Valcom VIP-822 User Manual

VIP-822

DUAL NETWORKED TRUNK PORT

INTRODUCTION

The VIP-822 Dual Networked Trunk Port allows
most loop start terminal devices to be connected to
a managed IP-based LAN/WAN.

SPECIFICATIONS

Access Methods

• PBX, FXS Port

ISSUE 1

Features

• RJ-45 for network connection

• 2 RJ-11 FXO connections

• 2 RJ-11 failover telephone connections

• Decode Caller ID signals

• Front panel activity LED

• Network activity LEDs

• 2.5mm jack for DC power

• 802.3af compliant

Dimensions/Weight

• 1.75 H x 6.75" W x 9.5" D
(4.45cm H x 17.15cm W x 24.13cm D)

• Weight: 1.75 lbs. (0.80 kg)

Nominal Specifications

Input Impedance: 600 Ohms
Input Level: -10dBm
Output Impedance: 600 Ohms
Output Level: - 10dBm nominal

Nominal Power Requirements

Via back panel barrel connector:

Voltage: 24VDC
Current: 325mA

Via 802.3af PoE Ethernet Switch:

802.3af: Class 3

Environment

Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-822
1 VIP-101 Setup CD
1 VSP Document
2 Mounting Brackets
4 Rubber Feet
6 Wood Screws
1 RJ-45 Patch Cables

1 947998

INSTALLATION

NOTE: The telephone system referred to in this
manual is the customer premise equipment
such as an electronic key system, a PBX or a
dedicated single line telephone sets. The
VIP-822 is not intended for direct or indirect
connection to the public telephone network.
When used with a customer premise telephone
system such as a key system or PBX system,
these units are interfaced to the system via a
fully protected page port or system central
office port, which is a fully protected interface
device. Also, the host system must be
configured to disallow central office trunk
conferencing in order to prevent indirect
connection to the public network.

Precautionary Designations

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Mounting

The VIP-822 is designed for wall, table or rack
mounting.

Table: Provided with the VIP-822 are four rubber
stick on feet. Peel these feet off their carrier
backing and place at the four corners of the bottom
of the unit.

Wall: Using the template and instructions provided,
secure the VIP-822 to the wall.

Rack: Following the assembly drawing, attach the
two mounting ears to the VIP-822 unit. Using rack
screws, mount the VIP-822 in an available 1U rack
slot.

CAUTION: To reduce the risk of electric shock,

Refer servicing to qualified service personnel.

Do not remove cover.

No user serviceable parts inside.

This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.

This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.

FCC Information

This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses and can radiate radio
frequency energy and if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment
in a residential area may cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.

Power Connections

The preferred method of powering a VIP-822 is via
a power over Ethernet switch meeting the 802.3af
specification. The Valcom VIP-908 Ethernet switch
which is ideal for this purpose and will power up to
7 VIP-800 series devices.

If the rear panel barrel connector is used for power,
the preferred power supply is a Valcom VIP-324.

Make all required signal connections before
applying power to the unit. If powering via 802.3af,
make sure all signal connections via the back
panel are made then connect the VIP-822 to the
Ethernet switch.

If power is supplied via the barrel connector, make
sure all signal connections are secure. Attach the
unit to the network via the front panel RJ-45
Ethernet connector. Apply power by plugging the
power supply into the VIP-822 via the barrel
connector on the rear of the VIP-822.

2 947998

Signal Connections

Trunk Connections:

Connect standard analog telephones to the
VIP-822 via the rear panel RJ-11 jacks labeled
Port 1 Line or Port 2 Line. Tip and Ring appear on
pins 3 and 4 of these jacks.

ED

Failover Telephone Connections:

Connect standard analog telephones to the
VIP-822 via the rear panel RJ-11 jacks labeled
Port 1 Phone or Port 2 Phone. Tip and Ring
appear on pins 3 and 4 of these jacks.

Front Panel

Rear Panel

Status Indicator Lights

The VIP-822 has 3 status indication lights on the
front panel.

STATUS: Flashes then illuminates to indicate
power.

LINK: Indicates 100 Mbit Ethernet connection
when illuminated. No activity indicates 10 Mbit
connection.

ACT: Indicator flashes to indicate network activity.

TECHNICAL ASSISTANCE

When trouble is reported, verify power is being
supplied to the unit and there are no broken
connections. Check voltages for proper polarity to
the one-way amplified speakers. If a spare unit is
available, substitute a spare unit for the suspected
defective unit.

Assistance in troubleshooting is available from the
factory. Call [phone] and press 1 for
Technical Support or via email at
[e-mail].

When requesting assistance, you should include
all available information. It is strongly suggested
that you go to the website and follow the trouble
resolution procedure at http://voip.valcom.com.

Valcom equipment is not field repairable. Valcom,
Inc. maintains service facilities in Roanoke, VA.
Should repairs be necessary, attach a tag to the
unit clearly stating your company name, address,
phone number, contact person and the nature of
the problem. Send the unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

Valcom, Inc. warrants its products to be free from defects in materials and workmanship under conditions of normal use and service for a
period of one year from the date of shipment. The obligation under this warranty shall be limited to the replacement, repair or refund of any
such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus
parts and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units ‘out of warranty’ are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to
additional charges for parts and labor).

This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Valcom, Inc. be liable for any
anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation or
use of the product.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should
be notified immediately.

Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

VALCOM LIMITED WARRANTY

3 947998