Valor GV60 PLUS Operation Manual

Operation Manual

GV60 PLUS

GV60 PLUS Electronic Ignition Remote Control

For Valor heaters 530, 534, 650, 738, 739M, 1500, 1600, 1700, 1800, MF28 and RF24

Synchronize Remote Control

The receiver and the handset of the remote control sys­tem must be initially synchronized before the fi rst use.

1. Insert alkaline batteries in the remote control
battery holder and handset. The battery holder is
located beside the receiver, near the control valve
under the fi rebox, left of the fi rebox or beside the
wall switch.

2. With a sharp object, press and hold the receiver’s
reset button until you hear one short and one long
beeps. Release the reset button after the second
beep.

3. Within the subsequent 20 seconds, press the small

fl ame button ( ) on the remote handset until you
hear two short beeps confi rming the sychronization
is set. If you hear one long beep, this indicates the
code learning sequence has failed or the wiring is
incorrect.

This is a one time setting only and is not required when
changing the batteries in the remote receiver. The
remote control system is now ready to use.

June 2019

1

Remote Control Operation

O

Current

temperature

(F or C)

Current time
(12 or 24 hour clock)

Modes (Manual,
Temperature, Timer)

Handset
sensor

Battery status

Current

programmed

period (Timer)

Period

start or end

(Temp, Timer)

Radio Frequency

315 MHz for USA and Canada.

This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,
including interference that may cause undesired
operation.

NOTE: Before using the remote control system for
the fi rst time, the receiver and the handset must

be synchronized. See the section Synchronize Remote
Control on page 1.

IMPORTANT: BEFORE YOU BEGIN, please note that on this
system, the settings of time, temperature and automatic
ON/OFF can only be programmed when the function
display is fl ashing. Be patient when programming as it
can take a few seconds to set.

Note: In the TEMP or TIMER modes, the remote handset
senses the room temperature and adjusts the fl ame
accordingly.

To communicate, the handset should be within 15feet
(4.5 meters) of the fi replace.

Do not leave the handset on the mantel or hearth.

Turn Fireplace ON

Press + buttons until you hear a
short beep; release buttons.

Beeping continues until pilot is lit.

Burner lights to maximum fl ame height
and handset goes automatically to
manual (MAN) mode.

NOTES:
On the valve, MAN button must be at ON, in full
counter-clockwise position .

ON/OFF switch (if equipped) must be in I (ON) position.

Turn Fireplace OFF

Press button.

When pilot is just turned off , wait 2
minutes to light it again.

Standby Mode (Pilot Flame)

Press and hold to set fi replace
to pilot.

FF (returns to set mode,

2

SET (scrolls through

modes and settings)

turns the burner and

WKHSLORWR΍

/DUJHȵDPHEXWWRQȵDPHV

up, sets hours, temperature)

6PDOOȵDPHEXWWRQȵDPHV
GRZQDQGR΍VHWVPLQXWHV

temperature)

Adjust Flames Height

With pilot lit, press and hold buttons:

= increase fl ame height

= decrease fl ame height or

set to pilot

For fi ne adjustment, tap buttons.

Express Low and High Fire

Double-click buttons:

= increase fl ame to maximum

height “HI”

= decrease fl ame minimum

height “LO”

NOTE: Flame goes to high fi re fi rst
before going to designated low fi re.

x 2

x 2