Valor 530IP, 530ICN/ICP, 530ILN, 530ICN, 530IRN Installation & Owner's Manual

PORTRAIT

DV Gas Fireplace Heater

530ILN/ILP (logs), 530ICN/ICP (coals),

530IRN/IRP (rocks)

Installation & Owner’s Manual

!

A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.

! WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.

— Do not store or use gasoline or other

fl ammable vapors and liquids in the
vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do

not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.
▪ If you cannot reach your gas supplier,

call the fi re department.

— Installation and service must be

performed by a qualifi ed installer, service
agency or the gas supplier.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

This manual contains instructions to install the EN­GINE ONLY. A front trim kit is REQUIRED to install

the engine as it affects the framing cavity and posi­tion of the engine. A barrier screen is provided with
the front or trim kit. Refer to the manual supplied

with the front for framing and fi nishing.

This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.

This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.

This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.

This appliance is suitable for installation in a
bedroom or bed sitting room.

Ce guide est disponible en français sur demande.

INSTALLER

Leave this manual

with the appliance.

CONSUMER

Retain this manual

for future reference.

Please read this manual
BEFORE installing and
operating this appliance.

4001754-20

©2014, Miles Industries Ltd. All rights reserved.

Table of Contents

W

A

R

R

A

N

T

Y

P

R

O

G

R

A

M

V

A

L

O

R

C

O

M

F

O

R

T

V

A

L

O

R

C

O

M

F

O

R

T

FOR THE OWNER FOR THE QUALIFIED INSTALLER

Safety Precautions ................................................. 3

Commonwealth of Massachusetts......................15

Safety and Your Fireplace ......................................4

Owner’s Information ............................................... 5

Operating Your Fireplace for the First Time ............... 5

Cleaning Your Fireplace ............................................ 6

Checking Pilot and Burner Flames ............................ 7

Using Handset Wall Holder ........................................ 7

Replacing Batteries ...................................................7

Locating Lighting, Operation and Rating Information

Plate ..........................................................................8

Servicing Your Fireplace ............................................ 8

Operating Your Fireplace ........................................... 8

How to Turn Your Fireplace OFF (including pilot) ...... 8

How to Ensure Your Fireplace Cannot

Be Turned ON Inadvertently ...................................... 8

Automatic Shut-Off (in certain conditions) ................. 8

Remote Control Operation ..................................... 9

Options .................................................................. 13

Lighting Instructions ............................................14

Warranty ................................................................43

R

O

M

L

A

R

A

G

Warranty Card at the
back of this manual.

W

O

V

R

P

Y

T

T

N

A

R

R

R

A

O

C

F

O

M

Specifi cations ....................................................... 17

Dimensions, Clearance and Framing .................18

Venting ................................................................... 18

Co-Axial Venting ...................................................20

Co-Linear Venting ................................................. 27

Installation Planning ............................................28

Installation ............................................................. 29

Unpack Appliance .................................................... 29

Remove Window .....................................................29

Convert from Rear Outlet to Top Outlet

(co-axial venting) ..................................................... 29

Prepare Vent Outlet ................................................. 30

Connect Gas Supply ................................................31

Install Ceramic Walls (530IL and IC only) ................ 32

Install Ceramic Logs (530IL) ....................................33

Install Ceramic Coals (530IC) ..................................34

Install Ceramic Walls and Rocks (530IR) ................ 35

Refi t and Check Window ......................................... 37

Set-up Remote Control ............................................ 37

Check Operation ......................................................38

Set Aeration ............................................................. 38

Install Front, Trim and Barrier Screen ...................... 38

Install Remote Control Handset Wall Holder ........... 39

Wiring Diagram ..................................................... 40

Massachusetts: The piping and fi nal
gas connection must be performed by a
licensed plumber or gas fi tter in the State of
Massachusetts. Also, see Carbon Monoxide
Detector requirements on page 15.

190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1

2

Approved Venting Components .......................... 41

Warranty ................................................................43

Replacement Parts ............................................... 44

The information contained in this installation
manual is believed to be correct at the time of
printing. Miles Industries Ltd. reserves the right
to change or modify any information or specifi ca-
tions without notice. Miles Industries Ltd. grants
no warranty, implied or stated, for the installation
or maintenance of your heater, and assumes no
responsibility for any consequential damage(s).

Designed and Manufactured by / for

Miles Industries Ltd.

Tel. [phone] Fax [phone]

www.valorfi replaces.com

© Copyright Miles Industries Ltd., 2014. All rights reserved.

Safety Precautions

!

READ and UNDERSTAND all instructions carefully

before starting the installation. FAILURE TO FOLLOW
these installation instructions may result in possible fi re
hazard and will void the warranty.

