Valuxhome EF36, EF42, EF50, EF60, EF72 User Manual

IMPORTANT INSTRUCTIONS & OPERATING MANUAL

Armanni 36(EF36),Armanni 42(EF42),

Armanni 50(EF50),Armanni 60(EF60),Armanni 72(EF72)

WARNING

CAUTION

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.

Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.

NO VENTING REQUIRED

120V AC; 60 Hz; 1500 Watts

IMPORTANT:

IMPORTANT: It

the

first

the

the first

time.

first

time.

first time.

time. Keep

important

It is

is important

important to

Keep

the

Keep

the

Keep the

the instructions

read

to read

instruc

instructions

instructions safe

tions

these

read

these

read these

these instructions

safe

safe so

instructions

instructions carefully

that

so that

you

that

you

that you

you can

carefully

carefully before

can

refer

can

refer

can refer

refer t

before

before using

them

o them

them later

using

using the

later

later if

if necessary.

the

appliance

the

appliance

the appliance

appliance for

necessary.

for

IMPORTANT

【IMPORTANT

IMPORTANT INSTRUCTIONS

When using electrical appliances basic precautions should always be followed to reduce the risk of fire,

electric shock and injury to persons, including the following:

1) Read all instructions before using this heater.

2) This heater is hot when in use.

when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers,

clothes, and curtains at least 1 m from the front of the heater and keep them away from t

rear. In order to avoid overheating, do not cover the heater.

3) Extreme caution is necessary when any heater is used near children or the infirm and whenever the

heater is left operating and unattended.

4) Always unplug heater when not in use.

5) Do not operate any hea ter with a damaged cord or plug or after the heater malfunctions, has been

dropped or damaged in any manner, return heater to au thorised service facility for examination,

electrical or mechanical adjustment, or repair.

6) Do not use outd

7) This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never

locate heater where it may fall into a bathtub or other water container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings.

Arrange cord away from traffic area and where it will not be tipped over.

disconnect heater, turn controls to off, then remove plug from outlet.

10) Do not inset or allow foreign objects to enter any ventilation or exhaust openin

an electric sho ck or fire, or damage the heater.

11)

prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a bed, where openings many become blocked.

12)

heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, or

flammable liquids are used or stored.

13) Use this heater only as describes in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, or injury to persons.

14) DANGER-HIGH Temperatures may be generated under certain abnormal conditions. Do not

partially or fully cover or obstruct the front of this heater.

15) Replacement of the lamps should be done only while the heater is disconnected from the supply

circuit. 16）This appliance is not intended for use by persons (including children) with reduced physic al, sensory

or capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appli

supervised to ensure that they do not play with the appliance.

17) CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this

appliance must not be supplied through an external switching device, such as a timer, or connected to a

circuit that is regularly switched on and off by the utility.

INSTRUCTIONS

INSTRUCTIONS】

avoid burning, do not touch hot surface. If provided, use handles

oors.

ance by a person responsible for their safety.Children should be

he sides and

g as this may cause

UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 110-120 Volt grounded outlet.

Grounding

Grounding Appliance

【

This appliance is for use on 120 Volts.

receptacles. The green grounding lug extending from the

ground such as receptacle is available .

WARNING:

Keep the front of the appliance through which the heat is curtains and

remain

【

INSTALLATION

【

INSTALLATION

【

【INSTALLATION

INSTALLATION】

WARNING:Find a safe location and build a suitable hole for fireplace.Minimum clearance from the ceiling and the mantel must be at least 8 inches(200mm); near an outlet so an extension cord is not required.

other flammable objects at all time.

at the back of the appliance and must not be in contact with

Appliance

a properly grounded outlet box. The adapter should not be

To disconnect appliance, turn controls to off, then remove

】

minimum clearance from the front must be at least 3 feet(900mm).Choose a location

】

For connecting three-blade grounding type plugs to three -slot

adapter must be connected to a permanent

radiated at least 1 meter away from furniture,

Never use an extension lead. The mains cable must

any hot elements.

used if a three-slot grounded

plug from outlet.

