Valore V-VMS603 User Manual

Valore WiFi Action Camera (V-VMS603)

Thank you for purchasing the Valore WiFi Action Camera (V-VMS7603)

Never miss another moment with the Valore WiFi action camera. Switch freely between Car DVR and sports action mode with this multipurpose camera and capture more of your surroundings in a single shot with 170° ultra wide-angle lens.

Important: Please read the user manual thoroughly before using your action camera.

Specifications: Package Contents:

• Image sensor: 10 Mega Pixels CMOS • WiFi action camera

• LCD: 1.5 inch • Waterproof housing

• Lens: 170° ultra wide-angle • Bicycle holder

• Resolution: 1920 x 1080 at 30fps • Base x7 1280 x 720 at 60fps • Lens cloth 1280 x 720 at 30fps • USB cable

• Input: DC5V/1A • Helmet Base

• WiFi distance: 10m • Bandages

• Battery type: Built-in 3.7V Lithium battery 700mAh • Suction cup

• Video format: MOV • Car charger

• Video codec: H.264 • Tethers

• Photo Format: JPEG

• Dimension (L x W x D):69 x 39 x 38mm

• Weight: 70g (with waterproof case 137g)

UNDERSTANDING THE PRODUCT

① ON / OFF / Mode switch

② REC / OK / Wi-Fi

WIFI

SOS

③ Up (Zoom in)/ IR Light

④ Menu / Back

⑤ Down (Zoom Out)

⑥ REC / OK / Wi-Fi

⑦ Playback

⑧ Microphone / Video Lock

⑨ Reset

⑩ AV Out

11 Micro USB Port

Micro SD Card Slot

MOUNTING THE CAMERA

1) Please make sure that you are following the regulations and laws set by your Country or states DMV (Department of Motor Vehicles) prior to mounting your camera. This will avoid any accidents and traffic violations that can occur if the camera is mounted in a location that is prohibited by law.

2) Using the suction cup and rotating bracket, mount the Wi-Fi Action Camera to the inside of your vehicles windshield (use the adjustment knob to loosen and tighten the Wi-Fi Action Camera as needed).

NOTE: The Wi-Fi Action Camera can also be used to record both exterior and interior (front and rear) of your vehicle. For interior recording, simply follow the steps above and rotate the camera so that the lens is facing the inside of your vehicle.

INSERT THE SD CARD

Insert your micro SD card into the Wi-Fi Action Camera’s micro SD slot. Make sure that you insert the in the correct direction as shown. The SD card will make a clicking sound, indicating it has been locked into the Carcam.

CONNECT THE POWER CABLE

1) Connect the car chargers cable into the Wi-Fi Action Camera’s power socket located on the bottom side of the Carcam.

WIFI

SOS

2) Depending on where you’ve chosen to mount the Wi-Fi Action Camera, run the power cable around the trim of your vehicle so that it will not obstruct your view while driving.

3) Insert the car charger into your vehicles cigarette lighter port as shown. A red light on the car charger will light up, indicating it is connected.

TURNING THE CAMERA ON

The two ways in turning on your Wi-Fi Action Camera

1) Start your vehicle and the Wi-Fi Action Camera will automatically turn on and begin recording.

2) Long press the power button manually to turn on the Wi-Fi Action Camera.

NOTE: The Wi-Fi Action Camera will automatically turn on/off whenever your vehicle turns on/ off, respectively.

LIGHT INDICATORS

Battery Charging Light (Red) Power Light (Blue)

Battery is currently charging (Red)

Power is on (Blue) Off

Wi-Fi Action Camera

battery is currently charing (Red)

Off

Power is off (No Blue Light)

Battery is fully charged (No Red Light)

Power is on (Blue)

USED AS ACTION CAMERA

A Quick Introduction of how to attach your camera to helmets, gear and equipment.

NOTE : Please switch to Sports Mode by pressing On/Off/Switch button before putting into the waterproof case.

