Valcom VIP-9831 Specifications
VIP-9831 IP Stealth Horn One-Way
INTRODUCTION
The VIP-9831 IP Stealth Horn One-Way is a self
contained paging system which enables voice paging
up to 300 feet from an Ethernet connection. The
VIP-9831 consists of a horn and Network/Audio
Interface board allowing stand alone capability when
used with a SIP enabled telephone system or can be
accessed from a variety of Valcom managed VoIP
products.
SPECIFICATIONS
Access Methods
PBX, FXO Port w/VIP-811
POTS telephone set w/VIP-811
PBX, FXS Port w/VIP-821
Valcom M Cast Page Group
SIP telephone system
Features
RJ-45 network connection
Network activity LEDs
Power over Ethernet (PoE) 802.3af compatible
Dimensions/Weight
9.3 "H x 15.0 "W x 5.0 "D (23.6 cm x 38.1 cm x
12.7 cm)
Weight: 5.5 lbs (2.05 kg)
Shipping Weight: 6.0 lbs (2.24kg)
Environment
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Indoor use only
Power
Via 802.3af PoE Ethernet Switch: Class 3
ISSUE 2
Precautionary Designations
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock,
Refer servicing to qualified service personnel.
Do not remove cover.
No user serviceable parts inside.
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.
Packing List
Qty Item
1 VIP-9831 IP Horn
1 VSP Document
4 Mounting Screws
INSTALLATION
FCC Information
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates uses
and can radiate radio frequency energy and if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area may cause
harmful interference in which case the user will
be required to correct the interference at his own
expense.
1 947789
Mounting (Enclosure / Horn)
The horn should be mounted 8 to 12 feet above the
floor to allow for best sound distribution. This unit
can be mounted to a single gang, double gang,
octagon electrical box or wall. Refer to Figure 1.
Using a Phillips screwdriver, remove 4
screws attaching grille to enclosure base.
Using a11/32 nut driver, carefully remove
horn bracket assembly.
Carefully disconnect the black and white
speaker wires from Network/Audio PC board
Mount enclosure base to wall using
appropriate hardware.
Reconnect black and white speaker wires to
Network/Audio PC board.
Install horn bracket assembly.
Connect a 802.3af compliant PoE port (300
feet maximum distance) to network
connector on Network/Audio PC board.
Install grille onto enclosure base.
Status Indicator Lights
The VIP-9831 has 2 status indication lights located
on network jack:
Left LED: (Link) Indicates 100 Mbit Ethernet
connection when illuminated. No activity indicates 10
Mbit connection.
Right LED: (Activity) Indicator flashes to indicate
network activity
Operation
Provide paging from SIP connection or via a variety
of Valcom managed VoIP products. Integration to
customer telephone system can be via SIP
registration, FXO port (with VIP-811), or FXS port
(with VIP-821).
Setup
Information specific to your application will need to be
programmed into the VIP-9831 using a computer.
Setup will be done using the IP Solutions Setup Tool.
The IP Solutions Setup Tool may be downloaded
from the Valcom website at www.valcom.com.
TECHNICAL ASSISTANCE
Assistance is available from the factory when
problems are encountered. Call (540) 563-2000 and
press 1 for Technical Support or visit our website at
http://www.valcom.com.
Valcom equipment is not field repairable. Valcom,
Inc. maintains service facilities in Roanoke, VA.
Should repairs be necessary, attach a tag to the unit
clearly stating your company name, address, phone
number, contact person and the nature of the
problem. Send the unit to:
Valcom, Inc.
Repair & Return Dept.
5614 Hollins Road
Roanoke VA. 24019
2 947789
Loading...