Take model EF50 as an example.Prepare a wall with a framed opening of 46.5 inch(1180mm) wideX 21’’(533.4mm) high. Make sure the width of the wood block on both sides which used to fix the fireplace is 3’’(76mm).Make sure that the revealed wood block width on both sides is about 1 1/2’’(37.5mm) after finishing the plasterboard.Measure the depth D from the plasterboard surface to the wood block and write it down.

MODEL EF36 EF42 EF50 EF60 EF72

21’’

32.5’’

(82

6mm)

38.5’’

(978mm)

46.5’’

(1180mm) (1435mm)

56.5’’ (174

68.5’’ 0mm)

Before installing the in-wall fireplace,please read the following steps carefully.

Remove the two silver colored screws at both sides of the fireplace(See Step 1) Attention: no need the 2 silver colored screws when installing.

Step 1

Lift glass panel and pull it out upwards to you,leave screws out when installing in wall.(See Step 2)

Step 2

Removed the log from the bed if you want to change to the crystals,please remove the carton protection pack inside the fireplace first.

Kind attention:If you like the real log effect,please keep it on the bed and leave the crystals into a safe place for replacement in future.

(See Step 3)

Step 3

Put the optional fire crystals on the bed,please put the plastic strip on the bed first. (See Step 4)

Step 4

Warning

This carton includes GLASS!ALWAYS use extrme caution when handing glass. Failure to do so could result in personal injury or property damage.

Warning

ALWAYS

ALWAYS unplug

Failure to do so could result in electric

unplug

unplug this fireplace heater before

electric

electric shock

before

before assembly

shock

shock, fire

assembly

assembly or cleaning,

fire

fire, or p

cleaning,

cleaning, or

personal

ersonal

personal injury

injury

injury.

before

or before

before relocating.

relocating.

Put the Fireplace box into the wall, there're two hanger brackets in both sides of the fireplacebox, using

ST4X

6 pcs of ST4X

Figure A

Using the Philips Screw Driver"+"

ST4X

ST4X40 screws(each side with 3 screws) to lock the fireplace in the wooden wall.

Driver"+"

Driver"+" to fix the six screws on the wall between two sides Figure (A)

(A)

(A).Make sure

the front of the firebox is not lower than the surface of the wall.

The next step requires installation of a Glass panel!The manufacturer recommends that two adults install, the glass panel.Always use extrme caution when handling glass.Failure to do so could result in personal injury or property damage,please see the Figure (B).

Carefully set both hooks of the front glass panel onto the firebox.Note:make sure the glass fully attached to the firebox so that the control panel can work properly.This will keep the decorative glass in place and enable the control panel work well.

3 : 1

Figure B

Plug the power cord into a 110-120 Volt 15 Amp outlet.Make sure the outlet is in good condition and that the plug is not loose.NEVER exceed the maximum amperage for the circuit.DO NOT plug other appliances into the same circuit.

【

Special

【

Special

【

【Special

Special characteristics

1、The smouldering glow of the flames can hardly be distinguished from that of a real fireplace. 2、Produces the effect of a hot current of air. 3、Automatic and constant temperature control. 4、Fireplace can be both used as 5、Fireplace exchange d freely from LOG and Glass Media 6、Perfect for small 7、Timer ( 1hrs to 9hrs) 8、Operated with remote control and Manual Panel Switch 9、Dimmer (Five steps Flame adjust from Dimmer to Lighter)

characteristics

characteristics of

to mid-sized rooms

of this

Build-in the wall

this

this Electric

Electric

Electric Fireplace

Fireplace

Fireplace】

】

【

Safety

【

Safety

【

【Safety

Safety instructions

Only use the appliance in accordance with the instructions in this manual! It cannot be used for any

other purpose.

Never operate the appliance when the appliance itself or the main cable show any signs of damage.

In order to avoid overheating, do not cover the heater.

Be responsible when handling the packing material. Warning: plastic wrapping may be lethal to children.

Do not place the appliance next to a socket.

Never operate the heater on a program switch, timer switch or an

operation.

The heater is only suitable for indoor use.

Never use the heater in the bathroom, shower or near a swimming pool.

The heater must not be located immediately below a socket-outlet

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

Never leave small children unattended near the appliance.

