OPERATING INSTRUCTIONS
GV60 SYMAX
Valor 10 Electronic Ignition Remote Control System
For use with Valor heaters model 1500, 1600, 1700, 1800, 2100 and 2200K
Radio Frequency
918.0 MHz for USA and Canada.
This device complies with Part 15 of the FCC Rules
and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference,
and
Remote Control Initial Pairing
The receiver and the handset of the remote control
system must be initially paired before the fi rst use.
(Note that batteries must already be installed in the wall
mounted battery holder)
1. Insert two 1.5 V AAA alkaline batteries in the handset.
2. Locate the Reset button on the front side of the receiver.
3. With a thin object, press and hold the receiver’s RESET
button until you hear one short and one long beeps.
After the second beep, release the reset button.
4. Within the subsequent 20 seconds, press and hold the
button on the remote handset. will be displayed on the handset during the pairing sequence.
You will hear two short beeps confi rming the pairing
is done.
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
RESET
Reset button
If you hear one long beep, the pairing sequence has failed
or the wiring is incorrect.
This is a one time pairing only and is not required when
changing the batteries of the handset or battery holder.
The remote control system is now ready to use.
June 2019
©2019, Miles Industries Ltd.
1
Remote Control Operation
NOTE: Before using the remote control system for the first time, the receiver and the handset must be paired. See
the section Remote Control Initial Pairing on the fi rst page of this manual.
Main Display
Countdown Timer
ON
Program Mode
To Turn On Fire
NOTE: When pilot ignition is confi rmed, motor
automatically turns to maximum fl ame height.
OFF
Time
Temperature
Signal Indicator Child Proof
Thermostatic Mode
Battery Status
AM
PM
Fan (if included)
°F or °C
Light
Eco
Auxiliary Feature (not used)
CAUTION: If the pilot does not stay lit after
several tries call your local service technician or
gas supplier.
Mode
One-Button lighting (default):
Two-Button lighting: +
simultaneously
Press and hold for 4 seconds, until 8
short beeps and a blinking series of
lines confi rms the start sequence has
begun. Release button.
Main gas fl ows once pilot ignition is
confi rmed.
Handset automatically goes into
manual mode after main burner
ignition.
Standby Mode (Pilot Flame)
Press and hold to set appliance to
pilot fl ame.
To Turn O ff Fire
Press to turn OFF.
Note: There is a 2 minute delay after
switching off before the next ignition is
possible.
CAUTION: Always check the fi re and pilot visu-
ally to ensure they are off .
Flame Height Adjustment
To i n cre a s e fl ame height, press and
hold .
To d ec r e a se fl ame height, press and
hold . You may hold the button
down until the fi re is set to pilot fl ame
only.
AM
2
Designated Low Fire and High Fire
To go to low fi re, double-click . “LO”
is displayed.
Note: Flame goes to high fi re fi rst
before going to low fi re.
AM
1. Install batteries. All icons are displayed and fl ashing.
2. While the icons are fl ashing, press the relevant func-
tion button and hold for 10 seconds.
3. The function icon will fl ash until deactivation is com-
plete. Deactivation is complete when the function
icon and two horizontal bars (
) are displayed.
To deactivate functions:
To go to high fi re, double-click
is displayed.
. “HI”
AM
Choosing 1-Button or 2-Button Ignition
On the remote control handset, you can choose a
1-button or 2-button ignition. You can also choose to
activate or deactivate some of the functions. By default,
the handset is set to a 1-button ignition.
To change from 1-button to 2-button ignition, remove
the batteries, wait 10 seconds, reinsert batteries, and
immediately when the display fl ashes, press and hold
the button for 10 seconds.
is displayed and 1 is
ON
fl ashing. When change is complete, 1 changes to 2.
To change from 2-button to 1-button ignition, proceed
the same as above.
is displayed and 2 is fl ashing.
ON
When change is complete, 2 changes to 1.
Deactivating or Activating Functions
These functions are active by default, but can be
deactivated at any time:
• Child Proof
• Program Mode
• Thermostatic Mode
• Eco Mode
• Circulating Fan Operation
• Countdown Timer
Note: If a deactivated button is pressed, there is no
function, and the two horizontal bars are displayed.
To activate functions:
1. Install batteries. All icons are displayed and fl ashing.
2. While the icons are fl ashing, press the relevant func-
tion button and hold for 10 seconds.
3. The function icon will continue to fl ash until activa-
tion is complete, and then turn solid. Activation is
complete when the function icon is displayed.
Setting Celsius or Fahrenheit
To change between °C and °F, press
and hold + simultaneously.
Note : °C = 24-hour clock
°F = 12-hour clock
PM
Setting the Time
1. Press + simultaneously.
Day fl ashes.
2. Press + to select a number
to correspond with the day of the
week.
• 1 = Monday
• 2 = Tuesday
• 3 = Wednesday
• 4 = Thursday
• 5 = Friday
• 6 = Saturday
• 7= Sunday
3. Press + simultaneously. Hour fl ashes.
AM
PM
4. To select hour press or .
5. Press + simultaneously. Minutes fl ash.
6. To select minutes press or .
7. To con fi rm, press + simultaneously or wait.
3
Loading...