SET DATE & TIME

1. Turn on your Wi-Fi Action Camera

• Press and hold the Power button until the “Welcome” screen appears

2. Press the Menu button twice to get to “Setup” menu

3. Select the Date&Time

• Press the “Down” button until Date&Time option is highlighted

• Press the “OK” button

4. Change the Date&Time

• Use the “Up” and “Down” buttons to change the date and the time

• Use the “ON/OFF/MODE SWITCH” button to go to next , and use the “OK” to confirm the change.

FORMAT YOUR SD CARD

1. Turn on your Wi-Fi Action Camera

• Press and hold the Power button until the “Welcome” screen appears

2. Press the Menu button twice until the “Setup” settings appears on the screen

3. Select the Format option

• Press the “Down” button until “Format” option is highlighted

4. Confirm Formatting

• Press “OK” to confirm your SD Card to be formatted

CHANGE TO DEFAULT SETTINGS

1. Turn on your Wi-Fi Action Camera

• Press and hold the Power button until the “Welcome” screen appears

2. Press the Menu button twice until the “Setup” settings appears on the screen

3. Select the “System” option

• Press the “Down” button until “System” option is highlighted ,and press OK .

4. Select the “Default Settings” option

• Press the “Down” button until “Default Settings” option is highlighted

5. Confirm “Default Setting”

• Press “OK” to confirm your Carcam will switch back to its default settings

WIFI

SOS

UP/ZOOM IN

The UP/ZOOM IN button is used to navigate through out the menu and make setting selections. It can also Zoom-In up to 2x its original distance while in video or photo mode.

（Note：Long press this button can enable/ disable the LED sensor when recording. ）

MENU/BACK

The MENU button allows access your Wi-Fi Action Camera menu settings. Pressing the Menu button again will access to Setup settings. While in the Car / Sports Video mode, you may access the Car / Sports Video and Setup settings. While in Photo mode, you may access the Photo and Setup settings. While in Playback mode, you may access the Playback and System settings.

DOWN/ZOOM OUT

The DOWN/ZOOM OUT button is used to navigate through out the menu and make setting selections. It is also used to Zoom-out while in video or photo mode.

REC/OK/ Wi-Fi

The REC/OK/Wi-Fi button is used to start and stop manual recording while in Video mode. It is also used to take pictures while in Photo mode. It can be used to make setting changes and select which event to view during playback. Long press this button to activate the Wi-Fi connection, Short press this button (when Wi-Fi is connected) to switch off Wi-Fi.

PLAYBACK

The PLAYBACK button is used to switch to Playback and view the video and photos been recorded. In Car/Sports/Photo Mode settings, press this button to enter Setup Settings.

Up / Zoom In

Menu / Back

Down / Zoom Out

REC / OK / Wi-Fi

Playback

MIC / Lock

MIC/LOCK

The MIC/LOCK button is used to switch on/off the audio record (long press). This function also locks the current video recording on your Wi-Fi Action Camera. By locking the video file, it will prevent the file from being manually deleted.

POWER / MODE

The POWER/MODE button is used to switch between Car mode, Photo and Sports mode , it also used to manually turn the Wi-Fi Action Camera on or off when needed(long press), but in most cases the Wi-Fi Action Camera will automatically turn itself on and off whenever the vehicle does.

SETTINGS

The Wi-Fi Action Camera’s settings are divided into 5 categories: Car Mode, Photo Mode, Sports Mode, Playback settings, and Setup settings.

NOTE: The “Setup” settings can be accessed from The Car Video, Photo and Sports Video settings.

CAR MODE SETTINGS

The Video configuration menu consists of settings and options that are used to configure the Wi-Fi Action Camera’s video recording settings. In the Car Video mode, press the “Menu” button to open up the Video configuration menu.

The Video settings consist of the following configuration options.

• Resolution – Video resolution configuration.

• Video Quality – Video quality configuration .

• Loop Recording – Overwrite configuration.

• Exposure – Adjust the amount of light that will affect your image sensor.

• Motion Detection – Enables/Disables motion detection recording.

