GV60NTK
Non-Thermostatic Kit
For use with Valor GV60 PLUS or MAX* Remote Control Systems ONLY
INSTALLATION & OPERATION INSTRUCTIONS
Non-Thermostatic Handset
The handset GV60NTK is used with the Valor GV60
PLUS or MAX
and the set the fl ame height. It has no thermostat
or programming functions and it does not shutdown
automatically. The handset shows the current time and
the room temperature.
* receivers to turn the fi re on or off
*NOTE: The handset GV60NTK does not operate
the fan control, the lighting control or the duplex
burner fi replaces with GV60 MAX systems.
Synchronizing the NT handset to the remote
control receiver
The receiver and the handset of the remote control system must be initially synchronized before the fi rst use
of a new handset.
Current room
temperature
Current time
Valor
logo
only
G6R-H3D6
The non-thermostatic
(NT) handset is
identifi ed with a Valor
logo only. It shows
the current time and
room temperature.
The number shown
on its back cover
label is G6R-H3D6
Back cover label
1. Insert alkaline batteries in the remote control
receiver and handset. The receiver is located left of
the control valve under the burner module.
2. With a sharp object, press and hold the receiver’s
reset button until you hear one short and one long
beeps. Release the reset button after the second
beep.
3. Within the subsequent 20 seconds, press the small
fl ame button ( ) on the remote handset until you
hear two short beeps confi rming the sychronization
is set.
This is a one time setting only and is not required when
changing the batteries in the remote receiver. The
remote control system is now ready to use.
4003044-02
© Copyright Miles Industries Ltd., 2011.
www.valorfi replaces.com
• The one-hour feature is maintained when using a
1265WSK wall switch.
• One handset can be used to synchronize multiple
receivers to activate the one-hour feature.
• Synchronizing the receiver again with a thermostatic
handset will reactivate the thermostat, programming
and auxiliary functions.
Remote Control Operation
Current
temperature
(F or C)
Current time
(12 or 24 hour clock)
Handset
sensor
Battery status
NOTE: Before using the remote control system with the new NT handset, the receiver and the new handset
must be synchronized. See previous page of this manual.
IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings of time and temperature can only be
set when the function display is fl ashing. Be patient when setting the handset as it can take a few seconds to set.
Large ame
Display Overview
To communicate, the handset should be within 15 feet
(4.5 meters) of the fi replace.
Do not leave the handset on the mantel or hearth.
(turns the burner
OFF
and the pilot o)
button (ames
up, sets hours,
temperature)
Small ame
button (ames
down and o,
sets minutes)
Handset Overview
Turning your fi replace ON
IMPORTANT: When the pilot is lit, the valve motor
turns automatically to maximum fl ame height.
1. Make sure that the MAN knob on the valve is in ON position.
2. Make sure that the switch on the valve is in the I position (except on 650 and 1500 fi replace
models).
3. Press and hold the OFF and (large fl ame) buttons until you hear a short acoustic signal.
Release the buttons.
The acoustic signals will continue until the pilot lights. The fl ame will be at maximum height until
the remote control reads the temperature (factory set) and will then adjust the fl ame accordingly.
Turning your fi replace OFF
1. Press the (small fl ame) button to reduce the fl ame to pilot.
2. Press the OFF button to turn the pilot off.
Alternately, you can press the O button on the switch if you won’t use your fi replace for a long
period of time, if you cannot locate your remote control handset or if you wish to change the
batteries (except on 650 and 1500 fi replace models).
2
Loading...