Prior to the fi rst fi ring of the fi replace, READ the
Owner’s Information section of this manual.

DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualifi ed service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a
qualifi ed service person. The appliance and venting
system should be INSPECTED before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.

Always KEEP the appliance clear and free from
combustible materials, gasoline, and other fl ammable
vapors and liquids.

NEVER OBSTRUCT the fl ow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.

This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent
system or components MAY BE USED.

This gas fi replace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate
vent system. Common vent systems are PROHIBITED.

INSPECT the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air fl ow.

TURN OFF the gas before servicing this appliance.
It is recommended that a qualifi ed service technician
perform an appliance check-up at the beginning of each
heating season.

DO NOT use this heater as a temporary source of heat
during construction.

State of California. Proposition 65 Warning. Fuels
used in gas, wood-burning or oil fi red appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.

Due to the high temperature, the appliance should be
LOCATED out of traffi c areas and away from furniture
and draperies.

Clothing or fl ammable material SHOULD NOT BE
PLACED on or near the appliance.

This appliance is a DOMESTIC ROOM-HEATING AP-
PLIANCE. It must not be used for any other purposes
such as drying clothes, etc.

DO NOT place furniture or any other combustible
household objects within 36” of the fi replace front.

BE CAREFUL not to put any decorating objects
sensitive to heat to close above or around the fi replace
as it gets very hot when operating.

The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualifi ed
service person. DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the fi replace
manufacturer. NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.

A BARRIER DESIGNED TO REDUCE THE RISK OF
BURNS from the hot viewing glass is provided with
this appliance and SHALL BE INSTALLED for the

PROTECTION OF CHILDREN and other AT-RISK
INDIVIDUALS.

If the barrier becomes damaged, the barrier SHALL BE
REPLACED with the MANUFACTURER’S BARRIER

for this appliance.

Any safety screen, guard or barrier removed for ser­vicing the appliance, MUST BE REPLACED prior to
operating the appliance.

Children and adults should be ALERTED to the hazards
of high surface temperature and should STAY AWAY to
avoid burns or clothing ignition.

YOUNG CHILDREN should be CAREFULLY
SUPERVISED when they are in the same room as the

appliance. Toddlers, young children and others may
be susceptible to ACCIDENTAL CONTACT BURNS.
A physical barrier is recommended if there are at-risk
individuals in the house. To restrict access to a fi replace
or stove, INSTALL AN ADJUSTABLE SAFETY GATE
to keep toddlers, young children and other at-risk
individuals out of the room and away from hot surfaces.

3

Safety and Your Fireplace

!

Safety and Your Fireplace

Please Read and Carefully Follow all Safety Warnings and
Operating Instructions Contained in Your Owner’s Manual

(Replacement Manuals are available by contacting our service department at
1-800-468-2567 or visit www.valorfi replaces.com).

Please Follow These Important
Child Safety Precautions and
Recommendations,

• Parts of your Valor Fireplace become

extremely hot while in operation.

• The glass viewing window

temperature can
exceed 500 F

at full capacity.
Momentary contact
with a hot glass
surface can cause
a severe burn, even if the fi replace
is operating at reduced heating
capacity.

withdraw in the event of accidental
contact with a hot surface.

• A physical barrier is strongly

recommended if there are young
children, or at-risk individuals in the
house. Install an approved after­market safety gate to keep toddlers,
young children and other at-risk
individuals a safe distance from the
fi replace.

• Keep the remote control handset

out of reach of children at all
times. A wall mount storage holster

is provided with your remote control
handset.

• The glass window will remain hot

for an extended period of time after
the fi replace has been turned off.
Ensure that children are prevented
from touching the fi replace during the
cool down period.

• Toddlers and Young Children

must be closely supervised at all
times when they are in the same

room as the operating fi replace. They
lack full awareness of danger and
rely on your protection. Toddlers,
in particular, do not have the motor
skills and response refl exes to

4

• Ensure that the fi replace, including

the pilot light, is completely turned
off when children are present and

close supervision and safety barriers
are not available—see page 8 of

Owner’s Information section.

• If the fi replace is not going to be used

for the summer or any extended
period of time, remove the batteries

from the remote control handset
and receiver. It is recommended that

batteries are replaced annually in any
event—see page 7.

Owner’s Information

• • Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fi replace.

AVOID PLACING

candles, paintings, photos,

and other items

SENSITIVE TO HEAT

OWNER’S
INFORMATION

WARNING

!

EXTREMELY HOT!!!

• READ the SAFETY information on pages
3 and 4 of this manual BEFORE operating
your gas heater.

• Some parts of your fi replace are EXTREMELY
HOT, particularly the GLASS window.

• DO NOT LET CHILDREN touch the glass or
any parts of your fi replace even after it is
turned off as it is still hot.