• G-Sensor – G-force sensor configuration

• Parking Mode – Enable captures Hit and Run even when vehicle turns off .

• Date Stamp – Enables/Disables date stamp on recorded events.

RESOLUTION

The Wi-Fi Action Camera supports various video resolutions that you can select from. The higher the resolution, the better your video quality and the bigger the video size will be. Use the UP/DOWN keys to scroll through the options. Press the REC/OK button to select your desired settings. The available options include:

• 1080HD @30fps (default)

• 720P @30fps

• 720P @60fps

VIDEO QUALITY

The Wi-Fi Action Camera supports various video quality that you can select from. The higher the quality, the better your video quality will be. Use the UP/DOWN keys to scroll through the options. Press the REC/OK button to select your desired settings.

The available options include:

• Super Fine (default)

• Fine

• Normal

LOOP RECORDING

The loop recording option serves as two features: “Overwrite”&“Segment Length”. The overwrite feature allows the DVR to delete previously recorded events in increments when the SD card becomes full. The segment length feature is the length each recorded event can be before generating a new file. Use the UP/DOWN keys to scroll through the options. Press the REC/OK button to select your desired settings.

The available options include:

• Off – Disables overwrite and enables the default 24 hour segment recording.

NOTE: Setting this feature to off will create on long video which will stop recording as soon as the file exceeds the memory cards capacity.

• 1 Minutes– Enables the DVR to record/overwrite in 1 minute increments

• 3 Minutes (default)– Enables the DVR to record/overwrite in 3 minute increments

• 5 Minutes – Enables the DVR to record/overwrite in 5 minute increments

EXPOSURE

The exposure option lets you select the numeric exposure value for your video recording. The exposure feature consists of the following options:

+0.0 (defaut)

-2/3

-1/3

-1.0

-4/3

-5/3

+2.0

+4/3

+5/3

+1.0 +2/3 +1/3

-2.0

MOTION DETECTION

The motion detection option is used to enable/disable motion detection recording. While the Wi-Fi Action Camera is on, and is on standby, any movement in front of it will trigger a recording. The Motion Detection feature consists of the following options:

• Off/Disable(default)

• On/Enable

NOTE: Make sure the “Auto Power Off” function is set to “Off” to let the Wi-Fi Action Camera stay on during standby mode. When motion detection is active or turned ON, the G sensing will be deactivated. Please make sure motion detection is turned OFF for 2G and 4G sensor to function properly.

DATE STAMP

The date stamp option is used to enable/disable the date & time stamp from being displayed on playback videos. The date stamp feature consists of the following options:

• Off/Disable

• On/Enable (default)

G-SENSOR

The G-Sensor option is used to enable/disable the Wi-Fi Action Camera’s G-force/impact sensor which will lock the previous and current file from being deleted by the overwrite feature. The G-force acts as a sensor for the Wi-Fi Action Camera to secure any video files recorded in the event that the vehicle gets hit. Any force that is acted upon the vehicle will result in locking the current recording video file.

NOTE: Formatting the SD card will result in erasing all files, including the locked video files. The G-Sensor feature consists of the following options:

• Off/Disable

• 2G (default)- Represents 9.8m/s2 of force (passenger car turning on a corner)

• 4G- Represents 19.62m/s2 of force (bump on the road)

• 8G- Represents 39.2m/s2 of force (car collision)

PARKING MODE

Parking protection functionality offers peace-of-mind while you’re away from your vehicle. From collisions with other drivers who may bump into your vehicle and leave the scene. Any force that is acted upon the vehicle will activate the Wi-Fi Action Camera to switch on, record and lock the segment. Parking Mode feature consists of the following options:

• On

• Off (default)

SETUP SETTINGS

The Setup menu configures the Wi-Fi Action Camera’s system settings such as date and time, language, default settings, etc. It can be accessed from the Car Mode, Photo and Sports Mode. Press the Menu button twice to access the Setup menu.

The Setup settings consist of the following configuration options. Press the Menu Button twice.

• Sound – Beep / Volume / Audio Recording configuration.

• LED Sensor – Enables/Disables the infrared night vision (LED light).

• Auto Power Off – Auto System Shut Off configuration.

• Screensaver – Backlight/screensaver duration configuration.

• Date/Time – Date and Time configuration.

• Flip Screen – Flips your screen upside-down.

• Language – Language settings.

• TV Mode – TV mode configuration

• Frequency – Light frequency configuration.

• White Balance – White balance configuration.

• Wi-Fi Password – Change Device Wi-Fi password .

• System – Include Firm Version / Default Setting / Card info configuration .

• Format – Formats your SD card.

SOUND

The Sound option include Beep sound / Volume adjust / Audio Recording configuration. The Sound feature consists of the following options:

• Beep Sound – Enables/Disables button sound , press “OK” to switch .

• Volume – Volume up or down of the button beep sound , press “OK” to switch .

• Audio Recording – Enable / disable the audio recording along with video recording.

NOTE: Some states prohibit the use of audio recording. Please make sure you contact your local law enforcement agency if you are unclear on your Country or state laws and guidelines.

LED SENSOR

The LED Sensor enables/disables the LED night vision sensor, to control the LED light on/off.

• On

• Off(default)

AUTO POWER OFF

The auto power off option is an auto shut-down feature which, after a set time frame of inactivity (not recording) or standby, the Wi-Fi Action Camera shuts off. The auto power off feature consists of the following options:

• Off (default)

• 1 Minute

• 3 Minutes

• 5 Minutes

SCREENSAVER

The backlight option controls the time you want your screen to stay on before the screen turns off during video recording. For safety purposes, it is recommended for the screen on the Wi-Fi Action Camera to not stay on while the vehicle is in motion. The backlight feature consists of the following option:

• Off

• 1 Minute (default)

• 3 Minute

• 5 Minutes

DATE/TIME

The Date&Time option is used to set and configure the Wi-Fi Action Camera’s current date and time format. The button configurations are listed and described below:

• UP/DOWN – Use these to scroll through each selection

• POWER/MODE – This button scrolls through the date and time (i.e. Month to Day to Year,

etc.)

• REC/OK – Press this button to accept and save your date/time.

FLIP SCREEN

The image rotation flips the screen, vertically. This provides the option of having the Wi-Fi Action Camera mounted upside down. The image rotation setting feature consists of the following options:

• Off (default)

• On – Selecting this option flips the screen

LANGUAGE

The language option lets you change the language of the Wi-Fi Action Camera. The language feature consists of the following options:

• English (default)

• French

• Spanish

• Italian

• Chinese

• Russian

• Japanese

FREQUENCY

The frequency option switches between the two most commonly used refresh rates “60Hz” and “50Hz”. By default the Wi-Fi Action Camera is set to 60Hz which is standard for United Sates and Japan. The frequency feature consists of the following options:

•50Hz – Standard for Europe and China.

•60Hz (default) – Standard for United Sates and Japan.

WHITE BALANCE

The white balance option lets you remove unrealistic color casts, so that objects which appear white in person are rendered white in your photo. The white balance feature consists of the following options:

• Auto (default)

• Daylight

• Cloudy

• Tungsten

• Fluorescent

Wi-Fi Password

The Wi-Fi Password option is used to set and configure the Wi-Fi Action Camera’s current Wi-Fi password.

• UP/DOWN – Use these to scroll through from “1” to “10” or “a” to “z” .

• POWER/MODE – This button scrolls through from the previous to next .

• REC/OK – Press this button to accept and save your new Wi-Fi password.

SYSTEM

This option Include Firm Version / Default Setting / Card info configuration.

• Default Settings - The default setting option is used apply the Wi-Fi Action Camera’s manufacturer default settings.

• Firm Version - The version option is used to view the Wi-Fi Action Camera’s firmware.

• Card info - The Card info option is used to view the information of the Memory card.

NOTE:

Update firmware:

1) To update your Wi-Fi Action Camera’s firmware, make sure you have the firmware file downloaded and pasted it into the root of the micro SD card on your PC.

2) Insert the micro SD card into your Wi-Fi Action Camera device.

3) Turn on the Wi-Fi Action Camera. The power light will turn on and the screen will remain black.

4) Wait for the firmware to install into the Wi-Fi Action Camera

5) Once complete, the Wi-Fi Action Camera screen will display its welcome screen

6) To check if the firmware has been updated, go into the Setup Settings menu and check the “Version”

NOTE: Please remember to remove the firmware file from your micro SD card to prevent the firmware from flashing every time you restart your Wi-Fi Action Camera device.

FORMAT

The format setting option is used to erase all files inside your SD card, including protected files. The format feature consists of the following options:

• Cancel

• Ok

PHOTO MODE SETTINGS

The Camera configures the Wi-Fi Action Camera’s photo snapshot settings. In the Photo mode, press the “Menu” button to open up the Camera configuration menu.

The Camera settings consist of the following configuration options:

• Resolution – Photo resolution configuration.

• Quality – Picture quality configuration .

• Capture Mode – Used to configure single or timed snapshots.

• Burst Mode – Burst mode option.

• Date Stamp - Enables/Disables date stamp on recorded events.

• Sharpness – Image sharpness configuration.

• Exposure – Image exposure adjustment.

RESOLUTION

The Wi-Fi Action Camera supports various “Mega Pixel” resolutions that you can select from. The resolution feature consists of the following options:

• 10MP

• 8MP

• 6MP

• 3MP (default)

QUALITY

The Wi-Fi Action Camera supports various picture quality that you can select from. The higher the quality, the better your video quality will be. Use the UP/DOWN keys to scroll through the options. Press the REC/OK button to select your desired settings. The available options include:

• Super Fine (default)

• Fine

• Normal

CAPTURE MODE

The capture mode option lets you configure how the Wi-Fi Action Camera will operate every time the snap shot button is pressed. For example, you can set it to take an instant snap shot every time or you can implement a timer delay which will automatically take a snap shot when the set time has expired. The capture mode feature consists of the following options:

• Single (default)

• 2S Timer

• 5 S Timer

• 10 S Timer

BURST MODE

The burst mode option lets you enable the “multiple shot” option. When you take a snapshot, it will take multiple shots in a single take, up to 5 pictures. The burst mode feature consists of the following options:

• Off (default)

• 5 pictures

DATE STAMP

The date stamp option lets you enable or disable the time stamp from being displayed on all the photos. The date stamp feature consists of the following options:

• Off

• On (default)

SHARPNESS

The sharpness option lets you select the image sharpness of the photos being taken. They make edges appear more defined by darkening the darker pixels and brightening the brighter pixels. The sharpness feature consists of the following options:

• Strong

• Normal (default)

• Soft

EXPOSURE

The exposure option lets you select the numeric exposure value for your snap shots. The exposure feature consists of the following options:

The Video settings consist of the following configuration options:

• Resolution – Video resolution configuration.

• Video Quality – Video quality configuration .

• Exposure – Adjust the amount of light that will affect your image sensor.

• Anti-Shaking – Enables/Disables anti-shaking configuration.

• Date Stamp – Enables/Disables date stamp on recorded events.

RESOLUTION

+0.0 (defaut)

-2/3

-1/3

-1.0

-4/3

-5/3

+2.0

+4/3

+5/3

+1.0 +2/3 +1/3

-2.0

your desired settings. The available options include:

• 1080HD @30 fps (default)

• 720P @30 fps

• 720P @60 fps

VIDEO QUALITY

• Super Fine (default)

• Fine

• Normal

EXPOSURE

The exposure option lets you select the numeric exposure value for your video recording. The exposure feature consists of the following options:

Anti-shaking

The Anti-shake enables/disables the anti-shake function in Sports mode.

• On (default)

• Off

DATE STAMP

The date stamp option is used to enable/disable the date & time stamp from being displayed on playback videos. The date stamp feature consists of the following options:

• Off/Disable

• On/Enable (default)

+0.0 (defaut)

-2/3

-1/3

-1.0

-4/3

-5/3

+2.0

+4/3

+5/3

+1.0 +2/3 +1/3

-2.0

PLAYBACK SETTINGS

The Playback settings menu provides actions for video clips or photos that have been recorded in the Carcam. In the Playback mode, you can press “OK” button to play/pause and press the “Menu” button twice to open up the Playback configuration menu. The Playback settings consist of the following configuration options:

• Delete – Delete video/photo files

• Protect – Protect video/photo files

DELETE

This option allows you to delete video or photo files in your SD card. You may choose to delete one file at a time or delete all simultaneously. The available options include:

• Delete Current – Delete selected video/photo

• Delete All – Delete all videos and photos in the Carcam

NOTE: Any protected files will not be deleted if “Delete All” is selected.

PROTECT

The Protect option helps prevent any video files or photo files from being deleted. When selecting “Delete All”, the protected file will not be erased.

NOTE: When “Formatting” the SD card, protected files will also be erased. The available options include:

• Lock / Unlock Current – Protects the selected file. If the file is already protected, selecting this option will unprotect the file.

• Lock All – Locks all files on the SD card.

• Unlock All – Unlocks all files on the SD card.

PLAYING BACK VIDEOS

You can play back recorded events using two methods; directly from the Wi-Fi Action Camera or on a computer.

Wi-Fi Action Camera

To play back events directly from the Wi-Fi Action Camera navigate to the playback screen using the Playback button. You can use the following buttons to play back and delete the recorded events: NOTE: Traffic lights may flash during playback.

COMPUTER

To playback recorded video on a PC or Mac:

1. Remove the Micro-SD card from the camera by gently pushing on the SD card allowing it to pop out from its slot.

2. Insert the Micro-SD card into a Micro-SD card reader (not included) connected to your PC (your PC should load the SD card as a new Removable Drive).

3. When prompted, select the “Open folder to view files” option to view its contents (you should see folders labeled “LOCK” ,”JPG”,”VIDEO”,”SPORT”).

4. Open the LOCK folder to view a list of all the recorded video locked by G-force .

5. Open the JPG folder to view a list of all the Pictures.

6. Open the VIDEO folder to view a list of all the recorded video in Car mode.

7. Open the SPORT folder to view a list of all the recorded video in Sports mode.

8. Once inside the folder you can double-click any of the recorded MOV or JPG files to open them up in your default media player.

WI-FI Control

Download the free Wi-Fi viewer app from IOS App Store or Android Apps on Google Play

• Download the App named “ ismart DV “ from App store or Google Play

Turn on the Wi-Fi on device

1. Turn on your Wi-Fi Action Camera

• Press and hold the Power button until the “Welcome” screen appears

2. Turn on your Wi-Fi

• Press and hold the REC/OK button until the “ Waiting for Wi-Fi connection..” screen appears.

BUTTON ACTION DESCRIPTION

REC/OK

Press once (when not playing back video)

-Selects the highlighted event to playback/view

-Confirm an option when prompted

Press once (when not playing back video)

-Pause the video

MODE

Press once -Switches to “Video” mode

Press once (during multiple file view)

-Used to navigate through the recorded events

Press once (during video playback) - Fastforward the video

DOWN

Press once (during multiple file view)

-Used to navigate through the recorded events

Press once (during video playback) -Rewind the video

Connect the device Wi-Fi

1. Enter the Settings of your smartphone

• Turns the Wi-Fi on

• Find the Wi-Fi named “view-0001” and select .

2. Connect the Wi-Fi

• Type in the initial password “12345678” and get connected

• “ Wi-Fi connection is ready..” screen appears on Wi-Fi Action Camera.

Application

1. Record

• Choose the Camcorder icon at lower right corner to switch to Video Recording mode .

• Choose the Camera icon at lower right corner to switch to Photo Capturing mode .

• Press the small red spot in the middle of the screen bottom to REC .

2. Download / Delete files

• Press the icon at lower left corner to enter files browser and download / delete the files

3. Change Settings

• Press the Settings icon at upper right corner to enter device settings .

• Press the Resolution / AWB / Timer icon in the middle of the screen to change the settings.

LCD Size 1.5” TFT LCD

Image Sensor Digital HD color CMOS

Viewing angle 170°A+ grade high -resolution ultra wide -angle

Language for options English /French/Spanish/Italian/ Traditional Chi nese/ Simplied

Chinese/Japanese/ R ussian

Video resolution 1080P 1920*1080 @ 30fps , 720P 1280*720 @ 30fps ,

720P 1280*720 @ 60fps

Video/Photo formats MOV / JPEG

Recording video format M-JPEG

Photo pixels 3M /6M/8M/10M Pixels

SD slot Micro SD card (supports up to 32GB, class 4 or above)

Overwrite Yes

Wi-Fi Yes,Built -in

Microphone

Built-in (Menu: On/O)

Speaker Built-in

Recording frame rate 30fps/60fps

Video recording mode

*Auto record when the ignition is turned on and stop when engine is turned

o (with car cigarette lighter cable connected)

*Manual record by pressing REC button

*Video Motion Detection record

Shooting mode (photo) Single, 2s timer, 5s timer, 10s timer,

Frequency 60Hz/50Hz

TV standard NTSC/PAL

USB port USB 2.0

PC mode (via USB) Mass Storage or PC Camera

Power supply Input: DC12V -24V, Output: 5VDC / 1.0A

Rechargeable battery

3.7V / 700 mAh (Charging time: 120-Minutes. Recording time: 90 -Minutes.

Standby Time: 120-Minutes)

Camera size (L*W*H) 2.80 ”x1.2 ”x1.5 ”(without bracket and waterproof case )

Operating temperature -10°C to 50 °C (14 °F~122 °F)

Non-Operating temperature

-20°C to 65 °C ( -4°F~149 °F)

Operating humidity

≤

85% RH

TECHNICAL SUPPORT & WARRANTY

• For Technical Support, email us at v.info@valore.sg.

• For Warranty Registration, visit www.valore.sg.

When using this product, the safety precautions below must be taken to avoid possible legal lia-bilities and damages. Retain and follow all product safety and operating instructions. Observe all warnings in the product operating instructions. To reduce the risk of bodily injury, electric shock, fire and damage to the equipment, observe the following precautions.

Cautions:

Read all the instructions and warnings carefully prior to using this product.

• DO NOT use this product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool .

• DO NOT place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

• DO NOT disassemble this product. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock during subsequent use.

• DO NOT use this product to infringe on one’s privacy, spying intercepting and related activities are illegal and punishable by law. Monitoring one’s private activities without consent is illegal and this product is not designed or manufactured for these purposes.

• DO NOT use this product to carry out any illegal activities such as sneak preview, etc. Valore shall not be responsible for any consequences of illegal conducts made by users.

• DO NOT put the plastic packaging bags in reach of children or babies. Plastic bags can create a suffocation hazard when placed over the nose and mouth.

• DO NOT plug the AC adapter into the outlet in improper situations.

• Plugging in an AC adapter with wet hands might cause electric shock.

• Plugging in the AC adapter unsteadily might cause fire or electric shock.

• DO NOT cover the AC adapter when it is connected to an outlet, place the adapter near heaters, or put it on the floor which is equipped with a heater. The above mentioned operation might cause fire or incidents.

DISCLAIMER & TRADEMARKS

All information, trademarks, logos, graphics, and images (“Materials”) provided on this user manual are copyrighted or trademarked and are the property of Valore Lifestyle Pte Ltd. Any unauthorized use of any material contained on the instruction manual may violate copyright laws, trademark laws, laws of privacy and communications statutes.

The trademarks, service marks and logos used and displayed in the Materials are registered and unregistered trademarks and service marks of Valore and others. All other registered and unregistered company names, product names and marks mentioned herein the (“Materials”) are the property of their respective owners and may be trademarks or registered trademarks.

Valore V-VMS603 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual