater
does not give
enough warmth
• 2 0+ -
•
Check the voltages on the terminals it should be
Check the termoregulator
Compare the temperature on your thermometre with the chosen
temperature on the termoregulator. The difference must be +
3 / 10V
/-2C• .
2. The heater
does not work
•
•
•
•
•
Check the voltage
Check the intactness of the connecting wire
Check the contact of the heater
Check the contact in the power plug
Check the thermoregulator
Consult our dealers
11. .Storage
The heater should be stored in its original package in the premises with
fluctuation of temperature from to air humidity not more than
The heater should be safe from bangs, dust and moisture. The heat-emitting
plate must be treated very carefully. It can t be touched, in case of necessity
it can be cleaned with alcohol.
-50°С +50°С, 80%.
11
Heater “ПИОН”
zeroN
phase L1
earth connection
Heater “ПИОН”
zeroN
phase L1
earth connectionе
phase3
Automatic power
L3
N
L2
L1
phase1
phase2
Scheme №3
Thermoregulator RTR connection for the general pressure more than 3,5 kWt.
N 2
1
N
Thermoregulator
RTR-E 6121
RTR-E 6163
Heater “ПИОН”
zero N
earth connection
9
earth connection
zero
phase L1
Magnetic switch
12. .Guarantee coupon
А. :
___________________________________________________________________
___________________________________________________________________
:________________________________________________
___________________________________________________________________
:__________________ __________________
:__________________________
The heater is accepted for guarantee service
Accepting date Service fulfilled date
Signature
( )
( )
organization
address
Defect manifestation
:
B
The heater is accepted for guarantee service
Accepting date Service fulfilled date
Signature
:
___________________________________________________________________
___________________________________________________________________
:________________________________________________
___________________________________________________________________
:__________________ __________________
:__________________________
( )
( )
organization
address
Defect manifestation
:
.
----------------------------------------------------------------------------
Coupon А
Coupon B
А. :
_____________________ ____________________________________ __________
_____________________ ____________________________________ __________
:___________________ _____________________________
_____________________ ____________________________________ __________
:_________________ _ _______ ___________
:_________________ _________
The heater is accepte d for guarantee serv ice
Accepting date Se rvice fulfilled date
Signature
( )
( )
organization
address
Defect manifestation
:
B
. :
___________________________________________________________________
___________________________________________________________________
:________________________________________________
___________________________________________________________________
:__________________ __________________
:__________________________
The heater is accepted for guarantee service
Accepting date Service fulfilled date
Signature
( )
( )
organization
address
Defect manifestation
:
13
14
13. .Guarantee obligations
The producer guaran
.
1. .
2.
3. :
• ;
•
;
• ;
•
;
•
;
• ;
•
80% +25°С°
4.
tees steady work of the heater during 3 years from purchase.
If any defects occur during the guarantee period as a fault of the producer, the
selling organisation will repair the heater free of charge or replace it on the
following conditions
The guarantee is valid only if the invoice is presented
The guarantee does not cover the damage caused as a result of changing
the device without preliminary written consent of the produser in order
to make it comply with local technical standards and safety norms.
The guarantee is not valid in case of
changing the construction of the device by the customer
incorrect exploitation with violation of user guidance rules, violation of
technical standards and safety norms
repair works fulfilled by unauthorized service centres or dealer
accidents, lightning, flood, fire and other reasons beyond the control of
the producer
defects acquired while transporting ( exept cases when transpoting is
carried out by autorized dealer)
defects of the system where the device was used
exploitation with increased voltage (more than 10% from normal), and
humidity more than at
The producer has the right to change the construction of the heater if
that does not spoil its technical characteristics.
Notes
15. .Sales certificate
Selling organization _____
Address
Sales date Signature _____________
______________________________ _________________
:_____________________________________________________________
:__________________ ____________________ _
14. .Reception certificate
_____________ ___ _________ __________
________________ _____________
Date of issue ______ Serial N ______
Producing plant representative _____________
ПИОН 06 ПИОН 10 ПИОН 13ПИОН 04
ПИОН heater complies with
Т 3468-001-84745490-2009.U
ПИОН group
ЭЛ 20R ЭЛ 30R ЭЛ 40R
КВАДРО 0.5
ИКО0.5 ИКО1.0
ИКО1.5
ИКО2.0
ИКО3.0 ИКО4.5
ИКО6.0
Open heating element group
15
Industrial group
Loading...