• USE THE SAFETY SCREEN provided with
the front or trim or a GATE to reduce the risk
of burns.

• Keep the remote control handset OUT OF
REACH of children.

• HOT HEARTH / FLOOR! The hearth or fl oor in
front of the fi replace may become very hot when
the fi replace heats. Do not use the hearth as a
seat or shelf.

Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fi replace.

AVOID PLACING

and other items
36 inches (0.9 m) around the fi replace.

candles, paintings, photos,

SENSITIVE TO HEAT within

Thank You ...

For purchasing a Valor by Miles Industries. Your new
radiant gas heater is a technical appliance that must
be installed by a qualifi ed dealer. Each Valor fi replace
is fully tested during the production process for your
safety and comfort.
Your unit has been professionally installed by:

Dealer Name: ________________________________

Phone Number :_______________________________

Should you encounter an operational problem, call
your dealer immediately.

Do not try to repair the unit as you may cause an
injury or damage the fi replace.

This manual and particularly the preceding
and following pages contain very important
information regarding the safe operation of your
fi replace as well as maintenance instructions.

Read carefully BEFORE operating your fi replace
and pay special attention to the SAFETY
WARNINGS.

A heating gas appliance does require safe handling
and for this reason, we very strongly recommend that
no children be allowed to touch the fi replace and its
controls at all times. Do install a screen or barrier

in front of the fi replace to protect your children
against severe burns.

• Solid wood fl ooring in front of the fi replace (if
allowed) may shrink during the heating season
due to heat.

Performance of LPG appliances may be affected by
the quality of commercial gas supplied in your area.

Fireplace

Hearth

Do not put

furniture or other objects

in this space in front of

the replace:

36” (0.9 m)

Operating Your Fireplace for the First Time

When operating your new fi replace for the fi rst time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the fl ames to be the full height of the fi rebox, or
even slightly higher, for the fi rst few hours of operation.

It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the fl ames will be at their normal height.

Flame Supervision Device

For your safety, this appliance is fi tted with a fl ame
supervision device which will shut-off the gas supply
if, for any reason, the pilot fl ame goes out. This device
incorporates a fi xed probe, which senses the heat
from the pilot fl ame. If the probe is cool, the device will
prevent any gas fl ow unless manually lighting the pilot.
See full lighting instructions on page 14 of this manual.

5

OWNER’S
INFORMATION

Owner’s Information

Cleaning Your Fireplace

WARNING

!

DO NOT TOUCH THE GLASS WHILE IT IS HOT!

Let the fi replace cool fi rst before cleaning it.

Important - Glass cleaning - Mineral deposits

One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white fi lm on the ceramic glass of the viewing door.

The composition of the deposit varies with location and
time. It is believed to be associated with the varying
sulfur content of the gas. You may have the problem
intermittently.

We have consulted with ceramic glass manufacturers
and they cannot offer a defi nitive solution to this prob-
lem. Dealers have tried various cleaning products with
varying results. The following are recommendations
only and are not meant to guarantee results.

NOTE: This is a problem beyond Miles Industries’
control and is not covered under warranty.

• Clean the glass regularly as soon as you notice

the buildup (white fi lm). If the fi lm is left for a longer
period of time, it will etch into the glass. It is then
much harder, if not impossible, to remove.

• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the

immediate effect of compromising the strength of the
glass. An emulsion type cleaner is recommended.

• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive to
ceramic glass and should be avoided.

• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.

• Brasso, Polish Plus by Kelkem, Cook Top Clean

Creme by Elco, White Off by Rutland, Turtle Wax

Do not clean the glass while it is hot!

Always securely replace the window and the barrier
screen before lighting.

If broken, the glass pane may only be replaced
as a complete window unit as supplied by the
manufacturer.

To remove the window for
cleaning:

1. Unhook the front and barrier
screen.

2. Release the top of the window
by pulling forward and rotating
outwards the two bars at the top
corners.

3. Unscrew the two spring-loaded
bolts securing the bottom of the
window.

4. Carefully lift the window. Keep the
window and bolts in a safe place.

Clean the window following the guidelines in this
section.
Clean the trim or front with mild soap and water.

Dust the barrier screen with a soft brush.
Dust the fi rebox ceramic logs/rocks and walls with a

soft brush. Dust can also be removed from the burner
using a soft brush after removing the ceramic logs.

When cleaning, make sure that no particles are
brushed into the slots of the burner.

To refi t the window:

1. Place the window centrally
against the engine unit resting it
on the support at bottom front of
the engine.

2. Pull the clamping bars forward
and rotate inwards to secure the
top of the window.

3. Fit the two spring loaded bolts
through the bottom of the window
and tighten to secure the bottom
of the window.

4. Pull the top of the window
forward and release to ensure the springs return it in
position.

5. Similarly check the bottom of the window by pulling
it forward and releasing.

IMPORTANT: To ensure a safe operation, ensure that
the spring-loaded mechanism functions properly.

6. Apply light hand pressure against the window frame
sides to bed in the window seal.

If the barrier becomes damaged, the barrier shall
be replaced with the manufacturer’s barrier for this
appliance.

6

Owner’s Information

OWNER’S
INFORMATION

7. If the Hot Glass Warning plate has been removed

from the front lower corner of the window,
reinstall it by sliding it between the glass and
the frame as indicated.

Safety warning plate

8. Reinstall the front and barrier screen.

WARNING

!

FOR SAFETY PURPOSE, ensure the
barrier screen is re-installed on the fi replace
front after maintenance.

Checking Pilot and Burner Flames

A periodic check of the pilot and burner fl ames should
be made. Check after the fi re has been on for at least
30 minutes. The pilot fl ame must cover the tip of the
thermocouple probe. The main burner fl ame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions.

With Logs

With Rocks

Correct fl ame appearance

With Coals

Thermocouple
probe must be
in flame

The appliance area must always be kept clear and
free from combustible materials, gasoline and other
fl ammable vapors and liquids. Inspect the vent terminal
outdoors regularly to make sure that dirt, snow, insects,
leaves, shrubs, trees do not obstruct it. Examine the
whole vent system regularly. We recommend annually.

Using Handset Wall Holder

Your fi replace equipment includes a wall
holder to store the handset. If it hasn’t be
installed, refer to the instructions further
on in this manual for the installation.

Replacing Batteries

Low battery signal: see page 13.

WARNING

!

DO NOT ATTEMPT TO CHANGE THE BATTER­IES WHILE THE FIREPLACE IS STILL HOT! Let

the fi replace cool fi rst before touching it.

CAUTION

DO NOT USE a screwdriver or other metallic object to

remove the batteries from the receiver or the handset!
This could cause a short circuit to the receiver.

BEFORE changing the batteries, turn off the valve
using the manual On/Off switch —see instructions on

next page.

The appliance uses four 1.5 V AA alkaline batteries for
its remote control receiver and one 9 V alkaline battery
for its handset. The batteries should last one to two
seasons, depending on usage. Removing the batteries
in the off-season will extend the battery life. Should the
batteries loose power, the control may be operated by
manually turning the control knob at the valve or by
turning off the valve at the switch.

To replace the batteries in the remote control
receiver:

1. The receiver is located to the left of the valve and it

is retained to the fi rebox by a Velcro tab. Grab the

receiver and pull it out from its location.

2. Slide and remove the receiver cover.

3. Replace batteries with 4 AA alkaline batteries.

4. Replace the cover.

5. Put the receiver back in its position pushing it in so

it attaches to the Velcro tab.

7

Valve Switch

OWNER’S
INFORMATION

Owner’s Information

Locating Lighting, Operation and Rating
Information Plate

WARNING

!

DO NOT ATTEMPT TO TOUCH THE DATA PLATE
WHILE THE FIREPLACE IS STILL HOT! Let the

fi replace cool fi rst before touching it.

The Lighting, Operation and Rating information is
located on a plate under the fi rebox.

To access the plate, remove any fret or access panel
and grab the plate and slide it out to read it. There is
important information on both sides of the plate.

Servicing Your Fireplace

If your appliance require any attention, contact your
supplier quoting the model number. It will be helpful if
the appliance serial number can also be quoted. This is
on the rating plate located under the fi rebox. The repair
parts are shown in the separate repair parts leafl et.
Please always quote part number and description when
requesting spare parts.

Operating Your Fireplace

There are three ways to control your fi replace.

1. Thermostatic Remote Control;

2. Manual On/Off Switch;

3. Wall Switch (optional) .

The Thermostatic Remote Control can be programmed
to function automatically—see pages 9–13.

The manual On/Off switch must be ON for the fi replace
to function. It can be used to shut off the fi replace in
case of emergency—see above.

The Wall Switch (optional) can be used to turn on, off
and to increase or decrease the fl ame height—see
1265WSK—Wall Switch Kit.

NOTE: The remote control in the AUTO mode will
override the wall switch.

ON

OFF

Thermostatic Remote

Control

Wall Switch

(optional)

Manual On/Off Switch

How to Turn Your Fireplace OFF (including pilot)

Familiarize yourself with each of these methods before
operating your fi replace.

Handset and Wall Switch: Press and hold the OFF
button for a second (either on the handset or the wall
switch).

If the fl ames are on, they go down and you hear the
valve motor wind down. You hear a clunk and a beep
indicating that the valve has received the signal from
the remote control.

Remote control

handset

Wall Switch

(optional)

Manual ON/OFF Switch: Press the O button.

— O

ON

OFF

O

How to Ensure Your Fireplace Cannot
Be Turned ON Inadvertently

You can use one of the two following methods to
ensure that your fi replace will not turn on when you
don’t want it on.

First, ensure your fi replace is turned off—including
the pilot—and cold BEFORE going ahead.

• You can prevent your fi replace from lighting by
pressing the O button on the manual ON/OFF
switch on the gas valve—see image above.

• Alternately, you can remove all batteries from the
receiver as well as the battery from the handset.

Automatic Shut-Off (in certain conditions)

Your fi replace’s remote control is equipped with an
automatic shut-off mechanism which is activated in

certain conditions. See page 13 in the Remote Control
Operation section for a description of this feature.

8

Remote Control Operation

Current

temperature

(F or C)

Current time
(12 or 24 hour clock)

Modes (Manual,
Temperature, Timer)

Handset
sensor

Battery status

Current

programmed

period (Timer)

Period

start or end

(Temp, Timer)

OWNER’S
INFORMATION

NOTE: Before using the remote control system
for the fi rst time, the receiver and the handset must

be synchronized. See the sub-section Set-up Remote
Control on page 37 of this manual.

Display Overview

Note: In the TEMP or TIMER modes, the remote
handset senses the room temperature and adjusts the
fl ame accordingly.

To communicate, the handset should be within 15 feet
(4.5 meters) of the fi replace.

Do not leave the handset on the mantel or hearth.

IMPORTANT: BEFORE YOU BEGIN, please note that
on this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when
the function display is fl ashing. Be patient when
programming as it can take a few seconds to set.

Large ame

Set (scrolls

through

modes and

settings)

OFF (returns

to set mode,

turns the burner

and the pilot o)

Handset Overview

button (ames
up, sets hours,
temperature)

Small ame
button (ames
down and o,
sets minutes,
temperature)

TO TURN ON APPLIANCE TO TURN OFF APPLIANCE

CAUTION

When pilot ignition is confi rmed, motor turns
automatically to maximum fl ame height.

• On the valve, turn MAN knob on the ON, full
counterclockwise position.

• Place ON/OFF switch (if equipped) in I (ON
position).

• Simultaneously press the OFF and

(large fl ame) buttons until a short
beep confi rms the start sequence
has begun; release buttons.

• Continuing beeps confi rm the

ignition is in process.

• Once pilot ignition is confi rmed,
there is main gas fl ow.

• After main burner ignition the

handset will automatically go into
manual (MAN) control mode.

• Press OFF button.

When the pilot is off, it will take 2

When the pilot is off, it will take 2

minutes before it can be lit again.

minutes before it can be lit again.

STANDBY MODE (Pilot Flame)

• Press and hold (small fl ame) to set appliance at
pilot fl ame.

FLAME HEIGHT ADJUSTMENT

• In standby mode: Press and hold

(large fl ame) button to increase
fl ame height.

9

OWNER’S
INFORMATION

Remote Control Operation

• Press and hold (small fl ame)
button to decrease fl ame height or
to set the appliance at pilot fl ame.

• For fi ne adjustment tap the
(large fl ame) or (small fl ame)
buttons.

Express Low and High Fire

• Double-click (small fl ame)
button. “LO” will be displayed.
NOTE: Flame goes to high fi re fi rst
before going to designated low fi re.

x 2

• Double-click (large fl ame)
button. Flame automatically goes
to high fi re. “HI” will be displayed.

x 2

SETTING ºC/24-HOUR OR ºF/12-HOUR CLOCK

• In MAN mode, press OFF and
(small fl ame) buttons until display
changes from Fahrenheit/12-hour
clock to Celsius/24-hour clock and
vice versa.

SETTING THE TIME

• The time display will fl ash after
either:

• Installing the battery or

• Simultaneously pressing the

(large fl ame) and (small fl ame)
buttons.

• Press (large fl ame) button to
set the hour.

• Press (small fl ame) button to
set the minute.

• Press OFF or simply wait to return
to MAN mode.

MODES OF OPERATION

• Briefl y pressing the SET button

changes the mode of operation in
the following order:

MAN

→ →

TIMER

→ → and back to .

TEMP

TEMP

MAN

NOTE: Manual mode can also be reached by pressing

either the (large fl ame) or the (small
fl ame) buttons.

MAN

• - Manual Mode - Manual
Flame Height Adjustment.

TEMP

• - Daytime Tempera-
ture Mode (Appliance must be in

standby mode; pilot ignited) - The
room temperature is measured and
compared to the set temperature.
The fl ame height is then auto-
matically adjusted to achieve the
Daytime Set Temperature.

TEMP

• - Nighttime Setback
Temperature Mode (Appliance

must be in standby mode; pilot
ignited) - The room temperature
is measured and compared to the
Nighttime Setback temperature.
The fl ame height is then automati-
cally adjusted to achieve the Night­time Setback Temperature.

TIMER

• - Timer Mode (Appliance
must be in standby mode; pilot
ignited) - The timers P1 and P2

(Program 1, Program 2) each can
be programmed to go ON and OFF
at specifi c times. For instructions
see Timer Programming Mode.

NOTE: The display shows the set temperature every

30 seconds.

10

Remote Control Operation

SETTING THE ON / OFF TEMPERATURES

SETTING THE “DAYTIME” TEMPERATURE

Default Settings: (sun), 23ºC / 74ºF

TEMP

OWNER’S
INFORMATION

SETTING THE “NIGHTTIME SETBACK” TEMPERA­TURE

Default Settings: (moon), “--” (OFF)

TEMP

• Briefl y press SET button to scroll to

TEMP (sun) mode. Hold

TEMP

the SET button until the TEMP
fl ashes.

• Press (large fl ame) button

to increase the Daytime Set
Temperature.

• Press (small fl ame) button

to decrease Daytime Set
Temperature.

• Briefl y press SET button to scroll to

TEMP (moon) mode. Hold

TEMP

the SET button until the TEMP
fl ashes.

• Press (large fl ame) button to

increase Nighttime Setback
Temperature.

• Press (small fl ame) button to

decrease Nighttime Setback
Temperature.

• Press OFF or simply wait to
complete programming.

• Press OFF or simply wait to
complete programming.

Tip

Set the different parameters when they are fl ashing.

11

OWNER’S
INFORMATION

Remote Control Operation

SETTING PROGRAM TIMERS

• You can program two periods of time between 12:00
am and 11:50 pm in each 24-hour cycle.

• The Programs P1 and P2 must be set in the
following order during a 24-hour cycle: , ,

P2

and .

• The icon indicates the beginning of the period (ON)
and the icon indicates the end of the period (OFF).

P1

• If = or = , the programming
is cancelled.

• To keep the fi replace ON all night, set at
11:50 am and at 12:00 am.

P1

P2

P1

P2

P2

P1

P2

P1

Default settings:

Program 1: 6:00 am 8:00 am
Program 2: 11:50 pm 11:50 pm

P1

P2

• Briefl y press SET button to scroll to

TIMER mode.

P1

P2

SETTING P1 OFF TIME

• Briefl y press SET button to scroll

to TIMER (moon) while the
time fl ashes.

• Press (large fl ame) button to set

the hour.

• Press (small fl ame) button to

set the minutes.

P1

SETTING P1 ON TIME

• Hold the SET button until
(sun) is displayed and the time
fl ashes.

• Press (large fl ame) button to
set the hour.

• Press (small fl ame) button to
set the minutes.

P1

SETTING P2 ON TIME

• Briefl y press SET to scroll to TIMER mode
(sun) while the time fl ashes.

• Follow the instructions given to set P1 ON time.

P2

SETTING P2 OFF TIME

• Briefl y press SET to scroll to TIMER mode
(moon) while the time fl ashes.

• Follow the instructions given to set P1 OFF time.

Press OFF button to save these settings. The timers
are programmed. See the diagram on programming
sequences on the following page.

P2

Tip

If you want to program only one period, program
and with desired times and program and

P1

P2

with the same time as .

P1

P1

P2

12

Remote Control Operation

Timer Programming Example (default temperatures shown)

OWNER’S
INFORMATION

6:00 a.m.—
P1

☼

Start time

Set temp 74˚F Set temp 40˚FSet temp 74˚F

☼

AUTOMATIC TURN DOWN

• No communication. If there is no communication
between the receiver and the handset for a period of
6 hours, the appliance goes into pilot mode.

• No change in fl ame height. If there is no change
in fl ame height for a period of 6 hours, the appliance
goes into pilot mode.
NOTE: In TEMP or TIMER modes, the fl ame height
will vary according to room temperature. The appli­ance will continue to work normally. However, if the
room temperature remains the same for 6 hours, the
appliance will go into pilot mode.

AUTOMATIC SHUT OFF

• Low batteries in the receiver. With low battery
power in the receiver the system shuts off
completely.
NOTE: This does not apply when the power supply
is interrupted.

• No change in pilot. The appliance shuts off
completely when it is continually in pilot position—
without any change—for a period of 5 days.

8:00 a.m.—
P1

☽

End time

Set temp 40˚F

☽☽

4:00 p.m.—
P2

☼

Start time

LOW BATTERY INDICATION

DO NOT USE a screwdriver or other metallic object

to remove the batteries from the battery box or the
handset! This could cause a short circuit.

Remote handset: The battery icon will show
when the battery needs to be replaced.
Replace with one 9 V alkaline battery.

Receiver: Three short ‘beeps’ will sound when the
motor turns when the batteries need to be replaced.
Replace with four 1.5 V alkaline batteries.

HANDSET / RECEIVER MATCH

The remote control handset and receiver are program­med to function together. In case of a replacement of
the handset or the receiver, you will need to reset the
receiver to allow them to function together. Contact your
dealer for details.

☼

10:00 p.m.—
P2

☽

End time

CAUTION

6:00 a.m.—
P1

☼

Start time

Required Kits*

Fronts (choose one)

531CSB—President Stove FS with Barrier Screen

4003288

536CXB—President ZC Front with Barrier Screen

4003359

541BPC—Bolero Front with Barrier Screen 4003289
539/549/559—Windsor and Classic Arches with Barrier

Screen 4003290

563CSB—Senator Front with Barrier Screen 4003291
569—Ledge Fronts with Barrier Screen 4003375
575-576-578—Lift Stove with Barrier Screen 4003429

Options

Optional Kits*

567FGP—Top Grille (with logs or rocks ONLY)
580EBL—Enamel Liner Kit
1265WSK—Wall Control Switch Kit
555CFK—Circulating Fan Kit

Gas Conversion Kit

530NGK—Conversion Kit LPG to NG
530PGK—Conversion Kit NG to LPG

Hearth Gate

Hearth gates such as Cardinal’s VersaGates are
available at retail stores carrying safety products
for children.

*Information accurate at the time of printing and subject to
change without notice.

13



X

OWNER’S
INFORMATION

WARNING: If you do not follow these instructions exactlyD¿UHRUH[SORVLRQPD\UHVXOWFDXVLQJ

SURSHUW\GDPDJHSHUVRQDOLQMXU\RUORVVRIOLIH

A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly.To

save gas, turn the pilot off when not using the appliance for a prolonged period of time.

%%()25(/,*+7,1*VPHOODOODURXQGWKHDSSOLDQFHDUHDIRUJDV%HVXUHWRVPHOOQH[WWRWKHÁRRUEHFDXVHVRPHJDV

DUHKHDYLHUWKDQDLUDQGZLOOVHWWOHRQWKHÁRRr.

WHATTO DO IFYOU SMELL GAS

'RQRWWU\WROLJKWDQ\DSSOLDQFH
'RQRWWRXFKDQ\HOHFWULFVZLWFKGRQRWXVHDQ\SKRQHLQ\RXUEXLOGLQJ

,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPDQHLJKERr’s phone. Follow the gas supplier’s instructions.
,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHrFDOOWKHÀUHGHSDUWPHQW

C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by hand,

GRQ·WWU\WRUHSDLUWKHPFDOODTXDOLÀHGVHUYLFHWHFKQLFLDQ)RUFHRUDWWHPSWHGUHSDLUPD\UHVXOWLQDÀUHRUH[SORVLRQ

D. Do not use this appliance if any part has been under water,PPHGLDWHO\FDOODTXDOLÀHGVHUYLce technician to inspect

the appliance and to replace any part of the control system and any gas control, which has been under water.

1. STOP! Read the safety information above.Dependent on model, switch #1 may be mounted directly to valve see Fig 2A.

Lighting Instructions

FOR YOUR SAFETY, READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

)LJ

2. SET ON/OFF SWITCH (1) TO “OFF” POSITION.



WDLWÀYHPLQXWHVWRFOHDURXWDQ\JDVWKHQVPHOOIRUJDVLQFOXGLQJQHDUWKHÁRRr. If you smell gas, STOP! Follow

“B” in the safety information above on this label. If you don’t smell gas, go to the next step.

3. AUTOMA7,&,*1,7,21ÀJ/RFDWHWKHSLORWÀJLQVLGHRIÀUHER[DW/HIW+DQGVLGH



212))VZLWFKLQ21SRVLWLRQ0$1NQRELQ21SRVLWLRQVHW)ODPH Adjustment knob (3) to lowest setting

(3);



On the remote control handset, press and hold the ‘off ’ button and (large flame) VLPXOWDQHRXVO\DVKRUW

DFRXVWLFVLJQDOFRQÀUPVWKHVWDUWKDVEHJXQ



)XUWKHUVKRUWDFRXVWLFVLJQDOVLQGLFDWHWKHLJQLWLRQSURFHVVLVLQSURJUHVV



When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the highest setting.



Press the (small flame)RQWKHUHPRWHFRQWUROKDQGVHWWRUHGXFHWKHÁDPHKHLJKW

4. MANUAL,*1,7,21ÀJWLWKWKHZLQGRZRIIORFDWHWKHSLORWÀJ

LQVLGHRIÀUHER[DW/HIW+DQGVLGH



212))VZLWFKLQ21SRVLWLRQ0$1NQRELQ0$1SRVLWLRQ



Set Flame Adjustment knob (3) to the lowest setting (3);



3XVKGRZQWKHPHWDOOLFFRUHZLWKDSHQRUVLPLODULQVWUXPHQWWKLVZLOOHVWDEOLVKWKHSLORWJDVÁRZ
/LJKWJDVDWWKHSLORWZLWKDPDWFK
&RQWLQXHKROGLQJGRZQPHWDOFRUHIRUDERXWVHFRQGVDIWHUUHOHDVHSLORWVKRXOGUHPDLQOLW



5HLQVWDOOWKHZLQGRZDQGVHWWKH0$1NQREWR´21µWXUQ)ODPH Adjustment knob (3) up (4) or down

manually or use the up/down ‘flame’ buttons on the remote control handset to adjust theÁDPHKHLJKW

If the pilot will not stay lit after several tries, turn the gas control knob (3) to “OFF” (3) and call your local
service technician or gas supplier.

)LJ

)LJ$

TO TURN OFF GAS TO APPLIANCE

1. AUTOMATIC SHUT2))XVLQJWKHUHPRWHFRQWUROKDQGVHW



Press and hold the (small flame) RQWKHUHPRWHFRQWUROKDQGVHWWRVKXWRIIWKHPDLQEXUQHUJDVÁRZ



3UHVV´2))µEXWWRQRQUHPRWHKDQGVHWWRVKXWRIIWKHDSSOLDQFHLQFOXGLQJSLORWÁDPH

2. MANUAL SHUT-OFF (using only the ON/OFF switch (1))
Press “O” the ON/OFF switch (1) to shut-off the appliance.



)LJ

14

Commonwealth of Massachusetts

QUALIFIED
INSTALLER

State of Massachusetts Carbon Monoxide
Detector/Vent Terminal Signage
Requirements

For all side wall horizontally vented gas fueled
equipment installed in every dwelling, building or
structure used in whole or in part for residential
purposes, including those owned or operated by the
Commonwealth and where the side wall exhaust
vent termination is less than seven (7) feet above
fi nished grade in the area of the venting, including
but not limited to decks and porches, the following
requirements shall be satisfi ed:

1. INSTALLATION OF CARBON MONOXIDE
DETECTORS. At the time of installation of the side wall
horizontal vented gas fueled equipment, the installing
plumber or gas fi tter shall observe that a hard wired
carbon monoxide detector with an alarm and battery
back-up is installed on the fl oor level where the gas
equipment is to be installed. In addition, the installing
plumber or gas fi tter shall observe that a battery
operated or hard wired carbon monoxide detector
with an alarm is installed on each additional level of
the dwelling, building or structure served by the side
wall horizontal vented gas fueled equipment. It shall
be the responsibility of the property owner to secure
the services of qualifi ed licensed professionals for the
installation of hard wired carbon monoxide detectors.

3. SIGNAGE. A metal or plastic identifi cation plate
shall be permanently mounted to the exterior of the
building at a minimum height of eight (8) feet above
grade directly in line with the exhaust vent terminal for
the horizontally vented gas fueled heating appliance
or equipment. The sign shall read, in print size no less
than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of
the side wall horizontally vented gas fueled equipment
shall not approve the installation unless, upon
inspection, the inspector observes carbon monoxide
detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt
from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled
“Equipment Not Required To Be Vented” in the most
current edition of NFPA 54 as adopted by the Board;
and

2. Product Approved side wall horizontally vented
gas fueled equipment installed in a room or structure
separate from the dwelling, building or structure used in
whole or in part for residential purposes.

a. In the event that the side wall horizontally vented
gas fueled equipment is installed in a crawl space or
an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next
adjacent fl oor level.

b. In the event that the requirements of this subdivision
can not be met at the time of completion of installation,
the owner shall have a period of thirty (30) days
to comply with the above requirements; provided,
however, that during said thirty (30) day period, a
battery operated carbon monoxide detector with an
alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS.
Each carbon monoxide detector as required in
accordance with the above provisions shall comply
with NFPA 720 and be ANSI/UL 2034 listed and IAS
certifi ed.

(c) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM PROVIDED.
When the manufacturer of Product Approved side
wall horizontally vented gas equipment provides a
venting system design or venting system components
with the equipment, the instructions provided by the
manufacturer for installation of the equipment and the
venting system shall include:

1. Detailed instructions for the installation of the venting
system design or the venting system components; and

2. A complete parts list for the venting system design or
venting system.

15