In case of malfunction, disconnect the plug immed

When not in use for a considerable amount of time, u

Components should only be serviced by an approved electro technician.

instructions

instructions】

】

y other appliance for automatic

iately.

nplug the appliance.

【

switch on】

Plug in the appliance into the socket. Turn on the Power

Switch

The control Switch

Switch

Switch Panel

】

Power

Power Switch

Panel

Panel is on the bottom of tempered glass panel (See

Switch

(See

pic)

(See

pic)

(See pic)

pic)

Control Switch

Panel

【

POWER

Turns the appliance ON/OFF.

FLAME - Log

TIMER

TEMPERATURE

Controls Flame brightness.

5 Settings

: ( L1-L2-L3-L4-L5) Flame dims from L1 to L5.

F5 is the brightest setting.

Controls Log Flame change.

3 colors

: ( F1-F2-F3) Flame dims from F1 to F3.

Controls the Timer.

9 Settings:

(1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h,9h) Press button

until reach desired setting.

FLAME

Display Value

Temperature

HEATER

Controls the Heater. Press button to initiate the heate

(OFF) no heater or blower.

(LO), heater blows warm air (750W) (HI), heater blows hot air (1500W)

NOTE

: Heater functions cycle from OFF-LO-HI

1. Press once: Touch panel indicator becomes active.

2. Press again until desired setting is reached. Digital display shows setting circles as belo

Instruction

【

Instruction

【

【Instruction

Instruction for

for

Remote

for

Remote

for Remote

Remote Controller

Controller

Controller and

and

and Switch

Switch

Switch Panel

Panel

Panel】

Control Panel / Remote Control Operation

(Control panel POWER switch must be ON to use remote control.)

】

The touch display panel is shown by LED's on the front bottom right of the appliance. The LED's will appear on the bottom of the fireplace control panel.

WARNING : Do not move or remove the mesh trim panel, when the appliance is plugged in and operating. This will cause the remote control and touch panel to no longer function.

0 1 2 3 4 ... 12 13 14 15 N

17 18

19 20 21 ... 27 28 29 30

62 64

NOTE: Press the button for 10 seconds, the temperature

setting will switch from °C to °F. Same way from °F to °C.

66 68 69 ... 80 82 84 86

NOTICE

This remote control uses two AAA batteries (Not include d).

Instructions for battery installation are on the Remote Control battery compartment.

1. Unplug the power cord from the outlet.

2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.

3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are,

4. With the POWER switch in the OFF position, plug the power cord back int o the outlet.

5. If the problem continues, have your outlet and wiring inspected by a professional.

Buff using a soft cloth, slightly dampened with a citrus oil-based product.

DO NOT use brass polish or household cleaners as these products will damage the metal trim.

Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper

NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.

NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

When the heater is first turned on, a slight odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time.

NOTICE

To improve operation, aim the remote control at the front of the fireplace. DO NOT press the buttons too quickly. Give the unit time to respond to each command.

Remote Control Battery Information

NEVER dispose of batteries in ﬁre. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

Temperature Limiting Control

This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe

temperature, the heater will automatically turn OFF. To reset:

use a vacuum to clean the vent areas.

Care and Maintenance

Cleaning

ALWAYS turn the heater OFF and unplug the power cord from the outlet before

cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in

electric shock, fire, or personal injury.

NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury.

Metal:

Glass:

towel or lint-free cloth.

Vents:

Plastic:

CAUTION:

CAUTION: sharp

1. After installation, the power plug should be accessible.

2. If the power cord is damaged. It must be replaced by the manufacturer or its service agent or a

similarly qualified person in order to avoid a hazard.

3. The heater must not be located immediately below a socket.

4. The appliance is not intended for use by young children or infirm persons. Young children should be

supervised to en

5. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

6. In order to avoid overheating, do not cover the heater.

sharp

sharp edges!

edges!

sure that they do not pl

ay with the appliance.

Model:Armanni 36,Armanni 42,Armanni 50,Armanni 60,Armanni 72 Power supply:120V-60Hz Power consumption: 1500W Protection class: I Light bulb: LED

Valuxhome EF36, EF42, EF50, EF60, EF72 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual