08/51891/0 Issue 1
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)
EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC.
UK
Installation & User Instructions for Medway & Teviot
Side Switch Control Electric Suites
These Suites include the Balmoral & Savena Ecolite Electric Fires
Note: Illustration in g 1 & 2 shows the Savena
electric re in the Teviot suite. The Medway suite
also comes with side switch control and is tted
with the Balmoral electric re.
Illustration in g 1 & 2 shows the Teviot suite.
The Medway suite is also available with side
switch control.
Illustration in g 3 shows the contents of the side
switch control electric suite, 2no. screws, 2no.
wall plugs, 1no. fully assembled suite.
Illustration in g 4 shows the side switch controls
featured on the leg of the surround.
2
1
3
4
The appliance must be positioned so that
the plug is accessible.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or a similarly qualied person in order
to avoid a hazard.
Keep the supply cord away from the front of
the appliance.
Warning: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through
an external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.
CAUTION - Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
The heater carries the Warning symbol,
indicating that it must not be covered.
This instruction can be found at
WWW.VALOR.CO.UK
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
General
Unpack the electric suite carefully and retain the packaging for possible
future use, in the event of moving or returning the electric suite to your
supplier.
The re incorporates a ame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the ame effect on its own only requires little electricity.
Before connecting the electric suite check that the supply voltage is the
same as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the ame effect. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This electric suite must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Fixing - see Fig. 1&2
The electric suite should be securely xed to a wall by the brackets supplied.
Also included with the suite is wall plugs and xing screw to t the suite to
the wall (Note: wall plugs supplied are only suitable for block walls, xing
for stud walls are not included)
Locate the suite against the wall in the desired location and mark the wall
through the xing brackets, remove the suite and drill the wall with a 6mm
diameter drill bit to a depth of 35mm.
Insert the wall plug and ensure the end of the wall plug is ush with the
surface of the wall.
Reposition the suite back into the desired position and line up the holes
on the xing brackets with the holes on the wall plugs, when the suite is
positioned correctly insert the screws through the xing bracket and into
the wall plug and tighten this can be done with a screw driver or with a
power tool. Ensure the suite is securly tted on both sides of the suite.
Continued
UK
Important Safety Advice
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of re, electrical shock and
injury to persons, including the following:
If the appliance is damaged, check with the
supplier before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings
of a bath, shower or swimming pool.
Do not locate the appliance immediately
below a xed socket outlet or connection
box.
The appliance carries the Warning symbol
DO NOT COVER, indicating that it must not
be covered.
This appliance can be used by children
aged form 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by Children
without supervision.
Children of less than 3 years should be
kept away unless continuously supervised.
Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or installed
in its intended normal operating position
and they have been given supervision or
instruction concerning use of the appliance
in a safe way and understanding the hazards
involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate
and clean the appliance or perform user
maintenance.
Do not use this appliance in series with
a thermal control, a program controller, a
timer or any other device that switches on
the heat automatically, since a re risk exists
when the appliance is accidentally covered
or displaced.
Ensure that furniture, curtains or other
combustible material are positioned no
closer than 1 metre from the appliance.
In the event of a fault unplug the appliance.
Unplug the appliance when not required for
long periods.
Although this appliance complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
UK
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Valor
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire.SO30 2DF
TEL: 0844 879 3588
FAX: 0844 879 3583
Republic of Ireland Tel. 01 8424833
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of GDC Group Ltd.
Manual Controls - see Fig. 4
Three switches provide a choice of heat setting. Each switch is activated
when the bottom half of the switch is pushed in.
Switch 1 Controls the electricity supply to the heater.
Note: This switch must be in the ON position for the heater
to operate with or without heat.
Switch 2 Provides 950 W heat output.
Switch 3 Provides 1900 W output when used in conjunction with switch2
Thermostat
In order to maintain a certain room temperature, set the thermostat knob
to ‘max.’. Operate the appliance at full power until the required room
temperature is reached. Turn back the thermostat knob until the appliance
switches off. This temperature will be kept almost constant by the thermostat
switching on and off automatically.Please note that the appliance will only
operate when the thermostat setting is higher then the room temperature.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the electric re to prevent damage
due to overheating. This can happen if the heat outlet was restricted in
any way. The electric re will switch on once the obstruction has been
removed and the electric re has cooled. If the cut-out continues to operate
intermittently, the electric re should be switched off and a service agent
contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) bulbs in place of
conventional bulbs . These generate the same light levels as conventional
bulbs, but use a fraction of the energy consumed. These LED bulbs are
maintenance – free and will not require replacing during the life of the
product.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners.
The glass viewing screen on the electric re should be cleaned carefully
with a soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or uff the soft brush attachment of
a vacuum cleaner should occasionally be used to clean the outlet grille
of the fan heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for
recycling advice in your country.
Model Number
The Model & Serial number of your product is displayed in 2 locations, rst
is on the rating plate on the rear of your product, the second is on the fuel
bed at the rear of the fret. If your product is xed in position the easiest
position to gain access to the model/serial number is by removing the
fret, remove the fret by lifting it up and then pulling it out from the re, you
should have this information to hand when contacting customer service.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product free
of charge (excluding lamps & subject to availability) provided it has been
installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales information or assistance with this product,
please contact 0844 879 3588 (UK) or 01 842 4833 (R.O.I.)
Please retain your receipt as proof of purchase.
Loading...